Current Testers - Page 86

Manufacturer: Measurement Specialties Brand: Measurement Specialties

Test Accessories - Other 4611 PROBE

Manufacturer: Fluke Corporation Brand: Fluke Model: EI-1625

The Fluke clip-on current transformer clamp set is used to perform selective or stakeless testing with the Fluke 1625 earth ground tester. Selective testing uses one clamp and stakes to measure earth ground loop resistance values for one ground electrode. Stakeless testing uses two clamps to test ground loop resistance. Both the selective and stakeless methods eliminate the need to disconnect the electrode from the grounding system for increased safety and fewer testing steps. One clamp is voltage inducing, and the other clamp is current sensing. Both clamps have a 50.8mm/2" inside diameter. Fluke Corporation manufactures electrical testing tools and software for industrial and commercial applications. The company, founded in 1948, is headquartered in Everett, WA.

Manufacturer: FLUKE CORPORATION Brand: Fluke Corporation

I1010/ Ac/Dc Current Clamp 1000A Dc 600A-2Pack.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-700RG31

The 700G Series Pressure Gauges (the Product) are high-accuracy digital pressure test gauges.

Manufacturer: Fluke Brand: Fluke Model: 773

EXCLUSIVELY FROM TRANSCAT - The Fluke 773 milliamp process digital clamp-meter is a manual-ranging meter for measuring DC milliampere (mA) and DC voltage output signals of 24V loop circuits. It has a clamp that measures DC to 100mA. The clamp has two jaws that can close around an electrical conductor up to 4.5mm (0.177 inches) in diameter to measure current without touching or interrupting the circuit, and has a 1m extension cable so it can detach from the meter body for hard-to-reach applications. A set of test leads is included for measuring DC to 24mA and DC voltage to 30V. The meter can source and simulate DC signals up to 20mA, can source DC voltage signals up to 10V, and is accurate to 0.2% with a resolution of 0.01mA. It has an LCD that shows both milliamp readings and percent of 4 to 20mA span, and a backlight for visibility in low light that turns off automatically after two minutes. An LED at the top of the meter body can be illuminated to aid visibility of wires in dark enclosures. The meter features a built-in 24V loop power supply for powering a transmitter and measuring its milliampere output signal, and a scaled milliampere output for connecting to a logging device (sold separately) to record measurements. To aid documentation of readings and capture readings in tight spaces, the data hold function keeps the most recent reading on the display after disconnecting from the circuit. The unit operates on four 1.5V AA batteries, and turns off automatically after 15 minutes of non-use to conserve battery life. It has a low-battery indicator that signals when the battery needs to be replaced.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-725 US

The multifunction process calibrator is a powerful yet easy-to-use field calibrator. Use the measure and source functions to test and calibrate almost any process parameter. Source/simulate volts, mA, thermocouples , RTDs, frequency, ohms, and pressure to calibrate transmitters. Support flow meter testing with frequency and CPM functions. Perform fast linearity tests with auto- step and auto-ramp features. Power transmitters during test using loop supply with simultaneous mA measurement. Handling of fast pulsed RTD transmitters and PLCs, with pulses as short as 10 ms. Store frequently used test setups for later use. Backlight lets you work in poor light. Large battery capacity of four AA cells. Battery door for easy changes. Voltage range: 0 to 100 mV, 0 to 10V (source), 0 to 30V (measure); voltage resolution - 0.01 mV, 0.01V, 0.01V; voltage accuracy - 0.02 percent Rdg + 2 LSD. Notes Max load, 1 mA. mA: 0 to 24 range, 0.001 mA resolution, .02 percent Rdg + 2 LSD accuracy. Notes max load, 1000 ohm. mV (TC terminals): -10.00 mV to 75.00 mV range, .01 mV resolution, .025 percent of range + 1 LSD accuracy. Resistance: 15 to 3200 ohm range, 0.01 to 0.1 ohm resolution, 0.10 to 1.0 ohm. Frequency range: 2.0 to 1000.0 CPM, 1 to 1000 Hz, 1.0 to 10.0 kHz; Frequency resolution - 0.1 CPM, 1 Hz, 0.1 kHz; Frequency accuracy - +/-.05 percent, +/-.05 percent, +/-.25 percent. For frequency source, waveform is 5V p-p squarewave, -0.1V offset. Loop Supply: 24V dc range, 10 percent accuracy. 30V maximum voltage. -40 to 71 degree C storage temperature. -10 to 55 degree C operating temperature. Relative humidity: 95 percent (10 to 35 degree C), 75 percent (30 to 40 degree C), 45 percent (40 to 50 degree C), 35 percent (50 to 55 degree C). Shock: 30g, 11ms, half-sine shock (or 1meter drop test). Vibration: random, 2g, 5-500 Hz. safety: CSA C22.2 No. 1010.1:1992. Battery: Four AA alkaline batteries. Battery life: 25 hours typical. Three years warranty.

Manufacturer: Hittime Brand: Hittime Model: 007360 Color: 4.5-30V Blue

Features: Brand new and high quality. Measuring Range: DC4.0-30V. Minimum input: DC4.5(Below this voltage,it will show measurement inaccurate, or don't show). Maximum Input: DC30V(please do not exceed 30V, otherwise, the meter would be damaged.). Display: three 0.56″LED digital tube. Display colors: blue. Refresh speed: about 500ms/each time. Allowable error: 1% (+ /-1). Power supply:No need power supply. Current consumption: Less than 20 mA, general 5-15 mA. Working temperature: -10℃ ~ 65 ℃. Size:4.8cm x 3cm x 2.2cm - 1.89inch x 1.18inch x 0.87inch. Package Included: 1 x DC 4.5-30V LED Voltmeter NO Retail Box. Packed Safely in Bubble Bag.

Manufacturer: Royal Vintage Spare Brand: Royal Vintage Spare

Amp meter. It has + and - sign on it. It has back light bulb in it and have printed royal enfield logo on it. It can be fitted to all models of royal enfield except thunderbird, machismo and 5 speed models.

Manufacturer: Extech Brand: Extech Model: TL807C

Extech TL807C ALLIGATOR CLIPS, 2 PACK FOR MULTIX SERIES

Manufacturer: Amico Brand: Amico

Descriptions:1.Measures current range of DC 0-250mA with accuracy of Class 2.5.2.Clear and easy to read scale and a button for fine tuning the dial.Specifications:Product Name: Analog Ammeter;Model: YS-50Measuring Current Range: DC 0-250mAAccuracy: Class 2.5Meter Face Size(Approx): 5 x 5 x 1cm / 1.9 inch x 1.9 inch x 0.39 inch (L * W * T)Thread Size: 0.3 x 0.9mm / 0.11 inch x 0.35 inch(D * L), 0.2 x 0.9cm / 0.07 inch x 0.35 inch(D * L).Overall Depth: 3.3cm / 1.3 inchColor: White, BlackNet Weight: 58gPackage Content:1 x Analog AmmeterSeveral Installing Parts.