Current Testers - Page 99

Manufacturer: Pomona Electronics Brand: Pomona Electronics

Test Plugs & Test Jacks RED PANEL JACK BU-31609-2

Manufacturer: Fluke Corporation Brand: Fluke Model: EI-162AC

Fluke EI-162AC Clip-on Current Transformer (Inducing) The EI-162AC Clip-On Current Transformer (Inducing) is used along with the Fluke 1623 or 1625 to perform Selective and Stakeless testing. Selective testing means using one clamp along with earth ground stakes to provide earth ground loop resistance values for one earth ground electrode. Stakeless testing uses two clamps to perform earth ground loop resistance measurement without stakes. Both tests have the advantage of providing measurements with no disconnection from the grounding system! Safer and quicker.

Manufacturer: Kyoritsu Brand: Kyoritsu Model: 8124

Kyoritsu 8124 load current clamp sensor. In order to monitor energy saving and to control the electric facilities, it is essential and imperative to control the leak and load currents from mains and branch power lines up to the equipment. Clamp sensor is easy to carry and simple to install. Load current detection type clamp sensors provide superior characteristic in phase for the use of power meter. Rated current 1000Amp AC. 68mm conductor size. Output voltage: AC 500mV/1000A (AC 0.5mV/A). Accuracy: +/- 0.5 percent rdg +/- 0.1mV (50/60Hz), +/- 1.0 percent rdg +/- 0.2mV (40Hz to 1kHz). Phase shift within +/- 1.0 degree. Output connector: Mini-DIN 6-pin. 0 to 50 degree c temperature range. Withstand voltage: 5350V AC for 5 seconds. Approximate 3m cable length. Approximate 1 ohm output impedance. Accessories includes: portable case, instruction manual, cable marker. Measures 186 mm length by 129 mm width by 53mm depth.

Manufacturer: Harwin Brand: Harwin

Contact Probes 1.27mm SPRING PROBE 2 PART CONVEX HEAD

Manufacturer: IDI Brand: D.I.D.

Contact Probes HEADED .035 60 DEG CHISEL STEEL

Manufacturer: AEMC Brand: AEMC Model: SL261

The model SL261 is designed for AC/DC current measurement capabilities using hall effect technology. It measures from a few mA to over 100A. The "screw driver" shape, with its narrow elongated prod, was chosen to permit probing in crowded cable bundles, or measuring in tight areas such as on circuit boards, motor controllers and automotive circuitry. The electronics and batteries are self - contained in the handles. It is an excellent companion to DMMs, recorders and loggers, oscilloscopes and waveform displaying instruments. Low phase shift also insures reliable power and power quality measurements. The model SL261 is designed for current measuring and displaying on oscilloscopes. AC + DC output signals proportional to the total current are provided for true RMS measurements. Low AC and DC measurements. 50mA to 120AAC/150ADC. Unique design for probing in crowded wiring in industrial and automotive environments. Hall effect sensor technology. Use with DMMs, voltmeters and other voltage measuring instruments. Double insulation, CE mark. 10A and 100A Nominal range. 100mA to 100A Measurement range. Voltage output transformation ratio. 10A-100mV/A, 100A-10mV/A Output signal. Overload: red LED indicates input greater than the selected range. DC to 100kHz (-3dB with current derating) Frequency range. 600Vrms Working/Common mode voltage. 6.5' coaxial cable output termination. Operating temperature: 32 degree to 122 degree F. Storage temperature: -22 degree to 176 degree F. 0.46" Jaw opening. Dimensions: 9-11/128" width by 1-53/128" height by 2-81/128" depth. Weight 11.6oz with battery.

Manufacturer: IDI Brand: D.I.D.

Contact Probes .10 CTR 3 AMP PROBE HEADED 4 PT CRWN STL

Manufacturer: AEMC Brand: AEMC Model: 2124.91

AmpFlex 0.5A to 3000A, 200kHz for Oscilloscope OX series.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-700SW

DPC/track Software. This product has been replaced by DPC/Track2 which is the CMS software now recommended for use with Fluke 74x and Fluke 75x models. DPC/Track is still applicable for purchase because it provides French, German, Spanish and Italian versions. DPC/TRACK software includes an instrumentation data-base that makes it easy to manage your instrumentation, create and schedule tests, load and unload the 743, print a variety of standard reports, and manage calibration data. Print standard reports automatically. The software assembles pre-formatted reports from your database files, saving time and reducing errors. Reports include calibration certificates, instruments due for calibration, inventory characteristics, calibration histories, calibration procedures, and traceability to instruments touched. User-defined lists enable technicians to select reasons for work, problems found, and actions taken from lists you define. These lists work with your application software to automatically generate a complete record of calibration results and actions that can fulfill documentation requirements for ISO-9000 and other quality regulations.

Manufacturer: Fluke Corporation Brand: Fluke Model: 4637337

Fluke 12 inch iFlex flexible current probes measure to 1500A AC while providing the ultimate measurement flexibility. The iFlex probes connect directly to the energy logger, displaying current measurements without error prone scaling factors. The 1.8 m (6 ft.) cord allows separation between the measurement location and the energy logger making it easier to view the display.