Pressure & Vacuum Gauges - Page 107

Manufacturer: Winters Brand: Winters Model: PFQ728

The Winters PFQ series pressure gauge with brass wetted parts has a glycerin-filled circular dial enclosed in a stainless steel 304 case, and a male connection, and measures pressure with a single or dual scale with an accuracy of + or - 1.5% or 2.5%. The OT58 brass wetted parts are for measuring non-corrosive liquid and gas pressure. The stainless steel 304 case is also corrosion resistant and is Ingress Protection certified IP65 for protection against solid objects, including dust or liquids. The circular dial comes in 1.5" (40 mm), 2" (50 mm), 2.5" (63 mm), or 4" (100 mm) diameters and is filled with glycerin for protection against vibration and pulsation. The dial is white aluminum with black and red markings. It has an aluminum, anodized black, pointer and the lens is polycarbonate for high impact resistance. The gauge measures pressure with a single psi scale or a dual scale of psi/kPa, psi/bar, Hg. vacuum/kPa, or Hg. vacuum/bar. The gauge is accurate to + or - 2.5% of full scale value for the 1.5" and 2" dials and accurate to + or - 1.5% of full scale value for the 2.5" and 4" dials. The male connection comes with a 1/8", 1/4", or 1/2" NPT (National Pipe Thread) rate with a restricted orifice and is located at the bottom or center back of the gauge. The movement is OT59 brass, and the welding is silver alloy. The 6" (150 mm) socket gasket, the fill plug, and the lens ring gasket are all made of nitrile rubber for a tight seal. The over-pressure limit is 25% for pressures up to 1,400psi (9,653kPa) and 15% for pressures over 1,400psi (9,653kPa). The working pressure is a maximum of 75% of full scale value. The operating temperature is -4 to 150 degrees F (-20 to 65 degrees C). This pressure gauge is suitable for pumps, compressors, hydraulic presses, machinery, pneumatic equipment, and motors in harsh environments.Pressure gauges are instruments used to measure the pressure of a gas or liquid inside a vessel and, often, to help ensure the optimal amount of pressure for a given application. Pressure gauges ca...

Manufacturer: Winters Brand: Winters Model: PFQ747

The Winters PFQ series pressure gauge with brass wetted parts has a glycerin-filled circular dial enclosed in a stainless steel 304 case, and a male connection, and measures pressure with a single or dual scale with an accuracy of + or - 1.5% or 2.5%. The OT58 brass wetted parts are for measuring non-corrosive liquid and gas pressure. The stainless steel 304 case is also corrosion resistant and is Ingress Protection certified IP65 for protection against solid objects, including dust or liquids. The circular dial comes in 1.5" (40 mm), 2" (50 mm), 2.5" (63 mm), or 4" (100 mm) diameters and is filled with glycerin for protection against vibration and pulsation. The dial is white aluminum with black and red markings. It has an aluminum, anodized black, pointer and the lens is polycarbonate for high impact resistance. The gauge measures pressure with a single psi scale or a dual scale of psi/kPa, psi/bar, Hg. vacuum/kPa, or Hg. vacuum/bar. The gauge is accurate to + or - 2.5% of full scale value for the 1.5" and 2" dials and accurate to + or - 1.5% of full scale value for the 2.5" and 4" dials. The male connection comes with a 1/8", 1/4", or 1/2" NPT (National Pipe Thread) rate with a restricted orifice and is located at the bottom or center back of the gauge. The movement is OT59 brass, and the welding is silver alloy. The 6" (150 mm) socket gasket, the fill plug, and the lens ring gasket are all made of nitrile rubber for a tight seal. The over-pressure limit is 25% for pressures up to 1,400psi (9,653kPa) and 15% for pressures over 1,400psi (9,653kPa). The working pressure is a maximum of 75% of full scale value. The operating temperature is -4 to 150 degrees F (-20 to 65 degrees C). This pressure gauge is suitable for pumps, compressors, hydraulic presses, machinery, pneumatic equipment, and motors in harsh environments.Pressure gauges are instruments used to measure the pressure of a gas or liquid inside a vessel and, often, to help ensure the optimal amount of pressure for a given application. Pressure gauges ca...

Manufacturer: Dwyer Instruments Brand: Dwyer Model: 2001D Color: Black

Select the Magnehelic gage for high accuracy--guaranteed within 2% of full scale--and for the wide choice of 81 models available to suit your needs precisely. Using Dwyer's simple, frictionless Magnehelic gage movement, it quickly indicates low air or non-corrosive gas pressures--either positive, negative (vacuum) or differential. The design resists shock, vibration and over-pressures. No manometer fluid to evaporate, freeze or cause toxic or leveling problems. It's inexpensive, too.

Manufacturer: TechnologyLK Brand: TechnologyLK

Push-Pull capability. Range is from 0-35 Pounds Door Pressure Gauge Push-Pull instrument design specifically to measure force. This instrument is capable of measuring the entire range of forces found in servicing interior and exterior doors. OPERATING INSTRUCTIONS Set the top (small) o-ring located on the plunger rod on zero, down against the instrument's flange; or set the o-ring on the desired force. Holding the instrument firmly, press slowly against the door at a point approximately handle-high, and 30 inches away from the door's hinges. Read the amount of force required to open the door on the plunger scale closest to the bottom of the small o-ring. MEET ADA REQUIREMENTS The Americans with Disabilities Act requires that both interior and exterior doors of a building be handicapped accessible. Door Opening Force (4.1311 ADA AG). Exterior hinged doors:(Reserved) Interior hinged doors:5 lbs (22.2N) Sliding or folding doors:5 lbs (22.2N) Automatic/Power Assisted Doors:(4.13.12) Such doors shall not open to back check faster than 3 seconds and shall require no more than 15 lbs (66.6N) to stop door movement. If a power assisted door is used, its door-opening force shall comply with 4.13.11 and its closing shall conform to the requirements in ANSI A156.19-1984. Plastic Protective Tube for Door Pressure Gauge. Size:8" long 7/8" diameter Includes: One Door Pressure Gauge Push-Pull, 0-35 Lbs One Plastic Protective Tube

Manufacturer: Fluke Corporation Brand: Fluke Model: RPM80

Inductive Pickup for both conventional and distributor-less (DIS) ignitions.

Manufacturer: WIKA Instrument Corporation Brand: WIKA Model: 50533657

The WIKA industrial pressure gauge has stainless steel wetted parts, which resist corrosion against chloride samples, and has a circular dial that is enclosed in a stainless steel case that resists corrosion. The gauge measures pressure from 15 pounds per square inch (psi) to 15,000 psi, and is accurate to a variety of percentages across the entire range of the gauge, depending on other standard features, such as dial size. Accuracy ranges are: + or - 2.5 percent of span; + or - 1 percent of span over the entire range of the gauge, or American Society for Mechanical Engineering (ASME) B40.100 Grade 1A accuracy class; or + or - 2/1/2 percent of span over the entire range of the gauge, or ASME Grade A accuracy class. The male connection is available as a lower mount, a lower back mount, or a center mount, and comes with a choice of a 1/8", 1/4", or a 1/2" National Pipe Thread (NPT) rate. This pressure gauge is suitable for use in corrosive environments.Pressure gauges are instruments used to measure the pressure of a gas or liquid inside a vessel and, often, to help ensure the optimal amount of pressure for a given application. Pressure gauges can range from everyday instruments, such as those used to measure the air pressure in a car or bicycle tire, to highly accurate gauges used in mechanical and industrial processing. Most often, pressure gauges measure pressure relative to another reference. For instance, gauge pressure measures pressure relative to ambient air. An example of a pressure gauge measuring relative to ambient air is a tire pressure gauge or a blood pressure gauge. Differential pressure is the difference in pressure between two points, such as when measuring liquid flow along various points in a pipeline. An absolute pressure gauge measures pressure relative to a perfect vacuum, such as an atmospheric or barometric pressure gauge. All types of pressure gauges include either a male or a female mount to connect to the vessel where pressure is being measured, and display results on a dial with varying...

Manufacturer: CDN Brand: CDN Model: TCT572-G Color: Green

CDN (TCT572) Digital ProAccurate folding digital thermocouple thermometer is a great tool for any home. Get professional results every time! Perfect for thin cuts of meat, fish or poultry. The thermometer is accurate to plus or minus 2 F, and has a temperature range of -58 F to 572 F (-50 C to 300 C), with a response time of 3 to 6 seconds for quick, accurate readings. This thermometer is water resistant and shatterproof, and features an extra large backlit LCD display. The 304 stainless steel folding probe is 4 1/4 long with a 1. 5 mm tip. The housing is made from food-safe ABS plastic with BioCote. This thermometer can be field calibrated, and features both a maximum and a minimum feature, which display the highest or lowest temperature among multiple readings. The thermometer has an on/off button, as well as an auto-off feature. This thermometer is NSF listed. Requires 3V Button IEC CR2032 Lithium batteries, which are included. Colors vary.

Manufacturer: CME Brand: CME Tools

* Precision Master Bar Level. * 6"Lx 1-1/2"W x1-5/16"H * Tollerance 0.0002"/10" Longitudinal with prismatic base. * QUESTIONS? Tel: 1-800-254-0007 Cel#:248-207-9813

Manufacturer: Dwyer Instruments Brand: Dwyer Model: DPGA-10

The Series DPGA is the only economic digital pressure gage with selectable engineering units on the market. With its 1% accuracy and digital push-button zero, the DPGA is the perfect choice for digitally monitoring the pressures of air and compatible gases.

Manufacturer: CME Tools Brand: CME Tools