Viscometers - Page 67

Manufacturer: Cannon Instrument Brand: CANNON Instrument

Similar to Cannon-Ubbelohde but less rugged in design. Includes instruction sheet. Minimum sample volume: 11 mL. Require bath depth of 241 mm (9.5"). See Table 2 (preceding 9721A50) for constants and ranges. Individually boxed. Calibrated viscometers are supplied with a certificate of calibration and instruction sheet. Viscometers have the serial number and size printed on the outside of the box and on the viscometer. Holder is not supplied. For holders, see Thomas number 9726M82.

Manufacturer: Cannon Instrument Brand: CANNON Instrument

Reverse-flow type, for measurement of kinematic viscosity of dark Newtonian liquids according to ASTM D 445 and ISO 3104. Permit measurements of liquids whose meniscus cannot be seen at the timing marks when using Cannon-Fenske Routine-type viscometer. Used to measure kinematic viscosity of liquid (cutback) asphalts and road oils at 60°C (140°F) in range of 30 to 6000 centistokes according to ASTM D 2170. Also used to study lubricating oils at low temperatures when investigating the effect of various additives on lubricating and hydraulic oils. External pressure can be applied to vary shear stress and shear rate. cifications conform to ASTM D 446 and ISO 3105.

Manufacturer: PUSHEN Brand: PUSHEN Model: DIN NO.4

Product Description: Applicable to the construction site to quickly measure the viscosity of the paint to be sprayed; more widely used in electronic products, plastic coatings industry. The cup and Iwata spray gun together become essential plant construction tools. The main technical parameters: nozzle hole diameter: Φ4 mm Range of measurment：96-683 cSt Efflux time (in seconds) :20-110 s Usage: 1:using a suitable solvent to wipe clean， when before or after the cup be used。 2:put the cup into the container body 1- 5 minutes, to achieve thermal equilibrium of the cup body,then put the cup body vertical lift from the feedstock, the action should be fast and stable. 3:Timekeeping when the upper end of the cup leave from the surface of Liquid， and liquid should be kept out of the cup vertically, with the surface distance of not more than 150mm. 4 :Stop timing when the first breakpoint occurs, and the difference between the two measured values should be less than 5% of the average. NOTE: Please give us your phone number which is to ensure a smooth and safe delivery. And we can also send the product to you as soon as possible If you have any questions , please feel free to contact us

Manufacturer: YSY10Ï€Cyanalab Shop Brand: KUNHEWUHUA

Model: cp-2c product characteristics Ideal for drilling holes in glass and plastic lenses. Opposing taper drill bits system allow holes to be drilled from both sides simultaneously for precision placenent and avoids chipping and breaking of all lenses ,especially those made of resin, After hole drilled,placed the lens under reamer and lifted upwards to be enlarged to desired size. Technicel parameters Dimensions (LXWXH) : 150X120X300mm Weight : 4kg Power Requirement :110/220v 60hz/50hz AC 600W NOTE: we have both 110V version and 220V version for this item, please kindly which one do you need so we can arrange the shipment as soon as possible, thank you! If you do not leave a message to us, we will ship the item as your country's standard voltageNOTE: we have both 110V version and 220V version for this item, please kindly which one do you need so we can arrange the shipment as soon as possible, thank you! If you do not leave a message to us, we will ship the item as your country's standard voltageHeadling time：4days you will receive it within 5-9 working days.

Manufacturer: PAUL N. GARDNER CO. INC. Brand: Gardco Model: EZ2

The EZ cup formula for each cup of the series matches the applicable ASTM formula in D 4212 at the recommended calibration level. EZ Cups are compatible to ASTM D 1084 Viscosity of Adhesives and ASTM D 816. Conversion tables that relate to drain time in seconds (to the nearest tenth second) to viscosity in centistokes are furnished with each EZ Cup. EZ Cup calibration is traceable to NIST. Calibration and Certification procedures qualify under MIL STD 45662A, ISO 9002. The EZ Cup is not matched by any other cup of its type, with respect to the advantages listed above, in quality of workmanship or in continuing quality control procedures. The finest, most reliable, calibrated and documented cup on the market.

Manufacturer: Cannon Instrument Brand: CANNON Instrument

Specifications conform with ASTM Standard D 446. Minimum sample volume: 1.0 mL. Sizes 400 through 600 may require more sample. Require liquid bath depth of 200 mm. Constants and ranges are as given in Table 1 preceding 9721A50. Individually boxed, with certificate of calibration and instruction sheet.

Manufacturer: Cannon Instrument Brand: CANNON Instrument

Specifications conform with ASTM Standard D 446. Minimum sample volume: 1.0 mL. Sizes 400 through 600 may require more sample. Require liquid bath depth of 200 mm. Constants and ranges are as given in Table 1 preceding 9721A50. Individually boxed, with certificate of calibration and instruction sheet.

Manufacturer: Cannon Instrument Brand: CANNON Instrument

The Cannon-Ubbelohde CUU-500 uncalibrated viscometer has a 1,600 to 8,000 centistokes (cSt) viscosity measuring range and is suitable for the measurement of transparent Newtonian fluids such as fuels and lubricants. It uses a viscometer constant of 8.0 centistokes per second (cSt/s) for calculating kinematic viscosity. The CUU-series size 500 viscometer uses a 254mm depth water bath (not included) for temperature-control testing and a vacuum (not included) to draw a sample up for timed testing between two sets of printed marks. This uncalibrated viscometer is suited for use at temperatures above 93 degrees C (200 degrees F) or below -18 degrees C (0 degrees F) and meets the ASTM International D445 standard for testing viscosity. A viscometer, also called a viscosimeter, is an instrument used to measure the friction caused by the relative motion of a Newtonian fluid and a known surface, and is usually expressed in units of poise (P), centipoise (cP), pascal seconds (Pa s), and millipascal seconds (mPa s). Viscometers have several forms, including but not limited to falling ball, rotational, vibrating, capillary, funnel, and bubble. A falling ball viscometer measures the time it takes for a ball of known diameter and density to fall through fluid in a cylinder of known diameter. A rotational viscometer measures the force required to stir a fluid. A vibrating viscometer measures the power input necessary to keep the oscillator vibrating at constant amplitude while immersed in a fluid. A capillary viscometer has a narrow-bore vertical section with two printed marks that measure time required for a known volume of fluid to fall a known distance. A funnel viscometer, such as a Ford, Zahn, or Shell cup, measures the time it takes a known volume of fluid to flow from the base of a cone through a short tube. A bubble viscometer measures the time required for an air bubble to rise through a fluid. Viscosity measurements are used in laboratories, research and development, process control, and plant quality control applicat...

Manufacturer: Cannon Instrument Brand: CANNON Instrument

For measurement of kinematic viscosity of transparent Newtonian liquids by suspended level principle as described in ASTM D 445 and D 446, and ISO 3104 and 3105. Similar to Cannon-Ubbelohde but less rugged n design. Provided with certificate of calibration and instruction sheet

Manufacturer: Cannon Instrument Brand: CANNON Instrument

The Cannon-Manning CMVC-12 vacuum-calibrated viscometer has a 360 to 8,000 poise (P) viscosity measuring range and is suitable for the measurement of highly viscous materials such as asphalt at 140 degrees F. The CMVC-series size 12 viscometer uses a water bath (not included) for temperature-control testing, and a 300mm Hg vacuum (not included) to draw a sample up for timed testing between two sets of printed marks. This vacuum-calibrated viscometer meets the ASTM International D2171 standard for testing asphalt viscosity. A viscometer, also called a viscosimeter, is an instrument used to measure the friction caused by the relative motion of a Newtonian fluid and a known surface, and is usually expressed in units of poise (P), centipoise (cP), pascal seconds (Pa s), and millipascal seconds (mPa s). Viscometers have several forms, including but not limited to falling ball, rotational, vibrating, capillary, funnel, and bubble. A falling ball viscometer measures the time it takes for a ball of known diameter and density to fall through fluid in a cylinder of known diameter. A rotational viscometer measures the force required to stir a fluid. A vibrating viscometer measures the power input necessary to keep the oscillator vibrating at constant amplitude while immersed in a fluid. A capillary viscometer has a narrow-bore vertical section with two printed marks that measure time required for a known volume of fluid to fall a known distance. A funnel viscometer, such as a Ford, Zahn, or Shell cup, measures the time it takes a known volume of fluid to flow from the base of a cone through a short tube. A bubble viscometer measures the time required for an air bubble to rise through a fluid. Viscosity measurements are used in laboratories, research and development, process control, and plant quality control applications. Some viscometers are manufactured to meet industry or governmental standards, including Ingress Protection (IP), National Institute of Standards and Technology (NIST), International Standards Organization...