Differential Pressure Gauges - Page 39

Manufacturer: Dwyer Instruments Brand: Dwyer Model: 2-5000-500PA

Combining clean design, small size and low cost with enough accuracy for all but the most demanding applications our Minihelic II gage offers the latest in design features for a dial type differential pressure gage. It is our most compact gage but is easy to read and can safely operate at total pressures up to 30 psig. The Minihelic II gage is designed for panel mounting in a single 2-5/8" diameter hole. Standard pressure connections are barbed fittings for 3/16" ID tubing; optional 1/8" male NPT connections are also available. Over-pressure protection is built into the Minihelic II gage by means of a blow-out membrane molded in conjunction with the diaphragm. Accidental over-ranging up to the rated total pressure will not damage the gage. With removable lens and rear housing, the gage may be easily serviced at minimum cost. With the housing molded from mineral and glass filled nylon and the lens molded from acrylic, the gage will withstand rough use and exposure as well as high total pressure. The 5% accuracy and low cost of the Minihelic II gage make it well-suited for a wide variety of OEM and user applications. OEM applications include cabinet air purging, medical respiratory therapy equipment, air samplers, laminar flow hoods, and electronic air cooling systems. As an air filter gage, the Minihelic II gage finds many end use applications on large stationary engines, compressors, ventilators, and air handling units. The Minihelic II gage is suitable for many of the same applications as the Magnehelic gage where the greater accuracy, sensitivity, and higher and lower differential pressure ranges of the Magnehelic gage are not required.

Manufacturer: Dwyer Instruments Brand: Dwyer Model: 2-5060

Combining clean design, small size and low cost with enough accuracy for all but the most demanding applications our Minihelic II gage offers the latest in design features for a dial type differential pressure gage. It is our most compact gage but is easy to read and can safely operate at total pressures up to 30 psig. The Minihelic II gage is designed for panel mounting in a single 2-5/8" diameter hole. Standard pressure connections are barbed fittings for 3/16" ID tubing; optional 1/8" male NPT connections are also available. Over-pressure protection is built into the Minihelic II gage by means of a blow-out membrane molded in conjunction with the diaphragm. Accidental over-ranging up to the rated total pressure will not damage the gage. With removable lens and rear housing, the gage may be easily serviced at minimum cost. With the housing molded from mineral and glass filled nylon and the lens molded from acrylic, the gage will withstand rough use and exposure as well as high total pressure. The 5% accuracy and low cost of the Minihelic II gage make it well-suited for a wide variety of OEM and user applications. OEM applications include cabinet air purging, medical respiratory therapy equipment, air samplers, laminar flow hoods, and electronic air cooling systems. As an air filter gage, the Minihelic II gage finds many end use applications on large stationary engines, compressors, ventilators, and air handling units. The Minihelic II gage is suitable for many of the same applications as the Magnehelic gage where the greater accuracy, sensitivity, and higher and lower differential pressure ranges of the Magnehelic gage are not required.

Manufacturer: JH Gauge Brand: JH Gauge

DIFFERENTIAL PRESSURE GAUGE 0-0.50 INCH W.C.

Manufacturer: Mid-West Instrument Brand: Mid-West Instrument Model: 120-AA-00-O(CA)

Mid-West Instrument piston type differential pressure gauge. Simple, rugged, compact design. Over-range protection to maximum pressure. Weather resistant construction standard. Shatter resistant acrylic lens. A low cost differential pressure gauge for use in measuring the pressure drop across filters, strainers, separators, valves, pumps, chillers, etc., and for local flow indication and control. Proof pressure: two times rated working pressure at ambient temperature. Aluminum body material. Stainless steel internal metal part. Buna-N seal material. 1/4-inches FNPT back connections, 2-1/2-inches uni-directional round dial, weather resistant engineered plastic case, accuracy +/-2 percent full scale (ascending). One switch in standard enclosure with 1/4-inches FNPT electrical connection NEMA 4X. SPDT 3W, 0.25 Amp, 125 VAC/VDC (standard) (switch adjustable range of 10-90 percent).

Manufacturer: LGSY Brand: LGSY

XL-802B Small and Convenient Pizoresistive Pressure Transmitter of Functional Specifications Measurement Range: 0~1KPa~60MPa Accuracy: ±0.5%FS Power Supply: 18~32VDC (24VDC) Nonlinear:＜±0.2%FS Output: 4~20mA two-wire system Stability: ≤±0.1%FS/year Pressure Gauge Connection: 1/2 " 1/4 " M20X1.5 (optional) Responding time: ＜30mS Application Small and convenient XL-802C LED display pressure transmitter including XL80A,B,C,D Four Types.The pressure transmitter Adopt imported sensor,A highly integration with sensors and integrated circuit,All stainless steel as a whole.zero point circuit and transmission gain no adjustment.with strong anti-interference capacity and anti-erode and longtime stability. Features Easy Installation Simplified Structure and Light Volume Piezoresistive Sensor of Imported Ceramic in Europe It can measure measurement range / vacuum / Absolute pressure apply to compatible with contact equipment quality of gas and liquid medium apply to Air compressor machine,hydraulic machinery,All kinds of pumps and thewater treatment plant and so on

Manufacturer: TechnologyLK Brand: TechnologyLK

Range is from 0-35 Pounds Door Pressure Gauge instrument design specifically to measure force. OPERATING INSTRUCTIONS Set the top (small) o-ring located on the plunger rod on zero, down against the instrument's flange; or set the o-ring on the desired force. Holding the instrument firmly, press slowly against the door at a point approximately handle-high, and 30 inches away from the door's hinges. Read the amount of force required to open the door on the plunger scale closest to the bottom of the small o-ring. MEET ADA REQUIREMENTS The Americans with Disabilities Act requires that both interior and exterior doors of a building be handicapped accessible. Door Opening Force (4.1311 ADAAG). Exterior hinged doors:(Reserved) Interior hinged doors:5 lbs (22.2N) Sliding or folding doors:5 lbs (22.2N) Automatic/Power Assisted Doors:(4.13.12) Such doors shall not open to back check faster than 3 seconds and shall require no more than 15 lbs (66.6N) to stop door movement. If a power assisted door is used, its door-opening force shall comply with 4.13.11 and its closing shall conform to the requirements in ANSI A156.19-1984. Plastic Protective Tube for Door Pressure Gauge. Size:8" long 7/8" diameter Includes: Three Door Pressure Gauge, 0-35 Lbs Three Plastic Protective Tube

Manufacturer: Dwyer Instruments Brand: Dwyer Model: DM-1104

The DigiMag Series DM-1000 Digital Differential Pressure and Flow Gages monitor the pressure of air and compatible gases just as its famous analog predecessor the Magnehelic Differential Pressure Gage. All models are factory calibrated to specific ranges. The 4-digit LCD can display readings in common English and metric units so conversions are not necessary. The simplified four button operation reduces set up time and simplifies calibration with its digital push button zero and span.

Manufacturer: WIKA Instrument Corporation Brand: WIKA Model: 50807099

The WIKA differential low pressure gauge has a circular dial that is 4" in diameter and is enclosed in a thermoplastic case with a polycarbonate window for increased durability in low temperature environments. The gauge measures pressure from 0.02 to 50 inch water column (inWC) and is accurate to + or - 3 percent of span over the entire range of the gauge. The female connection is a hosed barb that is made of plastic for increased durability. The gauge can be mounted and dismounted easily without the use of tools. The low pressure gauge is suitable for measuring differences of pressure in isolation chambers and for monitoring blowers and ventilators.Pressure gauges are instruments used to measure the pressure of a gas or liquid inside a vessel and, often, to help ensure the optimal amount of pressure for a given application. Pressure gauges can range from everyday instruments, such as those used to measure the air pressure in a car or bicycle tire, to highly accurate gauges used in mechanical and industrial processing. Most often, pressure gauges measure pressure relative to another reference. For instance, gauge pressure measures pressure relative to ambient air. An example of a pressure gauge measuring relative to ambient air is a tire pressure gauge or a blood pressure gauge. Differential pressure is the difference in pressure between two points, such as when measuring liquid flow along various points in a pipeline. An absolute pressure gauge measures pressure relative to a perfect vacuum, such as an atmospheric or barometric pressure gauge. All types of pressure gauges include either a male or a female mount to connect to the vessel where pressure is being measured, and display results on a dial with varying increments of measure across a given range.WIKA Instrument Corporation is a global manufacturer of pressure and temperature measurement instruments, including pressure gauges, diaphragm seals, pressure transmitters, and thermometers, that meet International Organization for Standardization (ISO) standards...

Manufacturer: Dwyer Instruments Brand: Dwyer Model: ISDP-016

The ISDP Differential Pressure Transmitter provides a 4-20 mA process output, a robust NEMA 4X enclosure, plus a large LCD display that can be programmed to read in pressure, velocity or flow. The ISDP offers simplified programming via a Menu key that enables the user to select: security level; English or Metric engineering units; pressure, velocity or flow operation, K-factor for use with various Pitot tubes and flow sensors, circular or rectangular duct size for volumetric flow operation plus many more. The Series ISDP Differential Pressure Transmitter is powered on its two wire loop with 10-35 VDC via its integral M-12 four pin male connector. The ISDP provides a 0.5% full scale accuracy on ranges from 0.25" WC to 100" WC as well as bi-directional models up to 10" WC These features make the Series ISDP Differential Pressure Transmitter the ideal instrument for monitoring pressures or air flows in hazardous zones having a Class I Div. I Groups A, B, C, D; Class II Div. I Groups E, F, G; Class III Div. I ratings.

Manufacturer: Dwyer Instruments Brand: Dwyer Model: 616-10B

Series 616 Transmitter features an exceptional ±0.25% accuracy in several factory calibrated ranges. Choose the one just right for your application. Span and Zero controls included for fine tuning and minor re-calibration in the field.