Calipers - Page 90

Manufacturer: Generic Brand: Generic

Manufacturer: TwoRay Brand: RayTools

6 Inch Digital Caliper Vernier Gauge Micrometer 150 Mm

Manufacturer: Generic Brand: Generic

Centered (V) Magnet for Strongest Grip on Flat and Round Surfaces~~## Two Magnetic Mounting Surfaces (Bottom and Back)~~## Swivel Adapter for Mounting all AGD Dial Indicators with Lug Back On/Off Switch~~## 7" Center Post and 6" Swing Arm, Diameter of Post is 1/2" ; Fine Adjustment;

Manufacturer: Grizzly Brand: Grizzly Model: G9786

These precision instruments are a must for quickly determining dimensions or location. The 6" Dial Caliper is hardened stainless steel with easy to read dial, stop and thumb wheel. The Micrometer is carbide tipped, has 0.0005" graduations and a vernier scale for ten thousandths of an inch. Last, but certainly not least, the dial test indicator is calibrated 0.0005" and has range of 0.030" and the tip can be repositioned. It comes supplied with a 3/8" and 4mm mounting studs.

Manufacturer: Central Tools Brand: Central Tools Model: 6427

Four measurements; inside, outside, depth and step. This particular dial caliper is made of stainless steel and is stress relieved. Measuring surfaces are precision-ground and lapped. The dial indicator has a fine line indicating hand. It has a very unique and sleek design.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 530-316

The Mitutoyo 530 series vernier caliper has two sets of jaws and a depth bar for four-way measurement in inch and metric units of outside dimension (OD), inside dimension (ID), step, and depth, for applications where the highest accuracy is required, especially in scientific research and in industries where parts must fit exactly. The caliper has a dual vernier scale, with an upper scale measuring in inches and a lower scale measuring in millimeters. A 14-degree vernier face angle improves visibility and helps prevent parallax error in measurement reading. The caliper’s two sets of jaws provide the capability to make OD and ID measurements, as well as step measurements, where the butt end of the fixed jaw measures one end of a work piece before its upper/lower or inner/outer steps are measured. A depth measuring blade with rounded edges provides the ability to make depth measurements. The scales are raised to slide easily and protect the graduation markings. A thumbwheel permits fast and easy measuring. A clamping screw on the upper scale rotates to control scale movement and locks to hold the sliding jaw’s position. The caliper is made of hardened, corrosion-resistant stainless steel with a satin chrome finish that helps reduce glare. The caliper meets Federal Accuracy Specifications GGG-C-111B. Calipers measure the distance between two opposing sides of an object. They make inside, outside, depth, or step measurements, according to their type. Calipers are commonly used in architecture, metalworking, mechanical engineering, and machining. The simplest calipers have two legs to mark the two points and require a ruler to take the measurement. More complex calipers use two sets of jaws instead of legs and have up to two graduated scales. Vernier, dial, and digital calipers give direct and accurate readings and are functionally identical, having a calibrated scale with a fixed jaw, and another jaw with a movable pointer that slides along the scale. The vernier caliper has a scale sliding parallel to...

Manufacturer: SRA Measurement Brand: Machine DRO Model: ME-VT300

The scale is supplied with - slotted mounting brackets that clamp to each end of the scale. These can easily be removed allowing the scale to be cut to any length. Also supplied is a bracket for the rear of the reading head, attached by two M3 screws which are supplied.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 530-114

The Mitutoyo 530 series vernier caliper has two sets of jaws and a depth bar for four-way measurement in inch and metric units of outside dimension (OD), inside dimension (ID), step, and depth, for applications where the highest accuracy is required, especially in scientific research and in industries where parts must fit exactly. The caliper has a dual vernier scale, with an upper scale measuring in inches and a lower scale measuring in millimeters. A 14-degree vernier face angle improves visibility and helps prevent parallax error in measurement reading. The caliper’s two sets of jaws provide the capability to make OD and ID measurements, as well as step measurements, where the butt end of the fixed jaw measures one end of a work piece before its upper/lower or inner/outer steps are measured. A depth measuring blade with rounded edges provides the ability to make depth measurements. The scales are raised to slide easily and protect the graduation markings. A thumbwheel permits fast and easy measuring. A clamping screw on the upper scale rotates to control scale movement and locks to hold the sliding jaw’s position. The caliper is made of hardened, corrosion-resistant stainless steel with a satin chrome finish that helps reduce glare. The caliper meets Federal Accuracy Specifications GGG-C-111B. Calipers measure the distance between two opposing sides of an object. They make inside, outside, depth, or step measurements, according to their type. Calipers are commonly used in architecture, metalworking, mechanical engineering, and machining. The simplest calipers have two legs to mark the two points and require a ruler to take the measurement. More complex calipers use two sets of jaws instead of legs and have up to two graduated scales. Vernier, dial, and digital calipers give direct and accurate readings and are functionally identical, having a calibrated scale with a fixed jaw, and another jaw with a movable pointer that slides along the scale. The vernier caliper has a scale sliding parallel ...

Manufacturer: Brand new Brand: Brand new

Features: Super Large Dial Pocket Style (2" x 2-3/4" x 3/4"). Metal Construction Graduation 0.001" Accuracy 0.001" Maximum Measuring Depth 1/2" Adjustable gauge for dead zero setting. Fitted storage case included. Thumb slider operation, spring loaded. 1 Year Manufacturer Warranty.

Manufacturer: Fred V. Fowler Company, Inc. Brand: Fowler Model: 52-222-204-0

The Fowler EZ-Read steel digit micrometer has a choice of measurement range and a flat anvil/spindle pair for general purpose measuring. The digit display has 0.0001" graduation intervals and an accuracy of 0.0002" for precise readings. Carbide-tipped measuring faces provide wear resistance. A friction thimble provides smooth and quiet operations, and is suitable for one-handed operation. Friction-style thimbles stop turning when the spindle comes into contact with the workpiece, providing constant force for consistent measurements between operators. The insulated steel frame helps reduce temperature-related expansion or contraction providing for accurate measurements. The micrometer includes a wrench and fitted case. Micrometers 2" and above include a standard. SpecificationsDisplay type Digit Anvil/spindle style Flat Measuring range Varies Graduation Interval 0.0001" Accuracy 0.0002" Thimble style FrictionMicrometers are precision measuring instruments that use a calibrated screw to measure distances. These measurements are translated into large rotations of the screw that are then able to be read from a scale or a dial. Micrometers are typically used in manufacturing, machining, and mechanical engineering. There are three types of micrometer: outside, inside, and depth. Outside micrometers may also be called micrometer calipers, and are used to measure the length, width, or outside diameter of an object. Inside micrometers are typically used to measure interior diameter, as in a hole. Depth micrometers measure the height, or depth, of any shape that has a step, groove, or slot.The Fred V. Fowler Company manufactures inspection and measurement instruments such as electronic indicators, calipers, bore gages, and digital scales. The company, founded in 1946, is headquartered in Newton, MA.What’s in the Box? Fowler Steel EZ-Read Outside Digit Micrometer Standard (for sizes 2" and above)Wrench Fitted case