Oscilloscope Accessories - Page 21

Manufacturer: Fluke Corporation Brand: Fluke Model: I5S

Expand the use of your Fluke 430 series power quality tool or ScopeMeter test tool with this 5A AC current clamp, specially configured to provide good accuracy at low levels e.g. while taking measurements on secondary current transformers. Compact shape makes transporting and storing convenient. Take accurate readings without breaking the circuit. CAT III 600 V (For insulated conductors only). Nominal current range: 5A. Continuous current range: 10mA to 6A. Maximum non-destructive current: 70A. Lowest measurable current: 10mA. Basic accuracy: 10mA to 1A: 1 percent + 5 mA, 1A to 5A: 1 percent. Useable frequency: 40 Hz to 5 kHz. Output levels: 400 mV/A. Input load impedance: greater than 1 mega ohm in parallel with up to 47 pF. Crest factor: less than or equal to 3, add 0.7 percent to accuracy. Safety: CAT III 600V per IEC/EN61010-1, Pollution Degree 2. Maximum voltage: 600V AC. Maximum conductor diameter: 15mm. Output cable length: 2.5m. With BNC adapter. Measures 116mm length by 43mm width by 23mm height.

Manufacturer: Fluke Corporation Brand: Fluke Model: EI-1625

The Fluke clip-on current transformer clamp set is used to perform selective or stakeless testing with the Fluke 1625 earth ground tester. Selective testing uses one clamp and stakes to measure earth ground loop resistance values for one ground electrode. Stakeless testing uses two clamps to test ground loop resistance. Both the selective and stakeless methods eliminate the need to disconnect the electrode from the grounding system for increased safety and fewer testing steps. One clamp is voltage inducing, and the other clamp is current sensing. Both clamps have a 50.8mm/2" inside diameter. Fluke Corporation manufactures electrical testing tools and software for industrial and commercial applications. The company, founded in 1948, is headquartered in Everett, WA.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-700RG31

The 700G Series Pressure Gauges (the Product) are high-accuracy digital pressure test gauges.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-725 US

The multifunction process calibrator is a powerful yet easy-to-use field calibrator. Use the measure and source functions to test and calibrate almost any process parameter. Source/simulate volts, mA, thermocouples , RTDs, frequency, ohms, and pressure to calibrate transmitters. Support flow meter testing with frequency and CPM functions. Perform fast linearity tests with auto- step and auto-ramp features. Power transmitters during test using loop supply with simultaneous mA measurement. Handling of fast pulsed RTD transmitters and PLCs, with pulses as short as 10 ms. Store frequently used test setups for later use. Backlight lets you work in poor light. Large battery capacity of four AA cells. Battery door for easy changes. Voltage range: 0 to 100 mV, 0 to 10V (source), 0 to 30V (measure); voltage resolution - 0.01 mV, 0.01V, 0.01V; voltage accuracy - 0.02 percent Rdg + 2 LSD. Notes Max load, 1 mA. mA: 0 to 24 range, 0.001 mA resolution, .02 percent Rdg + 2 LSD accuracy. Notes max load, 1000 ohm. mV (TC terminals): -10.00 mV to 75.00 mV range, .01 mV resolution, .025 percent of range + 1 LSD accuracy. Resistance: 15 to 3200 ohm range, 0.01 to 0.1 ohm resolution, 0.10 to 1.0 ohm. Frequency range: 2.0 to 1000.0 CPM, 1 to 1000 Hz, 1.0 to 10.0 kHz; Frequency resolution - 0.1 CPM, 1 Hz, 0.1 kHz; Frequency accuracy - +/-.05 percent, +/-.05 percent, +/-.25 percent. For frequency source, waveform is 5V p-p squarewave, -0.1V offset. Loop Supply: 24V dc range, 10 percent accuracy. 30V maximum voltage. -40 to 71 degree C storage temperature. -10 to 55 degree C operating temperature. Relative humidity: 95 percent (10 to 35 degree C), 75 percent (30 to 40 degree C), 45 percent (40 to 50 degree C), 35 percent (50 to 55 degree C). Shock: 30g, 11ms, half-sine shock (or 1meter drop test). Vibration: random, 2g, 5-500 Hz. safety: CSA C22.2 No. 1010.1:1992. Battery: Four AA alkaline batteries. Battery life: 25 hours typical. Three years warranty.

Manufacturer: withutrade Brand: Hantek HT25

The HT201 has been designed to allow fuel injector and primary ignition waveforms to be measured using Hantek oscilloscope products. Please note this attenuator should not be used for any high voltage measurements other than fuel injectors and primary ignition. Specification: Attenuation: 20:1 Bandwidth: 10MHz Input Res: 1.053M

Manufacturer: Hantek Brand: Hantek PP80

Oscilloscope Rapier Performance & Characteristics ● Attenuation ratio: 1× and 10× optional. ● Portable design according with ergonomics. ● Integral injection molding makes the usage more flexible and the oscilloscope able to adapt more testing situations. ● Safety standards: it has passed the CE Attestation of European Community. Application Fields ● Compatible with domestic and international digital and analog oscilloscopes in relevant frequency. ● Measurement in intermediate and low frequency signals. Order Information Accessories included by PP series passive voltage rapier ● Operation manual ● Adjusting tool: adjusts compensation capacitance to assure the rapier match with oscillograph. ● Contractive-type acuminate hook ● 12cm earth wire with alligator clip ● 4 pairs of colorized cable markers ● Locating sleeve adapts to IC testing. Double-nip wire

Manufacturer: Fluke Corporation Brand: Fluke Model: FLK-CNX C3002

The CNX C3002 Modular DMM 2-Compartment Soft Case is as versatile as the CNX wireless test tool team. This carrying case can work alone, holding the CNX Wireless Multimeter and test leads, or can be attached to the CNX C3000 Premium Modular Tool Bag. Your CNX tools are always within easy reach, ready for testing.

Manufacturer: Fluke Corporation Brand: Fluke Model: C520A

Large tool belt loop and top flap to secure meter. Holds Fluke Electrical Testers. 1 year warranty. Measures 3.125" width by 10" height by 2.125" depth.

Manufacturer: Fluke Corporation Brand: Fluke Model: BB120

Safety designed female BNC to shielded banana adapter for use with Fluke ScopeMeter 120 series and Fluke-43B power quality analyzer. Two adapters come in package. Maximum signal voltage: 300V rms CAT III per IEC 1010-02-031. Maximum voltage to ground: 600V rms CAT III per IEC 1010-2-031.

Manufacturer: Fluke Corporation Brand: Fluke Model: C800

Tough polypropylene case. Accessories and manual compartments. Detachable lid. 1 year warranty. Measures 15" height by 9" width by 4-1/2" depth.