Current Testers - Page 203

Manufacturer: Acr Electronics Brand: Blue Sea Systems

Shunt type: 50 millivolts at meter full scale;Meter operating current: 1 milliampere at full scale;Integral backlight for low-light readability;Dimensions: 2.375 x 2.800

Manufacturer: Johnson / Emerson Connectivity Solutions Brand: Johnson / Emerson Connectivity Solutions

Test Plugs & Test Jacks BANANA PLUG RED

Manufacturer: Hioki Brand: Hioki Model: 9635-01

Voltage lead. For clamp on power HiTester. 1 Year warranty>

Manufacturer: IDI Brand: IDGroup

Contact Probes HEADED SERRATED

Manufacturer: Mueller Electric Brand: Mueller Electric

Test Clips Red Micro-Plgr Clip-

Manufacturer: Vetus Brand: ETCR

Technical Specification *Function AC leakage measurement, AC current measurement, On-line AC current measurement *Power Supply 6F22,9V *Process Type Clamp CT, Integral Approach *Display Type 4 Digits LCD *Clamp Size 25mm×30mm *Meter Dimension LWH: 175mm×70mm×38mm *LCD Dimension 35mm×21.5mm; Display Dimension: 32mm×15mm *Sampling Rate 2 Times/Second *Frequency 50Hz, 60Hz Automatic identification *Shifting Automatic Shift *Range :0.001mA～60.00A *Resolution: 1uA *Accuracy :±1.5%±5dgt (23℃±3℃, below 70%RH) *Line voltage : Below AC 600V *RS232 Interface: With RS232 interface, Data stored in the memory can be uploaded to the computer, with software monitoring *Data Memory : 99 sets, "FULL" Blinking when memory is full *Peak Maintaining Peak value capture hold function, press HOLD without Release to display peak value *Reading Hold Reading hold function: "DH" symbol display *Overflow display Range overflow function: "OL" symbol display *Automatic Shutdown :5 minutes after the boot *Battery Detection :When battery voltage is lower than 7.2V, low battery symbol will shown to remind battery replacement. *Rated Power : 5mW *Working Temperature and Humidity: 0℃~40℃; below 80%rh *Storage Temperature and Humidity :-10℃~60℃; below 70%rh *Insulation Strength :AC2kV/rms (between core and box) *Safety Provisions: IEC1010-1, IEC1010-2-032, Pollution level 2, CAT Ⅲ(600V) *Accessories Meter: 1 piece, RS232 Com-cable:1 piece; Software Disk: 1 piece;

Manufacturer: Hioki Brand: Hioki Model: 9650

Clamp on sensor for the micro hicorder 8205-10/8206-10. Sensor is designed with a safety barrier to protect the user from being in direct contact with live conductors. Completely meet all CE marking requirements. Rated input current 100 A AC. Rated output current 100 mA AC. Accuracy (at 50/60 Hz) amplitude: +/-1.5 percent rdg. +/-0.03 Percent f.s. Full scale (f.s.) is the rated input current value. Frequency characteristics 40 Hz to 1 kHz (+/-8 percent or less). Maximum allowable input continuous 130 A rms (45 to 66 Hz). Maximum circuit voltage 300 V AC rms (insulated wire). Core jaw diameter: 37/64". Measures 1-51/64" width by 5-19/64" height by 53/64" depth. Cord length: 9-53/64'.

Manufacturer: Amprobe Brand: Amprobe Model: ACDC-400 Color: Multicolored

The Amprobe ACDC-400 TRMS digital clamp meter is a true RMS (root mean square) sensing, auto- or manual-ranging multimeter for measuring current, voltage, and resistance in electrical testing applications. It has a clamp that measures alternating current (AC) and direct current (DC) to 400 amp. The meter comes with detachable test leads that measure AC voltage and DC voltage to 600 volts (V), and resistance to 40 megaohms. The clamp has two jaws that can close around a conductor up to 1.1" (27 mm) in diameter to measure current or frequency without touching or interrupting the circuit. The relative zero mode stores a reading in memory to use as a zero point for subsequent readings, allowing quick comparison of multiple readings. The maximum or minimum reading mode displays the highest or lowest reading in a session to track a sudden increase or decrease in readings. It has a liquid crystal display (LCD) that shows readings both in digits and on a bar graph. The LCD is backlit for visibility in low light. An audible continuity sensor confirms that the circuit conducts electricity. The hold function keeps the reading on the display, even after the meter is disconnected. The unit automatically turns off after 30 minutes of non-use to conserve battery life, and a low-battery indicator signals when the meter's batteries need to be replaced. A finger guard on the body of the meter helps protect fingers from shock. This true RMS (root mean square) sensing meter provides accurate readings when measuring linear loads, such as standard induction motors and incandescent lights, where the current or voltage has a sinusoidal waveform, or non-linear loads, such as electronic devices or motors, where the current or voltage has a sinusoidal non-sinusoidal waveform. Two ranging modes (auto or manual) offer a range of operator control when taking readings. When turned on, the meter will be in auto-ranging mode and automatically selects select the correct operating range for the property being measured. It can be switched to manua...

Manufacturer: ETCR Brand: ETCR

Technical Specifications: Measurement Range:0mA-60.0A AC/DC Resolution:1mA AC/DC Accuracy:±2%rdg±5dgt (23℃±5℃, below 75%rh) Test Mode:Clip-on CT, integral mode Clamp Size:Φ7mm Display Mode:4 digits LCD display LCD Dimension:35mm×21.5mm; display domain: 32mm×15mm Sampling Rate:2 times/s Frequency:AC: 45Hz-400Hz Polarity Indication:DC current auto identified and display"-" Test Position:Tested wire in the jaw center Range Shift:Automatically Line Voltage:AC600V RS232 Interface:Data stored in the memory of the meter via RS232 upload to PC Com-Configure:Baud rate:9600, data bit:8, stop bit:1 Data Memory:99units, FULL blinks when the memory is full Reading Hold:DH indicating the reading is hold Out of Range:OL indicating the current is out of range Auto Power-off:5 Minutes after power on, it will power off automatically to lower the power consumption Battery Voltage:Indicating the battery voltage is lower than 7.2V.Then the battery have to be changed Working Current:10mA Consumption:10mW Working Temperature and Humidity:-10℃-50℃,below 80%rh Limit Temperature Error:-10℃-0℃ and 40℃-50℃, within 2%rdg Storage Temperature and Humidity:-10℃-60℃,below 70%rh Insulating Strength:AC2kV/rms (between the alloy of the clamp and the housing) Applicable safety rules:IEC1010-1, IEC1010-2-032, Pollution level 2, CAT Ⅲ(600V)

Manufacturer: Hioki Brand: Hioki Model: 3282

The Hioki 3282 digital clamp-meter is a true RMS sensing, auto-ranging multimeter for measuring current, voltage, frequency, and resistance in electrical testing applications. It has a clamp that measures AC (alternating current) to 1,000A (amperes). The clamp has two jaws that can close around an electrical conductor up to 46mm (1.81 inches) in diameter to measure current without touching or interrupting the circuit. A set of test leads is included for measuring AC voltage to 600V, frequency to 1,000Hz (hertz), and resistance to 10kΩ (kilohms). The meter has a rotary switch to select the property to measure, and a 3,000-count LCD that shows the reading numerically and in a 35-segment bar graph. The crest factor function uses a 1.00 to 5.00 scale to measure the quality of an AC signal and its ability to generate a particular voltage or current. The record function displays the maximum, minimum, and average readings for a property after the function is engaged. To aid documentation of readings and capture readings in tight spaces, the data hold function keeps the most recent reading on the display after disconnecting from the circuit. A continuity buzzer confirms that the circuit conducts electricity. The unit operates on a single 9V 6F22 battery, and turns off automatically after 10 minutes of non-use to conserve battery life. It has a low-battery indicator that signals when the battery needs to be replaced.This true RMS (root mean square) sensing meter provides accurate readings when measuring linear or non-linear loads, regardless of the waveform. It is auto-ranging, so it automatically selects the appropriate operating range for the property being measured. Accuracy and resolution specifications vary according to the range being measured. The meter meets EN (European Standard) safety standard 61010, and is rated for CAT (category) IV installations up to 600V, which covers equipment at the origin of the installation, such as electricity meters and primary over-current protection equipment. It has CE (Europea...