Oscilloscopes & Accessories - Page 17

Manufacturer: Jinhan Electronic Brand: Jinhan

JDS2022A Input coupling AC、DC Channel 2 Display mode X-Y;Y-T The input impedance 1MΩ 25pF The maximum input voltage 40V（Probe X1）;400V（Probe X1）;2000V（Probe X100) Probe attenuation 1X,10X Attenuation setting 1X,10X,100X Signal acquisition system Sampling method Real time sampling, random sampling The storage depth 4K(2K per channel) Acquisition mode Sampling, peak detect Vertical system Vertical sensitivity 10mV-5V（Probe 1X）100mV-50V（Probe 10X）（1,2.5,5 Stepping） The vertical accuracy +/-3% The vertical resolution 8bit Bandwidth 20MHz Horizontal system The real-time sampling rate 200 MSa/s per channel Horizontal scanning range 10nS/div-5S/div Triggering system Mode Automatic, normal and single Type The rising edge, falling edge Automatic detection Support（50Hz-40MHz） Mathematical operation CH1+CH2,CH1-CH2,CH2-CH1 Measurement system Cursor measurement Support time and voltage Measuring method Manual Measurement The peak to peak value and frequency Equipment Screen 3.2 inch, 16 bit true color, TFT, 320*240 Battery 2000+mA Lithium battery (support 5 hours of continuous work) size 202*100*35（mm）

Manufacturer: Cal Test Electronics Brand: Cal Test Electronics Model: CT4024

The Elditest CT4024 is an 8 kV high voltage divider probe for use with both digital and analog oscilloscopes.

Manufacturer: Virtins Technology Brand: Virtins Technology

1. Package Contents: (1)VT DSO-2810R unit with a hardware activated Multi-Instrument Standard software license. (2)2 × 60MHz Oscilloscope Probe P6060 with two switchable positions: × 1, × 10. (3)1.5m USB cable. (4)CD (contains the copy-protected Multi-Instrument software). 2. Applications: (1) Ordinary oscilloscope, spectrum analyzer and signal generator functions, all of which work simultaneously. (2) DUT (Device Under Test) analysis such as frequency response. (3) High resolution and low noises at lower sampling rates, 10 voltage ranges from full scale +/-50mV to +/-50V, and support of sensor calibration make it suitable to work as a data acquisition device. (4) Signal Recording and Replaying.....Note: The signal generator function is through the computer sound card.

Manufacturer: Fluke Corporation Brand: Fluke Model: HART DRYWELL CABLE

Fluke HART DRYWELL CABLE Cable Kit, Hart Drywell Control

Manufacturer: Keysight Technologies Brand: KEYSIGHT TECHNOLOGIES Model: N2822A

For use with Keysight's N2820A and N2821A high-sensitivity current probes, the N2822A 20 m? tip provides 250 ?A to 5A of measurable range.

Manufacturer: Rigol Brand: Rigol Model: RP1300H

Rigol RP1300H Oscilloscope DC-300MHz Passive High Voltage Probe Accessory Features RP1300H is provided with several accessories designed to make probing and measurement simpler. Please take a moment to familiarize yourself with these accessories and their users.   RP1300H is provided with some accessories designed to make probing and measurement simpler. For digital oscilloscopes, the signal under test needs to be connected to the measurement channel via various oscilloscope probes or 50 ohm cables.The Probing is very important to making quality measurements. If the probe performance is not adequate or if you did not select the proper probe for your application, you will see distorted or misleading signals on your oscilloscope. There are two kinds of probes, one is passive probe, another one is active probe. active probe requires power while passive probe does not. For general-purpose measurements(600 MHz), active probes are the way to go. They cost more than passive probe and their input voltage is limited, but because of their significantly lower capacitive loading, they give you more accurate insight into fast signals.

Manufacturer: UNI-T Brand: UNI-T

1?Dual analog channels width range 1mV/div~20V/div; 2?7 inches widescreen LCD displays; 3?Special Print Scree Feature; 4?Supports plug-and-play USB storage device. Communication with and remote control of computer through the USB device; 5?USB drive system software upgrade; 6?Storage of waveforms setups and interfaces waveforms and setups reproduction; 7?Automatic measurement of 28 waveform parameters; 8?Unique waveform recording and replay function; 9?Multilingual menu displays.

Manufacturer: Cal Test Electronics Brand: Cal Test Electronics Model: CT2982B

The Elditest CT2982B is an 10 kV high voltage divider probe for use with both digital and analog oscilloscopes.

Manufacturer: Pico Brand: Pico Model: TA167-PICO TECHNOLOGY

Pico TA167 BNC 2000A/200A Current Clamp. 200 A / 2000 A AC/DC current probe, BNC connector The TA167 is a dual-range current probe capable of measuring AC and DC current signals up to 2000 A. Instructions Switch On When the probe is switched on to the required measuring range, the green LED will illuminate. The LED starts flashing when the battery voltage is too low for normal operation and warns the user that it requires changing. This procedure is described below. Auto Power OFF In order to save battery life, the probe will automatically switch itself off after approximately 10 minutes. To disable the Auto power off function, Switch Off the probe and Switch On whilst pressing the auto zero button. The red LED will illuminate and the probe will stay ON until switched off again. Auto Zero The output zero offset voltage of the probe may change due to thermal shifts and other environmental conditions. Select the required measuring range and to null the output voltage depress the Auto Zero button. Ensure that the probe is away from the current carrying conductor whilst the probe is being nulled. Current Measurement 1. Switch on the probe by selecting the required measuring range and check that the green LED is lit. 2. Connect the output lead to the oscilloscope, 3. Zero the probe using the Auto Zero button. 4. Clamp the jaws of the probe round the conductor ensuring a good contact between the closing faces of the jaws. 5. Observe and take measurements as required. Positive output indicates that the current flow is in the direction shown by the arrow on the probe. Battery Replacement The green or red LED will flash when the minimum operating voltage is approached. Use the following procedure: SAFETY WARNING Before removing the battery cover, ensure that the probe is disconnected from the oscilloscope and remote from any live electrical circuit

Manufacturer: LeCroy Corporation Brand: LeCroy Model: PP006A

Recommended for LT Series and WaveJet(A) Series (> 350 MHz) Oscilloscopes. Passive probe are the standard probe provided with most oscilloscopes. Typical passive probe provide a 10:1 attenuation and feature a high input resistance of 10 megohms. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probe are designed to handle voltages of at least 400V, some as high as 600V. LeCroy passive probe feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input. Bandwidth (probe only): 500 MHz. Input resistance: 10 megohms. Input capacitance: 12 pF. Maximum input voltage: 600 V. Attenuation: 10:01. Coupling: AC 1 megohms, DC 1 megohms, GND. Operating temperature: 0 to 50 degree C (32 to 122 degree F). Humidity: 80 percent (non-condensing). Probe diameter: 5mm. Interface: BNC. Attenuation sense pin. Recommended oscilloscope: LT series and WaveJet 300(A) less than or equals to 350 MHz.