Oscilloscopes & Accessories - Page 83

Manufacturer: TTi Brand: TTI

High resolution & accuracy The 1705 is a 4¼ digit meter with a scale length of 12,000 counts and a resolution of 10µV, 10mOhms and 0.1µA. Combined with a high basic dcV accuracy of 0.04%, it provides measurements that are an order of magnitude better than most hand-held DMMs. Dual display system The 1705 has both a main display and a secondary display. The two displays can be used for a variety of purposes: To show the selected range in addition to the measurement units (e.g. 100mA dc). To display a measurement in two different units - (e.g. ac volts and dBm). To display the result of a calculated function - (e.g. Ws value and % deviation). To measure and display two parameters of one signal - (e.g. ac and dc volts). To measure and display two different signals - (e.g. ac volts and dc current). Wide bandwidth ac with true RMS The 1705 provides True RMS ac response which gives accurate measurements regardless of the waveform shape. The wide bandwidth attenuator provides high accuracy within the audio band and gives extended response to avoid errors when measuring switching waveforms. Measurements are normally ac coupled but, when required, the true RMS value of the ac plus dc components can be shown. Frequency & capacitance The 1705 offers high accuracy frequency measurement (better than 0.01%) from 10Hz to 120kHz. It uses a reciprocal counting technique to give up to 0.01Hz resolution at 10 readings per second. The 1705 also incorporates capacitance measurement in four ranges up to 120µF. Wide range of Smart functions The 1705 offers computing and datalogging functions as standard: dBs, Ax+b, Limits, % deviation, Min-Max, Power, and a 100 reading Data-logger. Full bus control via RS-232 The 1705 has an RS-232 interface as standard which can be used for remote control and read-back of measurements. Dual measurement The 1705 can measure and display two signals simultaneously.  These can be two parameters of one signal (e.g

Manufacturer: AGILENT TECHNOLOGIES Brand: Agilent Technologies

AGILENT TECHNOLOGIES DSOXLAN LAN/VGA CONNECTION MODULE

Manufacturer: Fluke Corporation Brand: Fluke Model: BHT190

Set of break-out adapters for the three most common industrial bus connection systems M12, DB-9 and RJ-45. Each board works as a straight-through connection for the bus cable and gives access to the individual wires and pins of the connector system for hooking up probes. Break-out adapter DB-9, male-to-female. Gives access to pins 1 thru 9 and shield. Break-out adapter M12, with cables, male-to-female. Gives access to pins 1 thru 5. Break-out adapter RJ-45, female-to-female with patchcable (patchcable not shown on photo). Gives access to pins 1 thru 8 and shield. Maximum voltage: 30V rms, 42V peak, between any connection and between connections and ground.

Manufacturer: Hantek Brand: Hantek DSO1102B

Bandwidth:100MHz Channel:2 Real-Sample Rate:1GSa/s Equivalent Sample Rate:25GSa/s Record Length:1M Rish time:≤3.5ns Timebase Accuracy:±50ppm Time Base Range:Time Base Range Input Impandance :Input Impandance VOLTS/DIV Range:VOLTS/DIV Range A/D Converter:8bit Position Range:±50V(5V/div), ±40V(2V/div～500mV/div), ±2V(200mV/div～50mV/div), ±400mV(20mV/div～2mV/div) DC Gain Accuracy:±3% for Normal or Average acquisition mode, 5V/div to 10mV/div; ±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div. Bandwidth Limit:20MHz Trigger Types:Edge, Video, Pulse, Slope, Over time, Alternative Trigger Source:CH1, CH2 Math:+, -, x, ÷, FFT, Invert Cursor Measurement:Voltage difference between cursors: △V; Time difference between cursors: △T; Reciprocal of △T in Hertz (1/ΔT); Auto Measuerment:Frequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time, +Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF DMM Max. Resolution:6,000 Counts Testing Modes:Voltage, Current, Resistance, Capacitance, Diode & Continuity Max. Input Voltage:AC: 600V, DC: 800V Max. Input Current:AC:10A , DC: 10A Max. Input Impandance:10MΩ Display:5.6"TFT 16K Color Display, 640*480 dots Size:245mm x 163mm x 52mm Weight:1.3KG(Without Package) Standard Probe:PP150x2

Manufacturer: Cal Test Electronics Brand: Cal Test Electronics Model: CT3687

DSO active differential probe with 100x and 1000x attenuation ranges and voltage measurements up to +/-1400 V. Bandwidth to 100 MHz. Powered by 4 AA batteries or optional 6V DC mains adapter. Applications include: precise power semiconductor device measurements, switching power supply design, precise measurement of power converters, precise measurement of motor derived. Features: Up to +/-1400 V differential. 100 MHz bandwidth (-3 dB). High accuracy +/-2 percent. Safety certified. High CMRR. Accessories: spring loaded hook probes, 4 AA batteries, manual. Reference SI-9110. Bandwidth: 100 MHz. Attenuation(s): 100x/1000x. Accuracy: +/-2 percent. Rise time: 3.5 ns. Input impedance: 4 Mohm/7 pF. Input voltage: Differential voltage (DC+Peak AC): +/-140V / +/-1400 V. Common-mode voltage (DC+Peak AC): +/-1400V or 1000 Vrms. Absolute max. voltage (DC+Peak AC): +/-1400V or 1000 Vrms CAT III. Output voltage: Swing: +/-7V (into 50 kohm load). Offset (Type): +/-5 mV. Noise (Type): 0.9 mVrms. Source impedance (Type): 50 kohm. CMRR (Type): -80 dB at 60 Hz; -50 dB at 1 MHz. Operating temperature/humidity: -10 to +40 degree C / 25 to 85 percent RH. Storage temperature/humidity: -30 to +70 degree C / 25 to 85 percent RH. 95cm Cable length. 30cm Input leads length. 2002/95/EC RoHS compliant. Measures: 202mm length by 83mm width by 38mm height.

Manufacturer: Rigol Brand: Rigol Model: MC3324

Rigol MC3324 MIX Module 20-voltage-channel+4-current-channel Mixed Multiplexer . 24 channel multiplexer module for use with M300 DAQ System Mainframe and MC3065 DMM module. This card has 20 voltage channels configurable for 2 or 4 wire measurements and 4 current only measurement channels. The M3TB24 is the mating terminal block for this module. MC3324 (24-Channel Multiplexer)??Ü The MC3324 is a mixed multiplexer with 20 voltage channels and 4 current channels. All 20 voltage channels switch both HI and LO inputs, thus providing fully isolated inputs to the DMM module, and is divided into two banks (called A and B) of 10 two-wire channels each. When making 4-wire resistance measurement, the instrument automatically pairs channels of A bank and B bank. All channels are break-before-make. You can close multiple channels on this module only if you have not configured any channel to be part of the scan list. 4 current channels are used in combination with the DMM module to measure DC current or AC current. All channels are break-before-make. In any case, you cannot close multiple channels on this module. This module can be connected with MC3065 (DMM Module, if MC3065 is currently inserted). Measurement Connections Using External Terminal Blocks  M300 provides 6 kinds of terminal blocks to easily connect the signal to be measured to the module. The models of the terminal blocks and corresponding modules are listed in the table below. This section introduces how to use the external block.   Terminal Block Module 1 M3TB32 MC3132, MC3232 2 M3TB64 MC3164, MC3264 3 M3TB24 MC3324 4 M3TB48 MC3648 5 M3TB16 MC3416 6 M3TB34 MC3534 Note: for the MC3724, the signal can be connected to the SMB connectors on the module directly. No terminal block is needed

Manufacturer: Hantek Brand: Hantek DSO5062BMV

Features: •60MHz bandwidth •1GSa/s Real time sample rate •Trigger mode:edge/pulse width/line selectable video/slop/overtime etc •USB host and device connectivity, standard •Multiple automatic measurements •Provides software for PC real-time analysis •With video help function,built-in 2GB flash memory card Specifications: •Model:DSO5062BMV •Bandwidth:60MHz •Channel:2 •Real-Time Sample Rate:1GSa/s •Equivalent Sample Rate:25GSa/s •Memory Depth:2M •Rise Time:1.7ns/3.5ns/5.8ns •Time Base Accuracy:±50ppm •Time Base Range:2ns/div-40s/div •Video Help:Yes •SD Card:Yes •Input Impendance:1MΩ •VOLTS/DIV Range:2mV/div～5V/div •A/D Converter:8 bit •Position Range:±50V(5V/div),±40V(2V/div～500mV/div), ±2V(200mV/div～50mV/div),±400mV(20mV/div～2mV/div) •DC Gain Accuracy: ±3% for Normal or Average acquisition mode,5V/div to 10mV/div; ±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div •Bandwidth Limit:20MHz •Trigger Types:Edge,Video,Pulse, Slope,Over time,Alternative •Trigger Source:CH1,CH2,EXT,EXT/5, AC Line •Math:+,-,x,÷,FFT •Cursor Measurement: Voltage difference between cursors: △V; Time difference between cursors: △T; Reciprocal of △T in Hertz (1/ΔT) •Auto Measuerment:Frequency,Period, Mean,Pk-Pk,Cycli RMS,Minimum, Maximum,Rise time,Fall Time,+Pulse Width,-Pulse Width, Delay1-2Rise, Delay1-2Fall,+Duty,-Duty,Vbase,Vtop, Vmid,Vamp,Overshoot, Preshoot,Preiod Mean,Preiod RMS,FOVShoot, RPREShoot, BWIDTH,FRF •Display:7"TFT 16K Color LCD,800*480 dots

Manufacturer: EZ DIGITAL Brand: EZ Digital

20MHz, 2-Channel Dual Trace Analog Oscilloscope Features DC to 20MHz bandwidth, 2 channels, Dual trace 6" rectangular CRT with internal graticule Sensitivity: 1mV/div ALT triggering function in VERT mode CH2 polarity inversion switch High sensitivity X-Y mode Sweep magnification (x10) TV synchronization with separator circuit for stable TV signal observation 400V maximum input voltage Size: 12.4"W x 5.63"H x 16.0"L (316mm(W) x 143mm (H) x 406mm (L)) Weight: 17.2 lbs. (7.8kg) Includes: User's manual, 2 spare fuses, power cord

Manufacturer: Fluke Corporation Brand: Fluke Model: FLK-VT04-HVAC-KIT

FLUKE VISUAL INFRARED THERMOMETER KIT

Manufacturer: Tektronix Brand: Tektronix Model: 2246A

The 2246A is a 100 MHz, four-channel, dual-sweep, portable oscilloscope for general-purpose use. A microprocessor -based operationg system controls most of the functions in the instrument, including a fully integrateed menu drvien voltge and time measurement system with Smartcursors, Other features include single-button automatic front panel setup and a menu driven store/recall setup function. A menu-driven service mode provides for configuring of certain menu and readout displays, internal calibration and servicing diagnostics.