Calipers - Page 135

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 505-730

Mitutoyo Caliper, Dial, 2 mm/Rev, 0-150 mm, 0.02 mm.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 505-742-56

Mitutoyo 505-742-56 D6"Tx-6, Caliper, Dial, Black Face,.1"/Rev, 0-6",.001".

Manufacturer: Trim Clip Brand: Trim Clip Model: 003010, 003027

Included: (4) Miter Aids 003010 (4) Miter Clips 003027 Miter Aids Marking and measuring the inside dimension of a mitered piece of casing can be a challenge with no place to hook your tape-especially if the trim piece is long. Not so with the Miter Aid. Simply clip it on with the integral spring clamp, and the Miter Aid provides a slot for your tape measure, perfectly aligned with the inside corner of a 45° miter. No need for an assistant and no need to measure from the one inch mark and subtract. The Miter Aid also provides a handy reveal fence for marking your reveals on the jambs, header and sill. Once the reveals are marked, tap in a pin nail where the inside of the miter will be, hook your tape over the nail, and measure your width and height with ease. If you've ever fumbled with a floppy tape while casing out windows and doors, you'll love the ease and simplicity of the Trim Clip Miter Aid Miter Clips Clamping miters couldn't get much easier than with the Miter Clip. Just position the Miter Clip and squeeze-the reverse cam mechanism applies pressure and holds the miter clamp firmly shut, while the notch keeps the tips of the miters neatly aligned. Once clamped, you can also rotate the clamp handle up and out of the way, providing access so you can nail the miter and move on to the next corner. The metal spurs hold the wood firmly and allow the clamp to be rotated, while leaving minimal marks. Made in the USA.

Manufacturer: Westward Brand: Westward

Precision Measuring Tool Kit, Number of Pieces 2, Micrometer 6 In/150mm Electronic Depth Micrometer w/English, Metric, Fraction Reading, Caliper 6 In/150mm Poly Carbonate Caliper, Reading in English/Metric/Fraction, Includes Digital Caliper, Digital Depth Micrometer, Hardened Case

Manufacturer: Fowler Brand: Fowler

High precision Pin Gage (Plug Gage) sets at very economical prices. Offered in two grades of tolerance: Plus (+.0002 ) ). Fowler Pin Gage Sets come in a range of sizes. These accurate and well made precision tools are ideal for checking hole size, location, gage slots, distance between holes, go sizes etched on ranges over .061 Each gage checked against master gages traceable to the National Institute of Standards and Technology Gages are cylindrical, 2 in length and have no sharp corners Accurate to .0002 Gage increments are in .001 steps

Manufacturer: Generic Brand: Generic

Bottom surface of the base is hardened and ground lapped for flatness

Manufacturer: Hexagon Metrology Brand: Standard Gage Model: 00524105

The Standard Gage 00524105 electronic micrometer and caliper set includes a 0 to 1" outside micrometer, 0 to 6" calipers, and a depth measuring base for making precision measurements. The electronic micrometer has 0.0001" graduations on a chrome steel frame with precision of 0.00016" and an LCD with a numerical resolution of 0.00005". LCD function buttons include metric/inch conversion, zero setting, and origin. It has carbide-tipped measuring faces, a ratcheting friction thimble, and a nut for locking the spindle in place. The electronic calipers have a 0.0005" LCD resolution on a stainless steel frame. The calipers are made of stainless steel and have a thumb roller for adjusting the calipers. The depth measuring base is a T-bar style base that attaches to the calipers' ruled blade to aid depth measurement and is 76.2mm long to span holes and recesses for stable measurements. The calipers linear accuracy meets Deutsches Institut für Normung (DIN) 862 standards and the micrometer is Ingress Protection certified IP54 against dust and liquids. The electronic micrometer and calipers set comes with a fitted storage case and is typically used in manufacturing, machining, and mechanical engineering.SpecificationsMicrometer typeElectronic, outsideMicrometer measurement range0 to 1.0"Micrometer resolution0.00005"/0.001mmMicrometer precision0.00016"Micrometer LCD functionsAutomatic shut-off, metric/inch conversion, zero setting, and originMicrometer protection levelIP54Caliper typeElectronicCaliper measurement range0 to 6.0"Caliper resolution0.0005"Caliper LCD functionsOn/off, metric/inch conversion, and zero settingCaliper standardsDIN 862Digital calipers are measuring instruments commonly used for inspection in manufacturing to provide the precise measurements of an object. A pair of jaws attached to a long beam with a marked scale is used to take inside, outside, and step measurements. An additional depth probe slides along the beam to take depth measurements. One jaw is fixed to the end of the scale, while the ot...

Manufacturer: Aircraft Tool Supply Brand: Aircraft Tool Supply

Complete Precision Electronic Measuring Set includes: 6"Electronic caliper - .0005" (.01mm) resolution w/ patented ceramic chip, 0-1" (0-25mm) Electronic Micrometer - .0005" (.001mm) resolution. Reads directly in inch or metric. Includes fitted case.

Manufacturer: Flexbar Brand: Flexbar

for Checking Outside Diameters, Recess Diameters, etc. Spring loaded Arms and ceramic contact Points for accurate Measurements under constant pressure. Push-button to close Arms. Dial Reading .200" per revolution (2x.100"). Revolution counter. Spring loaded-constant Measuring pressure. Each Caliper has 1" movement. Can be Set With Micrometer or ring Gage. 2" Dial Face Diameter. Length of Arm is 3 1/4". Measuring Anvil length = 13/32". Measuring Anvil Thickness = 3/32". Can be Set With Gage Blocks or Micrometer Standards. includes fitted Case. Model No.18551, External Dial Caliper Gage,375"-1.375" Range.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 209-558

The Mitutoyo 209 series Digimatic internal tube thickness caliper gauge has a combination analog/digital LCD display and large measuring depth for taking inside dimension (ID) measurements of hole diameters, thickness of grooves or tubes, and other hard-to-reach internal dimensions. Depending on the model, these units may come with either ball contact points suitable for measuring internal wall thickness of tubes, or disc contact points suitable for measuring flat surfaces. The calipers have an Ingress Protection 67 (IP67) rating, which ensures that components are resistant to debris and to submersion in liquid under standard conditions for up to 30 minutes. At minimum, functions include zero-set, preset, automatic power off, inch/metric, and conversion data hold. An output port transmits results to a Mitutoyo miniprocessor or computer for statistical process control (SPC) through an interface cable (sold separately). The unit comes with, and is powered by, a single AA battery that lasts approximately 350 hours with continuous normal use. Calipers measure the distance between two opposing sides of an object. They make inside, outside, depth, or step measurements, according to their type. Calipers are commonly used in architecture, metalworking, mechanical engineering, and machining. The simplest calipers have two legs to mark the two points and require a ruler to take the measurement. More complex calipers use two sets of jaws instead of legs and have up to two graduated scales. Vernier, dial, and digital calipers give direct and accurate readings and are functionally identical, having a calibrated scale with a fixed jaw, and another jaw with a movable pointer that slides along the scale. The vernier caliper has a scale sliding parallel to the main scale for an additional, fractional reading to improve measurement precision. The dial caliper has a circular dial with a pointer on a toothed gear rack replacing the second vernier scale. As with the vernier, this second measurement is added to the reading from the m...