Voltage Testers - Page 4

Manufacturer: KKmoon Brand: KKmoon

This DSO138 digital oscilloscope kit adopts ARM Cortex-M3 processor and with 2.4-inch TFT screen. It's easy and reliable for circuit operation. It can display frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values. This boost converter is an ideal match for DSO138 oscilloscope kit. It can be connected directly to the DSO138 motherboard(not included), make DSO138 oscilloscope to be a portable oscilloscope for better use.Case: DIY cover for DSO138 oscilloscope. Acrylic material, looks transparent(need to tear down the film). Easy for electronic enthusiasts to assemble.Specifications:DSO138 Kit Type: NOT Soldered DIY Kit / SMD Soldered Kit (Optional) Maximum Real-time Sampling Rate: 1Msps Accuracy: 12Bit Sampling Buffer Depth: 1024 bytes Analog Bandwidth: 0-200KHz Vertical Sensitivity: 10mV / Div - 5V / Div (1-2-5 progressive manner) Input Impedance: 1MΩ Maximum Input Voltage: 50Vpp (1: 1 probe), 400Vpp (10: 1 probe) Coupling Modes: DC / AC / GND The Horizontal Time Base Range: 10μs / Div - 50s / Div (1-2-5 progressive manner) Supply Voltage: DC 9V PCB Size: 117 * 76mm / 4.6 * 3in Screen Size: 52 * 40mm / 2 * 1.57in Package Size: 18 * 12.5 * 3cm / 7.08 * 4.92 * 1.18in Package Weight: 119g / 4.21ozNote: One oscilloscope DIY kit is all items are not soldered yet, the other kit has been soldered the SMD. Please choose what you like!Case: Material: Acrylic Item Weight: 156g / 5.52oz Package Size: 16 * 10 * 4cm / 6.3 * 3.94 * 1.57in Package Weight: 192g / 6.79ozWhat is included: 1 * DIY Cover for DSO138 1 * DSO138 DIY Digital Oscilloscope Kit 1 * Probe 3 * User Manual(English)

Manufacturer: TekPower Brand: Tekpower Model: TP2101 Color: Red

The TekPower TP2101 clamp meter can be used to measures AC/DC voltage, current, Resistance, Capacitance, and Temperature. Also, it can perform Diode and continuity test. It is a professional Meter that fit all electrical and electronic purpose. Specifications: Max. LCD display: 3999 Range selection: manual DC voltage: 0,4/4/40/400 V ± 0.8%, 1000 V ± 1.0% AC voltage: 4/40/400 V ± 1.0%,700 V ± 1.2% DC current: 400/1000 A ± 3.0% AC current: 400/1000 A ± 3.0% Resistance: 400/4k/40k/400k/4 MΩ ± 1,0%,40 MΩ ± 2.0% Capacitance: 4n/40n/400n/4 µF ± 4.0% Frequency range: 40 Hz --100 kHz ± 2.0% Temperature: -40 °C -- 750 °C ± 1.0% Duty cycle:0.1% -- 99.9% Diode test: yes Continuity test: yes Data hold: yes Dimensions 10 x 4 x 1 ¾ inches Power: 9V battery Weight: 1.06 lbs What's in the box: TP2101 clamp meter 9V battery Test leads Thermo probe User manual Carrying case

Manufacturer: UEi Brand: UEi Test Instruments Model: UTL260 Color: Black

The UTL260 from UEi Test Instruments has all the features and measurement functions that appliance technicians need in an every-day clamp-on meter.

Manufacturer: Honeywell Brand: Micro Model: CSLA2CD-W/SCREWS Color: black

This sensor is easily used with the Arduino platform such as the Arduino UNO which only costs you $20 through Amazon (Sold separately). The Arduino UNO has 6 Analog channels to monitor a 0 to 5V range. The Arduino UNO can be setup as an AC or DC datalogger / O-Scope for monitoring both current and Voltage (Voltage monitoring requires the use of a Voltage divider to scale the Voltage down to the input range of data logger) . If you would like the free LabVIEW software to use the Arduino for a datalogger or data acquisition O-Scope let us know and we will give you a link to download it. The hole diameter on this sensor is about 0.43 inches so it would fit up to a size 4 or size 2 AWG wire. The biggest advantage of this type of sensor is that you can loop a wire through the sensor as many times as you want to strengthen the signal. For example, if you loop the wire through 10 times with a supply of 8 Volts DC, then the sensitivity of this hall effect transducer will be about 330mV instead of 33mV (10 times larger sensitivity). ASSEMBLY REQUIRED HERE. You will need to connect the positive pin of this sensor to a DC voltage regulator such as the 7508 8V regulator. To build this simple circuit you will need to use a soldering iron and a voltage regulator. See picture in the listing for a schematic showing detailed information on how to hook this sensor up. This current sensor is a linear output Hall effect transducer. For every Amp that it detects, it changes its output by a few millivolts. If you want to see the exact sensitivity then take a look at the sensitivity chart above. It ranges from 24mv at 5 Volts supply, to 58mV per Amp with a 12 Volt DC supply. This sensor comes with mounting screws which are 0.375 inch long 4-40 screw and square nut (included) . However you could solder three wires to the pins and put heat shrink around each of them and runs this sensor to wherever you want.

Manufacturer: Fluke Corporation Brand: Fluke Model: PM9082/001

One red (signal) and one black (ground) 4mm banana contact. Consists of two adapters. Maximum signal voltage: 600V rms. Maximum voltage to ground: 600V rms. CAT III per IEC 61010-031. UL Listed.

Manufacturer: Efergy Brand: Efergy Color: White

Add this transmitter to your engage system to view multiple circuits. Ideal for installations that want to view solar and generation data separately or any home that needs to see the consumption of a different area separately

Manufacturer: ZIBOO Brand: ZIBOO Model: ZIBOO UT210D

Size name:ZIBOO UT210D Specifications: AC Current (A): 20A/200A ±（2.5%+8) DC Current (A): 20A/200A ±（2%+3) AC Voltage (V): 2V/20V200V/600V ±（1%+3) DC Voltage (V): 200mV/2V/20V200V/600V ±（0.7%+3) Resistance (Ω): 200Ω/2KΩ/20KΩ/200KΩ/2MΩ/20MΩ ±（1%+2) Frequency（Hz): 10Hz/100Hz/1kHz/10kHZ/60kHz ±（0.1%+4) Capacitance (F): 2nF/20nF/200nF/2μF/20μF/200μF/2mF/20mF ±（4%+5) Temperature（℃）: -40℃～1000℃ ±(1%+3) Temperature（℉）: -40℉～1832℉ ±(1.5%+5) General Characteristic: Power: AAA 1.5V × 2 LCD Size: 39.3mm × 26.5 mm Product Color: Red and Grey Product Net Weight: 170g Product Size: 175mm × 60mm × 33.5mm What's in the box: 1 * ZB-UT210D Clamp Meter 1 * ZB-UTL20 Test Lead 1 * Point Contact Temperature Probe 1 * English User Manual

Manufacturer: Farm Supply, LLC Brand: Field Guardian Model: 660055 Color: black

This is a good digital meter used to test the voltage on an electric fence. connect the metal probe to the alligator clip and either touch the probe to the ground post on the charger or insert it into the ground.

Manufacturer: Extech Brand: Extech Model: MN26V

Extech MN26V MULTIMETER, MINI TEC WITH FREE VOLT DETECTOR

Manufacturer: Extech Brand: Extech Model: VT10 Color: Multicolor

Voltage, continuity and phase tester with flashlight EHVT10 LED AC/DC voltage indication:AC: 24, 48, 120, 208, 240,277, 480, 600DC: 6, 12, 24, 36, 48, 110, 220, 400 EHVT30 LCD AC/DC Voltage indication6, 12, 24, 50, 230, 400, 690 Polarity detection with LEDs for positive and negative DC Continuity Test with audible tone Low impedance testing Built-in flashlight for testing in tight areas Phase rotation test Voltage function operates without battery Rubberized double-molded IP64 housing EHVT30 includes large backlit LCD display Dimensions: 9.4 x 3 x 1.6" (240 x 78 x 40mm) Weight: 8.4oz (237g)