Calibration - Page 168

Manufacturer: Tuthill Brand: Fill-Rite Model: KIT800GR

Built into every fuel transfer pump, chemical transfer pump and meter is over 50 years of experience—and the pride and workmanship associated with the moniker “Made in USA”. We use only the most durable materials to insure long life and dependability. Fill-Rite and Sotera branded products deliver superior performance time and time again, regardless of the application or installation.

Manufacturer: Arco Electronics Limited Brand: Smart Sensor Model: AS510 Color: Black

• Measuring Range: 0~100hPa \ 0~40.15inH²O• Resolution: Resolution: 0.01hPa \ 0.01inH²O• Accuracy: ±0.03hPa(0~0.30hPa) \ ±0.05hPa(0.31~1.0hPa) \ ±(1.5%+0.1hPa) \ ±0.01inH²O(0.00~0.12inH²O) \ ±0.02inH²O(0.13~0.40inH²O) \ ±(1.5%+0.4inH²O)• Sampling Time: 0.5 sec• Unit Selection: Pa, hPa, mbar, mmH²O, mmHg, inHg, inH²O, psi, m/s, fpm• Operating Environment: 0~50°C, 32~122°F PACKING INFORMATIONPower: 3*1.5V AAA: BatteryProduct Net Weight: 180gProduct Size: 159*66*33mm Packing Style: Gift BoxQ'ty Per Carton: 40pcsGW Per Carton: 12.5kgStandard Carton Size: 52.5*40*49cm

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 613658-551 Color: Ceramic

The Mitutoyo grade AS-2 rectangular gage block is made of ceramic, has its nominal length engraved in metric [millimeter (mm)] units, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade AS-2 gage block is commonly used in workshops for calibrating and inspecting mounting tools and cutters. It is made of ceramic, which resists corrosion, abrasion, and burrs, can withstand high temperatures without melting (high thermal expansion resistance), and provides dimensional stability. This gage block has a rectangular base for accurate wringing. Nominal length is measured in metric [millimeter (mm)] units, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 9 millimeters. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measuring equipment and to standardize the measurement of length in manufacturing industries. They are commonly made of...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 614622-531

The Mitutoyo grade 0 square gage block is made of steel, has its nominal length engraved in metric [millimeter (mm)] units, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 0 gage block is commonly used in workshop and inspection applications to calibrate and inspect mechanical parts and tools, to verify the accuracy of plug and snap gages, and to set electronic measuring devices. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear resistance. This gage block has a square base for accurate wringing, to attain a height reference standard, and for the ability to make a dedicated inspection jig. Nominal length is measured in metric [millimeter (mm)] units, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 24.1 millimeters. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 614219-521

The Mitutoyo grade 00 square gage block is made of steel, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 00 gage block is commonly used within a controlled environment as a reference standard for setting high-precision measuring equipment, to calibrate low-grade gage blocks, and to inspect the accuracy of gages, mechanical parts, and tools. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear-resistance. This gage block has a square base for accurate wringing, to attain a height reference standard, and for the ability to make a dedicated inspection jig. Nominal length is measured in inches, and indicated on the block with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.95 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibr...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 619051

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 614619-521

The Mitutoyo grade 00 square gage block is made of steel, has its nominal length engraved in metric [millimeter (mm)] units, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 00 gage block is commonly used within a controlled environment as a reference standard for setting high-precision measuring equipment, to calibrate low-grade gage blocks, and to inspect the accuracy of gages, mechanical parts, and tools. It is made of ceramic which resists corrosion, abrasion, and burrs, withstands high temperatures without melting (high thermal expansion resistance), and provides dimensional stability. This gage block has a square base for accurate wringing, to attain a height reference standard, and for the ability to make a dedicated inspection jig. Nominal length is measured in metric [millimeter (mm)], and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 24.1 millimeters. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 614649-521

The Mitutoyo grade 00 square gage block is made of steel, has its nominal length engraved in metric [millimeter (mm)] units, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 00 gage block is commonly used within a controlled environment as a reference standard for setting high-precision measuring equipment, to calibrate low-grade gage blocks, and to inspect the accuracy of gages, mechanical parts, and tools. It is made of ceramic which resists corrosion, abrasion, and burrs, withstands high temperatures without melting (high thermal expansion resistance), and provides dimensional stability. This gage block has a square base for accurate wringing, to attain a height reference standard, and for the ability to make a dedicated inspection jig. Nominal length is measured in metric [millimeter (mm)], and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 24.1 millimeters. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks...

Manufacturer: Mettler Toledo Brand: Mettler Toledo

A customized 3rd weight for your Mettler Toledo CarePacs. Use the OIML Class E2 2 milligram weight to perform customized testing such as minimum weight determination. The 3rd weight perfectly fits into your CarePac carrying case.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 613219-541

The Mitutoyo grade AS-1 rectangular gage block is made of ceramic, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. The grade AS-1 gage block is commonly used for workshop and inspection applications to calibrate fixtures and precision instruments, to inspect a variety of tools such as mounting tools, cutters, fixtures, and mechanical parts, and for manufacturing gage applications. It is made of ceramic which resists corrosion, abrasion, and burrs, withstands high temperatures without melting (high thermal expansion resistance), and provides dimensional stability. This gage block has a rectangular base for accurate wringing. Nominal length is measured in inches, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.355 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measuring equipment...