Calibration - Page 103

Manufacturer: Martel Electronics Brand: Martel Electronics Model: 1919611

As with the original high accuracy BetaGauge P.I. PRO gauges, the BetaGauge PIR PRO takes the concept of a simple analog Test Gauge and combines it with the accuracy of digital technology. The new Reference Class gauges provide exceptional performance with ±0.04% of reading accuracy, especially when operated below 50% of their range. The BetaGauge PIR PRO builds on the proven performance of the BetaGauge PIR with a new purpose designed Zinc-Aluminum Alloy High Pressure Cast housing. The new housing improves the environmental integrity of the gauge in a lighter and smaller yet more rugged form factor

Manufacturer: ABS Import Tools, Inc. Brand: HHIP Model: 4401-3624

HHIP grade a ledge 0 black granite surface plate is checked by an auto-collimator for overall accuracy assurance. Granite surface plates meet or exceed Federal specifications ggg-p-463c. Includes a certificate of inspection. Accuracy is +/-.0001". it measures 36" Length by 24" width by 4" height.

Manufacturer: Fluke Corporation Brand: Fluke Model: I6000S FLEX-36

The i6000sflex is an AC current probe utilizing the Rogowski principle. It can be used to measure currents up to 6000A when used in conjunction with oscilloscopes, recorders or data loggers. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas. Current ranges: 60A/600A/6000A AC rms. Output sensitivity (AC coupled): 50 mV /5mV / 0.5mV per A. Load impedance: 100 k ohm minimum. Accuracy (at +25 degree C): +/-1 percent of range (45 - 65 Hz). Linearity (10 to 100 percent of range): +/-0.2 percent of reading. Noise: 8mV AC rms (60 A), 2 mV AC rms (600/6000A). Frequency range: 10 Hz to 50 kHz (- 3 dB). Phase error: < +/-1 degree (45 – 65Hz), +/-10 degree (at 20 kHz). Position sensitivity (with cable > 25mm from the coupling): +/-2 percent of range. External field (with cable > 200mm from the head): +/-1 percent of range. Power supply: 2 x AA MN 1500 LR6 alkaline 400 Hours, low battery indicator or dedicated ext power supply. Temperature coefficient: +/-0.08 percent of reading per degree C. Working voltage: 600 V AC rms or DC. Head cable diameter: 14.3mm. Cable length (head to electronics): 2 meters. Operating temperature range: -20 to +90 degree C (head), -20 to +85 degree C (electronics). Storage temperature range: -40 to +105 degree C (head), -20 to +85 degree C (electronics). Operating humidity: 15 to 85 percent (non condensing).

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-709

The Fluke 709 Precision Loop Calibrator and 709H Precision HART Loop Calibrator (the Product or the Calibrator) can be used for installation, calibration, and troubleshooting of field transmitters, valves, and other control system components at process plants. Primary functions are source and measure mA signals in the 0 mA to 24 mA range. The Product can measure 0 V to 30 V and produce 24 V dc loop power.

Manufacturer: Tel-Tru Manufacturing Company Brand: Tel-Tru Model: Check-Set I, 40°F, w/310 well

Tel-Tru Check-Set I Thermometer Calibrator, 40 Degree Fahrenheit, Nist Traceable, Removable well with 3 Probe Diameter Holes 0.187"/0.250"/0.375", Stainless Steel Housing, Input power 115 volts, 50/60 Hz 1.5 amps

Manufacturer: Yokogawa Electric Corporation Brand: Yokogawa Model: CA12E-2

Temperature Calibrator with Rubber Boot, Strap and Accessory Case; Signal source: TC (10 kinds), RTD, DC100 mV, 4000; Measurement: TC (10 kinds), RTD, DC100 mV, 4000; Selectable RTD (Pt100 or JPt100), Built-in RJC

Manufacturer: ABS Import Tools, Inc. Brand: HHIP Model: 4401-1604

HHIP grade b ledge 0 black granite surface plate is checked by an auto-collimator for overall accuracy assurance. Granite surface plates meet or exceed Federal specifications ggg-p-463c. Includes a certificate of inspection. Accuracy is +/-.0004". it measures 48" Length by 36" width by 6" height.

Manufacturer: Reed Brand: REED Instruments Model: BX-150

Closed loop microprocessor based digital PID temperature controller system incorporating a heater and a precision platinum RTD sensor. Fan cooling allows rapid changes in block temperature upon demand. Required temperature may be adjusted in 0.1 degree increments using front panel buttons. Temperature range: 33 to 300 degree C. Resolution: 0.1 degree C/degree F. Accuracy: +/-0.8 degree C (+/-1.6 degree F) less than or equal to 100 degree C (less than or equal to 212 degree F); +/-1.6 degree C (+/-3.2 degree F): 100-200 degree C (212-392 degree F); +/-2.8 degree C > 200 degree C (> 392 degree F). Stability: +/-0.1 degree C (+/-0.2 degree F) less than or equal to 100 degree C (212 degree F); +/-0.2 degree C (+/-0.4 degree F) 100-200 degree C(212-662 degree F); +/-0.4 degree C (+/-0.8 degree F) >200 degree C (>392 degree F). Time to stability: 10 to 20 minutes. Heating time: 30 minutes to maximum. Cooling time: 30 minutes to 100 degree C (212 degree F). Power supply: 110VAC (+/-10 degree), 2.5A. Well diameters: 1 by 1/4", 1 by 3/16", 1 by 5/32", 2 by 1/8". Well depth: 90mm.

Manufacturer: Fluke Calibration Brand: Fluke Model: 5615-9-P

For those needing faster thermal response, or where diameter and immersion depth are problems. These probes are excellent reference probes for comparison calibrations in a Fluke Calibration dry-well. A printout of sensor resistance is provided in 1 °C increments for each probe. The 5615-9 are calibrated from –196 °C to 420 °C. We’ve tested many of the probes on the market. We’ve used them in our manufacturing facility and tested them in the lab, and this is an excellent secondary standards PRT. Other instruments on the market are priced much higher, have lower stability, or are of lower quality.

Manufacturer: Starrett Brand: Starrett Model: 81565

Angle plates provide a convenient and practical means of clamping and holding work in a vertical position. Their excellent finish and flatness make them very compatible for use with granite surface plate accuracies. The angle plates are available with either 2 or 4 finished faces. The 2-face angle plate has the bottom and the adjacent square face finished flat and square to one another. The 4-face is similar to the 2-face, but has the two adjacent sides finished flat and square to the other two faces, as well as being parallel to each other.