Dial Calipers - Page 13

Manufacturer: MEDA - SUPERIOR IMPORT Brand: Meda - Superior Import

• For measuring inside diameters, recesses, etc. • Can be set with a micrometer or ring gage. • Graduated in .001". • Arms automatically open and close at the touch of a button. • Supplied in a fitted case.

Manufacturer: Starrett Brand: Starrett Model: 1202F-6 Color: White

The Starrett 1202F-6 dial caliper measures 0 to 6 inches with 0.01” and 1/64” accuracy. This handy measuring tool allows for reliable and accurate depth, inside, and outside readings with the sharp, black graduations on the no-glare, satin-finished bar, crisp lines on the dial face, and knife edge contacts on the jaws. The dial’s inner, decimal scale is white, while the outer, fractional scale is yellow. One full revolution of the dial is equivalent to 0.100”. The knife-edge contacts can be used to scribe parallel lines on the workpiece. This caliper can be used with one hand through operating the fine adjustment roll with the thumb. The lock screw locks the dial bezel and holds the sliding jaw in position. The depth rod is integrated into the rack of the caliper, unlike many calipers which offer a detachable depth rod, or none at all. The hardened stainless steel components, including the bar, measuring surfaces, rack, gears, and depth rod, offer corrosion resistance, increased accuracy, and long life. Positive double pinion anti-backlash control offers increased accuracy over standard gear configurations. Backlash is the amount of clearance between mated gear teeth in the caliper controls – which prevents the gear teeth from jamming. It is undesirable to have much backlash due to the lack of precision offered by the increased amount of play between gears. Certain gear designs can minimize or eliminate backlash. Double pinion anti-backlash systems have two round gears (also called pinions) in contact with the rack gear that extends down the length of the caliper itself. The two pinions have a lower chance of disengaging with the rack gear than a single gear, thereby keeping the caliper more accurate than a single gear anti-backlash system. The rack teeth point down to keep foreign matter from clogging the gear operations. This prevents measurement errors where metal chips could interfere with proper caliper operation. Calipers measure the distance between two opposing sides of a...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 505-742-55

Mitutoyo 505-742-55 D6"Tx-5, Caliper, Dial, Orange Face,.1"/Rev, 0-6",.001".

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 505-675-56 Color: Black

The Mitutoyo 505 series dial caliper uses a combination of a vernier scale and a dial whose pointer travels one rotation for each 0.1” measured to perform precise outside diameter (OD), inside diameter (ID), depth, and step measurements. The dial caliper has a fixed (main) scale and a movable dial, unlike the vernier caliper which has a second, movable vernier scale. The dial is circular and has a pointer; it is mounted on a toothed gear track which drives the pointer. As the dial moves over the main scale rule, the pointer rotates once to give the additional fractional reading. The second measurement is added to the main scale reading to obtain a final result accurate to the smallest graduation marked on the dial. The main scale and dial are marked in inches. The dial can be rotated beneath the pointer to measure size differential between two objects. The dial caliper is easier to read than the vernier caliper, thus safeguarding against user reading errors. Its standard of precise measurement complements the use of the vernier caliper; the dial provides an ease in reading and interpolating measurements which most vernier calipers, due to their need for direct observation of both scales, may not provide. The dial uses a rack-and-pinion mechanism and is mounted on a gear track where each tooth equals one quarter of the dial revolution, and four teeth equal 0.1”. The smooth-moving dial is graduated to 0.001” and offers gear train shock protection. A thumbwheel permits fast operation with one hand. A clamping screw controls scale movement and a dial calibration lock holds the sliding jaw’s position. The caliper is made of hardened stainless steel construction with titanium nitride (TiN) coating on the beam wear surface helps extend caliper life. Two sets of jaws provide four-way measurement capability: outside dimension (OD), inside dimension (ID), depth, and step, where the butt end of the fixed jaw measures one end of a work piece before its upper/lower or inner/outer steps are measured....

Manufacturer: Hexagon Metrology Brand: Brown & Sharpe Color: Yellow

The Brown & Sharpe TESA CCMA dial caliper has an accuracy of 100mm, a 32mm diameter rotating dial with a yellow face and lock screws, is made of stainless steel, and measures in metric. The covered rack helps prevent measurement error by protecting the gear from foreign matter. Linear accuracy meets Deutsches Institut für Normung (DIN) 862 standards. These calipers are for use in taking inside dimensions (ID), outside dimensions (OD), depth, and step measurements. The bezel lock screw locks the dial and the slider lock screw holds the sliding jaw in position. The hardened stainless steel components, including the bar, measuring surfaces, and gears, offer corrosion resistance, increased accuracy, and long life. Spring anti-backlash control offers increased accuracy over standard gear configurations. Backlash is the amount of clearance between mated gear teeth in the caliper controls, which prevents the gear teeth from jamming. It is undesirable to have much backlash due to the lack of precision offered by the increased amount of play between gears. Certain gear designs can minimize or eliminate backlash; spring anti-backlash systems use a spring to add a compressive force, thereby minimizing backlash. Calipers measure the distance between two opposing sides of an object. They make inside, outside, depth, or step measurements, according to their type. Calipers are commonly used in architecture, metalworking, mechanical engineering, and machining. The simplest calipers have two legs to mark the two points and require a ruler to take the measurement. More complex calipers use two sets of jaws instead of legs and have up to two graduated scales. Vernier, dial, and digital calipers give direct and accurate readings and are functionally identical, having a calibrated scale with a fixed jaw, and another jaw with a movable pointer that slides along the scale. The vernier caliper has a scale sliding parallel to the main scale for an additional, fractional reading to improve measurement precision. The dial caliper has a ...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 505-675-52 Color: Purple

The Mitutoyo 505 series dial caliper uses a combination of a vernier scale and a dial whose pointer travels one rotation for each 0.1” measured to perform precise outside diameter (OD), inside diameter (ID), depth, and step measurements. The dial caliper has a fixed (main) scale and a movable dial, unlike the vernier caliper which has a second, movable vernier scale. The dial is circular and has a pointer; it is mounted on a toothed gear track which drives the pointer. As the dial moves over the main scale rule, the pointer rotates once to give the additional fractional reading. The second measurement is added to the main scale reading to obtain a final result accurate to the smallest graduation marked on the dial. The main scale and dial are marked in inches. The dial can be rotated beneath the pointer to measure size differential between two objects. The dial caliper is easier to read than the vernier caliper, thus safeguarding against user reading errors. Its standard of precise measurement complements the use of the vernier caliper; the dial provides an ease in reading and interpolating measurements which most vernier calipers, due to their need for direct observation of both scales, may not provide. The dial uses a rack-and-pinion mechanism and is mounted on a gear track where each tooth equals one quarter of the dial revolution, and four teeth equal 0.1”. The smooth-moving dial is graduated to 0.001” and offers gear train shock protection. A thumbwheel permits fast operation with one hand. A clamping screw controls scale movement and a dial calibration lock holds the sliding jaw’s position. The caliper is made of hardened stainless steel construction with titanium nitride (TiN) coating on the beam wear surface helps extend caliper life. Two sets of jaws provide four-way measurement capability: outside dimension (OD), inside dimension (ID), depth, and step, where the butt end of the fixed jaw measures one end of a work piece before its upper/lower or inner/outer steps are measured....

Manufacturer: Moore and Wright Brand: Moore & Wright Model: 4004

Moore and Wright HistoryFounded in 1906 by innovative young engineer Frank Moore, Moore and Wright has been designing, manufacturing and supplying precision measuring equipment to global industry for over 100 years. With roots fixed firmly in Sheffield, England, the company began by manufacturing a range of calipers, screwdrivers, punches and other engineers tools.

Manufacturer: HFS Brand: HFS

1/4" holes for 1/4" stem indicator Product features Two universal ball sockets permit adjustments to any angle or position Fine adjustment clamp Dovetail clamp for test indicator Quickly attaches to any metallic surface

Manufacturer: Steelex Brand: Steelex Model: D1056

Manufacturer: Generic Brand: Generic