Differential Pressure Gauges - Page 19

Manufacturer: Mid-West Instrument Brand: Mid-West Instrument Model: 522-AA-02-AO

Mid-West Instrument diaphragm type differential pressure gauge. Weather resistant construction standard. Shatter resistant acrylic lens. Ideally suited for use on dissimilar fluids and wet gas or fluids with particulates present. Common applications: filter/strainer monitoring, compressed air, hydraulic, refrigerant, pump performance testing, heat exchanger pressure drop monitoring, water treatment applications. Aluminum body material. 316 Stainless steel/ceramic/acetyl moving components. Buna-N seal material. 1/4-inches FNPT end connections, 2-1/2-inches uni-directional black on white round dial, weather resistant engineered plastic case, accuracy +/-5 percent full scale (ascending). Two 10-32 mounting holes, spaced 1.75-inches apart by 0.330-inches deep.

Manufacturer: Mid-West Instrument Brand: Mid-West Instrument Model: 140-SA-00-O(AA)

Mid-West Instrument diaphragm type differential pressure gauge. Over range protection to full rated working pressure. Weather resistant construction standard. Shatter resistant acrylic lens. Ideally suited for use on dissimilar fluids and wet gas or fluids with a high concentration of solids. Proof pressure: two times rated working pressure at ambient temperature. Common applications: filter/strainer monitoring, compressed air, hydraulic, refrigerant, pump performance testing, heat exchanger pressure drop monitoring, water treatment applications, tank level monitoring horizontal or vertical, flow monitoring and balancing. 316 Stainless steel body material. 316 Stainless steel internal metal part. Buna-N seal material. 1/4-inches FNPT back connections, 2-1/2-inches uni-directional round dial, weather resistant engineered plastic case, accuracy +/-2 percent full scale (ascending). Teflon guide bushings. One reed switch in NEMA 4X/IP66 enclosure. SPDT 3W, 0.25 Amp, 125 VAC/VDC (standard) (switch adjustable range of 15-90 percent).

Manufacturer: Dwyer Instruments Brand: Dwyer Model: 616WL-22

The Series 616WL Differential Pressure Transmitter senses very low pressures of air and non-combustible, compatible gases and sends a standard 4-20 mA output signal. All models, including those featuring the 3 digit LCD digital read-out, are factory calibrated to specific ranges as listed in the chart below. Positive, negative and differential pressures can be measured within a full span accuracy of ±0.50%. This weatherproof unit is enclosed in a polycarbonate case, designed to meet (IP66/NEMA 4X). Internal digital push button zero and span allow for quick and simple field calibration.

Manufacturer: Dwyer Instruments Brand: Dwyer Model: 4300-1KPA

The Dwyer Capsuhelic series 4000 differential pressure gauge with an aluminum case has a circular 4" (100 mm) dial, and four female 1/4" NPT rate connections, and measures pressure with single scale in inch water column (WC), mm WC, cm WC, psid, or kPa with a display accuracy of + or - 3 or 4%. The die-cast aluminum case with impregnated hard coating is for measuring air and compatible gases and oil-based liquids. The circular dial is 4" in diameter and measures pressure with a single scale in inch water column (WC), mm WC, cm WC, psid, or kPa. The pressure being measured is held within a capsule in the gauge, which permits the use of the gauge on system pressures of up to 500 psig, even with differentials less than 0.1 in WC. The gauge accuracy is + or - 3% of full scale at 70 degrees F (21.1 degrees C) with + or - 4% of full scale on some models. The pressure limits are -20" Hg. to 500 psig. The temperature limit is 20 to 200 degrees F (-6.67 to 93.3 degrees C). Four female connections with 1/4" NPT (National Pipe Thread) rate provide for vertical mounting of the gauge. The connections are paired with one high and low pressure pair of taps on top for air and gas and one high and low pressure pair on bottom for liquids. This gauge is suitable as a readout device when measuring flowing fluids, pressure drop across filters, liquid levels in storage tanks, and other applications involving pressure, vacuum, or differential pressure. The gauge comes with two 1/4" NPT plugs for duplicate pressure taps, four flush mounting adapters with screws, and four surface mounting screws.Pressure gauges are instruments used to measure the pressure of a gas or liquid inside a vessel and, often, to help ensure the optimal amount of pressure for a given application. Pressure gauges can range from everyday instruments, such as those used to measure the air pressure in a car or bicycle tire, to highly accurate gauges used in mechanical and industrial processing. Most often, pressure gauges measure pressure relative to another referenc...

Manufacturer: Dwyer Instruments Brand: Dwyer Model: 4300-500PA

The Dwyer Capsuhelic series 4000 differential pressure gauge with an aluminum case has a circular 4" (100 mm) dial, and four female 1/4" NPT rate connections, and measures pressure with single scale in inch water column (WC), mm WC, cm WC, psid, or kPa with a display accuracy of + or - 3 or 4%. The die-cast aluminum case with impregnated hard coating is for measuring air and compatible gases and oil-based liquids. The circular dial is 4" in diameter and measures pressure with a single scale in inch water column (WC), mm WC, cm WC, psid, or kPa. The pressure being measured is held within a capsule in the gauge, which permits the use of the gauge on system pressures of up to 500 psig, even with differentials less than 0.1 in WC. The gauge accuracy is + or - 3% of full scale at 70 degrees F (21.1 degrees C) with + or - 4% of full scale on some models. The pressure limits are -20" Hg. to 500 psig. The temperature limit is 20 to 200 degrees F (-6.67 to 93.3 degrees C). Four female connections with 1/4" NPT (National Pipe Thread) rate provide for vertical mounting of the gauge. The connections are paired with one high and low pressure pair of taps on top for air and gas and one high and low pressure pair on bottom for liquids. This gauge is suitable as a readout device when measuring flowing fluids, pressure drop across filters, liquid levels in storage tanks, and other applications involving pressure, vacuum, or differential pressure. The gauge comes with two 1/4" NPT plugs for duplicate pressure taps, four flush mounting adapters with screws, and four surface mounting screws.Pressure gauges are instruments used to measure the pressure of a gas or liquid inside a vessel and, often, to help ensure the optimal amount of pressure for a given application. Pressure gauges can range from everyday instruments, such as those used to measure the air pressure in a car or bicycle tire, to highly accurate gauges used in mechanical and industrial processing. Most often, pressure gauges measure pressure relative to another referenc...

Manufacturer: Dwyer Instruments Brand: Dwyer Model: MP-010

Differential pressure switch/gage combines the time proven Minihelic II differential pressure gage with two SPDT switching set points. The Mini-Photohelic switch/gage is designed to measure and control positive, negative, or differential pressures consisting of non-combustible and non-corrosive gases. Gage reading is independent of switch operation. Switching status is visible by LED indicators located on the front and rear of the gage. Set points are adjusted with push buttons on back of unit. This extremely compact switch/gage is ideal for fume hoods, dust collection, pneumatic conveying and clean room applications.

Manufacturer: Honeywell, Inc. Brand: Honeywell

P7640B1024, Honeywell, Inc., Differential Pressure Sensor, Duct Mount, With Display

Manufacturer: Dwyer Instruments Brand: Dwyer Model: ISDP-012

The ISDP Differential Pressure Transmitter provides a 4-20 mA process output, a robust NEMA 4X enclosure, plus a large LCD display that can be programmed to read in pressure, velocity or flow. The ISDP offers simplified programming via a Menu key that enables the user to select: security level; English or Metric engineering units; pressure, velocity or flow operation, K-factor for use with various Pitot tubes and flow sensors, circular or rectangular duct size for volumetric flow operation plus many more. The Series ISDP Differential Pressure Transmitter is powered on its two wire loop with 10-35 VDC via its integral M-12 four pin male connector. The ISDP provides a 0.5% full scale accuracy on ranges from 0.25" WC to 100" WC as well as bi-directional models up to 10" WC These features make the Series ISDP Differential Pressure Transmitter the ideal instrument for monitoring pressures or air flows in hazardous zones having a Class I Div. I Groups A, B, C, D; Class II Div. I Groups E, F, G; Class III Div. I ratings.

Manufacturer: Mid-West Instrument Brand: Mid-West Instrument Model: 142-AA-00-OO

Mid-West Instrument diaphragm type differential pressure gauge. Weather resistant construction standard. Over range protection to full rated working pressure. Shatter resistant acrylic lens. Ideally suited for use on dissimilar fluids and wet gas or fluids with a high concentration of solids. Five year limited warranty. Total separation of high and low pressures by a Convoluted Elastomer Diaphragm. Sensor magnetically coupled to the indicating pointer and optional switches. Common applications: filter/strainer monitoring, compressed air, hydraulic, refrigerant, pump performance testing, heat exchanger pressure drop monitoring, water treatment applications, tank level monitoring horizontal or vertical, flow monitoring and balancing. Two times rated working pressure at ambient temperature. Aluminum body material. 316 Stainless steel internal metal part. Buna-N seal material. 1/4-inches FNPT back connections, 2-1/2-inches uni-directional round dial, weather resistant engineered plastic case, accuracy +/-2 percent full scale (ascending). Teflon guide bushings.

Manufacturer: Edge On Up Brand: Sharp Check

PT50A - Industrial... The PT50A is our PT50 Series crossover product with the industrial world. It is the only PT50 Series product that is warranted for commercial/industrial use (3 years). The PT50A features a heavy steel measurement platform, an industrial strain sensor, our fastest processor and 1 gram of resolution. The PT50A is a very versatile product. While it is rated for up to 3000 gram loads it will very accurately measure laboratory edges that measure only a few grams. This portable and lightweight design has already found it's way onto factory, hospital, and laboratory floors across the US. The basic PT50A package includes both our Aluminum Test Fixture and our Disposable Clip system (Test clips have not yet received full BESS certification) giving manufacturers, and those sharpeners who will have only the best, maximum latitude in measuring both standard and non-standard cutting tools and edges.