Pressure & Vacuum Gauges - Page 15

Manufacturer: Fluke Corporation Brand: Fluke Model: BP7235

Fluke NIMH rechargeable battery pack. Provides typical 16-hour battery life when used in 700 or 740 calibrator. 6 1.2V DC Ni-MH cells in custom-molded ABS/PC-blend case. Measures 7.1-inches length by 2.2-inches width by 0.9-inches height. 1 year warranty.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-FP PLUS Color: White

The Fluke FoodPro Plus dual infrared and RTD thermometer takes noncontact or contact temperature measurement and is used to monitor the temperatures of food products and foodservice equipment. This thermometer measures surface temperature from -35 to +275 degrees C (-31 to +527 degrees F) with an infrared sensor and measures internal temperatures from -40 to +200 degrees C (-40 to +392 degrees F) with a built-in fold-out resistance temperature detector (RTD) probe sensor. It has a 2.5:1 infrared distance-to-spot ratio with LED illumination for highlighting the measurement area. Go/No-Go lights indicate when food is in an unsafe temperature range (40 to 140 degrees F) to meet Hazard Analysis of Critical Control Points (HACCP) guidelines. This thermometer is used by foodservice professionals to measure food product and equipment temperatures and help detect potential food safety problems.The Fluke FoodPro Plus shows the maximum temperature for reference. The backlit display helps eliminate light reflections and improves contrast in low-light conditions. It has an integrated countdown timer and alarm to help monitor cooking and cooling intervals and food service line inspections. It is Ingress Protection certified IP54 for dust and splashing liquid and can be hand washed without submersion after use. The European Conformity (CE) marking indicates compliance with applicable European Union (EU) directives. It comes with one 9V battery, a soft case, a calibration certificate with National Institute of Standards and Technology (NIST) traceability and the German Calibration Service (Deutscher Kalibrierdienst, DKD) traceability, and instructions. SpecificationsInfrared temperature range-35 to +275 degrees C (-31 to +527 degrees F)Infrared sensor accuracy0 to 65 degrees C (32 to 150 degrees F): + or - 1 degree C (+ or - 2 degrees F); above 65 degrees C (150 degrees F): + or - 1.5% of the reading; below 0 degrees C (32 degrees F): + or - 1 degree C (+ or - 2 degrees F) + or - 0.1 degreeDistance-to-spot ratio2.5:1Infrared se...

Manufacturer: Fluke Corporation Brand: Fluke Model: 4144616

Fluke low energy universal battery charger.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-566

These infrared thermometers are extremely easy to use: just aim, pull the trigger, and read the display. The backlit display shows temperature readings in °F or °C; low-battery indication; and hold, scan, and max. Display holds for seven seconds. Under range and over-range conditions are also indicated on the display. Available for sale in the United States and Canada only. Fluke models 566 and 568 offer additional features including an innovative graphical display, adjustable emissivity through an easily selectable built-in material table , type K thermocouple input, datalogging, multiple language interface, two backlighting levels, and a rubberized housing that improve resistance to shock, damage, water, and dust. These meters also indicate min/max, dif, avg, two color flashing with audio high and low alarms, probe, log, and recall. The 568 has expanded datalogging capabilities, with internal memory for up to 99 datapoints, or unlimited datapoints through the USB interface direct to your PC. Easy trend analyze can be done through the use of FlukeView software. Ideal for maintenance diagnostics in demanding environments Laser targets your measurement area. For special surfaces such as concrete all Fluke models have adjustable emissivity (except Fluke 63)

Manufacturer: Yellow Jacket Brand: Yellow Jacket 69051 eVac Pro Vacuum Gauge Model: 69051

Range: 0 - 25,000 Microns (3333.1 Pa, 33.331 mBar, 25,000 mTorr, 25.000 mmHg) Vacuum Accuracy: 5% of Reading +/- 5 Microns Vacuum Resolution: 0.1 Micron (@ 0.0 to 9999.9 Microns) Temperature Accuracy: 0.2°F (0.1°C) Temperature Resolution: 0.1° Warm-up Time: Instant Response Time: Instant Power: 9V Alkaline Battery (included) (9V Lithium recommended for low temperature operation) Battery Life: Up to 300 Hours Operating Temperature: 10°F - 122°F (-12°C - 50°C) Weight: 6 oz. (170 g) including battery and swivel hook Dimensions: 3.5" x 3" x 1.25" (9 x 7.5 x 3 cm)

Manufacturer: Ashcroft Inc. Brand: Ashcroft Model: 451082AS02L200#

The standard Ashcroft test gauge case style features a solid-front aluminum case with a hinged ring. The dial has a polished mirror band for pointer reflection to prevent parallax error. Pointer is a balanced-friction adjustable design with red knife edge tip for easy reading.

Manufacturer: General Wire Brand: General Wire Model: KR-D-WC Color: NA

The Kinetic Water Ram uses a burst of compressed air that drives a shock wave (kinetic energy) through water to break up stoppage. It's particularly useful when the stoppage is on the far side of a drum trap or series of tight bends, since the shock wave can travel around bends without losing its force.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-1503

The Fluke high-voltage digital megohmmeter is an insulation tester with preset and adjustable test voltages for measuring insulation resistance to 1TΩ (2TΩ for 10kV models) to indicate the condition of windings or cables in motors, switchgears, electrical installations, and other insulated equipment, and it also measures leakage current to 2 milliamperes (mA), capacitance to 20μF, and AC and DC voltage to 600V, signaling when a voltage greater than 30V is detected. In addition to the preset test voltages of 250V, 500V, 1,000V, 2,500V, 5,000V, plus 10,000V for the 10kV models, test voltages can be adjusted in 50V increments to 1,000V and 100V increments above 1,000V. Its PI/DAR (polarization index/dielectric absorption rate) function automatically calculates PI and DAR, which are measurements over time that give a truer indication of insulation condition than single-point measurements. The meter can perform timed tests up to 99 minutes, adjustable in 1-minute increments, and has storage for up to 99 test results. Stored results can be uploaded to a PC with the included FlukeView Forms Basic software. The software is compatible with Microsoft Windows 2000, XP, and Vista. For improved accuracy during high-resistance testing, the guard terminal eliminates interference from leakage current. The meter has an LCD that shows the reading numerically and in a bar graph. Megohmmeters are commonly used for electrical maintenance and testing in industries such as HVAC, transportation, manufacturing, mining, and utilities, among others. The meter is rated for category (CAT) IV installations to 600V, which covers equipment at the origin of the installation, such as electricity meters and primary over-current protection equipment, and CAT III installations to 1,000V, which covers equipment in fixed installations, such as switches in the fixed installation and some industrial equipment that is permanently connected to the fixed installation. The unit has a low-battery indicator that signals when the battery needs to be r...

Manufacturer: Missyee Brand: Missyee

Detail about Diesel Fuel Injector checker: Power:W Item Height:20 cm Brand Name: Voltage:V Model Name:Diesel Fuel Injector checker Item Width:30 cm Car Maker:Audi,Australia Ford,Benz,BMW,Brilliance,Chevro Hardware Version: 2016 Software Version: Diesel Fuel Injector checker Language: English External Testing Certification: CE Item Length: 50 cm Item Type: Pressure & Vacuum Testers Material Type: Metal and plastic Item Weight:5 kg fuel injector nozzle tester : 0 - 400 BAR / 0 - 6000 PSI Dual Scale Gauge BO-SCH injector checker is suitable for: all common rail injector and mechanical injectors Special Features:Diesel Injector Nozzle Tester Color:Black Quality:High Quality Place of Origin:Mainland China Price:Factory Price Is_customized:yes Unit Type: piece Package Weight: 5.000kg (11.02lb.) Package Size: 50cm x 30cm x 20cm (19.69in x 11.81in x 7.87in)

Manufacturer: Mid-West Instrument Brand: Mid-West Instrument Model: 845

Mid-West Instrument Backflow prevention assembly test kit includes 5 valve. The 835 is in the list of acceptable gages from both FCCC and HR-USC and CA-NV AWWA. Backflow test kits provide the capability for testing all brands of reduced pressure principle, pressure vacuum breaker, spill resistant vacuum breaker and double check valve backflow prevention assemblies. Over 30 years of input from Backflow technicians. Specially designed for testing backflow prevention assemblies. Soft-seated brass needle valves (with replaceable valve seats). Test kit is protected with 90 micron filters to minimize plugging with scale, sand, etc. Filter elements can be cleaned or replaced. Improved case with storage compartments for fittings and tools. Test procedures are laminated in clear plastic. 5 Year warranty. Gauge type diaphragm differential pressure. Dial size and range (4-1/2-inches) 0-15 psid/0-100 KPA. Differential pressure accuracy +/-0.2 P.S.I.D. (Descending). Working pressure: 200 psig. Body material: glass reinforced engineering thermoplastic. Wetted internals: EP elastomers, brass and 316 stainless steel metal parts. Line pressure gauge: 1-1/2-inches 0-200 psig. Hoses and end fittings: Buna-N jacket and liner. Schrader 1/4-inches brass coupler. Hose length: three (3) each/5-feet long (color-coded). Bleed tube, one each/4-feet long clear bleed tube. Adaptor fittings: (3) sets of brass fittings provided for hookup to all standard size test cocks. Temperature limitations: maximum 150 degree F/65 degree C. Measures 18-1/2-inches length by 9-inches width by 9-3/4-inches height. Freezing temperatures must be avoided.