Differential Pressure Gauges - Page 41

Manufacturer: TechnologyLK Brand: TechnologyLK

Push-Pull capability. Range is from 0-35 Pounds Door Pressure Gauge Push-Pull instrument design specifically to measure force. This instrument is capable of measuring the entire range of forces found in servicing interior and exterior doors. OPERATING INSTRUCTIONS Set the top (small) o-ring located on the plunger rod on zero, down against the instrument's flange; or set the o-ring on the desired force. Holding the instrument firmly, press slowly against the door at a point approximately handle-high, and 30 inches away from the door's hinges. Read the amount of force required to open the door on the plunger scale closest to the bottom of the small o-ring. MEET ADA REQUIREMENTS The Americans with Disabilities Act requires that both interior and exterior doors of a building be handicapped accessible. Door Opening Force (4.1311 ADA AG). Exterior hinged doors:(Reserved) Interior hinged doors:5 lbs (22.2N) Sliding or folding doors:5 lbs (22.2N) Automatic/Power Assisted Doors:(4.13.12) Such doors shall not open to back check faster than 3 seconds and shall require no more than 15 lbs (66.6N) to stop door movement. If a power assisted door is used, its door-opening force shall comply with 4.13.11 and its closing shall conform to the requirements in ANSI A156.19-1984. Plastic Protective Tube for Door Pressure Gauge. Size:8" long 7/8" diameter Includes: Three Door Pressure Gauge Push-Pull, 0-35 Lbs Three Plastic Protective Tube

Manufacturer: Mid-West Instrument Brand: Mid-West Instrument Model: 142-SC-00-OO

Mid-West Instrument diaphragm type differential pressure gauge. Weather resistant construction standard. Over range protection to full rated working pressure. Shatter resistant acrylic lens. Ideally suited for use on dissimilar fluids and wet gas or fluids with a high concentration of solids. Five year limited warranty. Total separation of high and low pressures by a Convoluted Elastomer Diaphragm. Sensor magnetically coupled to the indicating pointer and optional switches. Common applications: filter/strainer monitoring, compressed air, hydraulic, refrigerant, pump performance testing, heat exchanger pressure drop monitoring, water treatment applications, tank level monitoring horizontal or vertical, flow monitoring and balancing. Two times rated working pressure at ambient temperature. 316 Stainless steel body material. 316 Stainless steel internal metal part. Buna-N seal material. 1/4-inches FNPT back connections, 4-1/2-inches uni-directional round dial, weather resistant engineered plastic case, accuracy +/-2 percent full scale (ascending). Teflon guide bushings.

Manufacturer: Mid-West Instrument Brand: Mid-West Instrument Model: 120-AA-00-O(CA)

Mid-West Instrument piston type differential pressure gauge. Simple, rugged, compact design. Over-range protection to maximum pressure. Weather resistant construction standard. Shatter resistant acrylic lens. A low cost differential pressure gauge for use in measuring the pressure drop across filters, strainers, separators, valves, pumps, chillers, etc., and for local flow indication and control. Proof pressure: two times rated working pressure at ambient temperature. Aluminum body material. Stainless steel internal metal part. Buna-N seal material. 1/4-inches FNPT back connections, 2-1/2-inches uni-directional round dial, weather resistant engineered plastic case, accuracy +/-2 percent full scale (ascending). One switch in standard enclosure with 1/4-inches FNPT electrical connection NEMA 4X. SPDT 3W, 0.25 Amp, 125 VAC/VDC (standard) (switch adjustable range of 10-90 percent).

Manufacturer: Dwyer Instruments, Inc. Brand: Dwyer

6685, Dwyer Instruments, Inc., DIFFERENTIAL PRESSURE

Manufacturer: Mid-West Instrument Brand: Mid-West Instrument Model: 142-AA-00-OO

Mid-West Instrument diaphragm type differential pressure gauge. Weather resistant construction standard. Over range protection to full rated working pressure. Shatter resistant acrylic lens. Ideally suited for use on dissimilar fluids and wet gas or fluids with a high concentration of solids. Five year limited warranty. Total separation of high and low pressures by a Convoluted Elastomer Diaphragm. Sensor magnetically coupled to the indicating pointer and optional switches. Common applications: filter/strainer monitoring, compressed air, hydraulic, refrigerant, pump performance testing, heat exchanger pressure drop monitoring, water treatment applications, tank level monitoring horizontal or vertical, flow monitoring and balancing. Two times rated working pressure at ambient temperature. Aluminum body material. 316 Stainless steel internal metal part. Buna-N seal material. 1/4-inches FNPT back connections, 2-1/2-inches uni-directional round dial, weather resistant engineered plastic case, accuracy +/-2 percent full scale (ascending). Teflon guide bushings.

Manufacturer: Ashcroft Brand: Ashcroft

Gauge is ideal for use where ambient corrosion is a concern. Designed with stainless steel case and ring that offers excellent resistance to chemical, weather, and corrosion attack. This listing is for each. Technical Specification Item Differential Pressure Gauge Differential Pressure Range 0 to 25 H2O Rated Total Pressure 35 psi Connection Size 1/8 NPT Dial Size 4-1/2 Body Material Glass Filled Nylon Scale Type Pressure Pressure Range Minor Div. 0.50 H2O Relay Type SPDT Accuracy +/-3% Contact Rating 0.25A @ 175VAC/DC Dial Material Stainless steel Diaphragm Material Buna-N Piston Material Teflon Seal Material Buna-N Ambient Operating Range 0 Degrees to 140 Degrees F Includes Instructions Manufacturers Warranty Length 5 yr.

Manufacturer: Ashcroft Inc. Brand: Ashcroft Model: 351132FD25SXCYLM25IW

The Type 1132 uses a convoluted diaphragm design with no migration of the process media. It is recommended for lower differential and high static pressures, up to 1500 psi.Body materials are available in Aluminum, Brass and Stainless Steel, with Buna,Viton or EPDM seals

Manufacturer: Dwyer Instruments Brand: Dwyer Model: MP-25MM

Differential pressure switch/gage combines the time proven Minihelic II differential pressure gage with two SPDT switching set points. The Mini-Photohelic switch/gage is designed to measure and control positive, negative, or differential pressures consisting of non-combustible and non-corrosive gases. Gage reading is independent of switch operation. Switching status is visible by LED indicators located on the front and rear of the gage. Set points are adjusted with push buttons on back of unit. This extremely compact switch/gage is ideal for fume hoods, dust collection, pneumatic conveying and clean room applications.

Manufacturer: Dwyer Instruments Brand: Dwyer Model: 616D-14

The Series 616D Differential Pressure Transmitter senses the pressure of air and compatible gases and sends a standard 4-20 mA output signal. The 616D housing is specifically designed to mount on a 35 mm DIN rail in a panel. This mounting style allows for several units to be mounted closely together reducing required space. A wide range of models are available factory calibrated to specific ranges. The span and zero controls are for use when checking calibration. They are not intended for re-ranging to a significantly different span. Versatile circuit design enables operation in 2-wire current loops.

Manufacturer: Mid-West Instrument Brand: Mid-West Instrument Model: 142-AC-00-OO

Mid-West Instrument diaphragm type differential pressure gauge. Weather resistant construction standard. Over range protection to full rated working pressure. Shatter resistant acrylic lens. Ideally suited for use on dissimilar fluids and wet gas or fluids with a high concentration of solids. Five year limited warranty. Total separation of high and low pressures by a Convoluted Elastomer Diaphragm. Sensor magnetically coupled to the indicating pointer and optional switches. Common applications: filter/strainer monitoring, compressed air, hydraulic, refrigerant, pump performance testing, heat exchanger pressure drop monitoring, water treatment applications, tank level monitoring horizontal or vertical, flow monitoring and balancing. Two times rated working pressure at ambient temperature. Aluminum body material. 316 Stainless steel internal metal part. Buna-N seal material. 1/4-inches FNPT back connections, 4-1/2-inches uni-directional round dial, weather resistant engineered plastic case, accuracy +/-2 percent full scale (ascending). Teflon guide bushings.