Current Clamps - Page 7

Manufacturer: Yokogawa Brand: Yokogawa

Yokogawa Model 251-100 KmKm Panel Meter

Manufacturer: Kyoritsu Brand: Kyoritsu Model: 8125

Kyoritsu 8125 load current clamp sensor. In order to monitor energy saving and to control the electric facilities, it is essential and imperative to control the leak and load currents from mains and branch power lines up to the equipment. Clamp sensor is easy to carry and simple to install. Load current detection type clamp sensors provide superior characteristic in phase for the use of power meter. Rated current 500Amp AC. 40mm conductor size. Output voltage: AC 500mV/500A (AC 1mV/A). Accuracy: +/- 0.5 percent rdg +/- 0.1mV (50/60Hz), +/- 1.0 percent rdg +/- 0.2mV (40Hz to 1kHz). Phase shift within +/- 1.0 degree. Output connector: Mini-DIN 6-pin. 0 to 50 degree c temperature range. Withstand voltage: 5350V AC for 5 seconds. Approximate 3m cable length. Approximate 2 ohm output impedance. Accessories includes: portable case, instruction manual, cable marker. Measures 128 mm length by 81 mm width by 36mm depth.

Manufacturer: Hioki Brand: Hioki Model: 9669

Clamp on sensors for the power quality analyzer 3196 and clamp on power HiTester 3169. Sensors are designed with a safety barrier to protect the user from being in direct contact with live conductors. Completely meet all CE marking requirements. Rated input current 500 Amp AC, 5000 Amp AC. Rated output current 0.5 V AC. Accuracy (at 45/66 Hz) amplitude: +/-1.0 percent rdg. +/-0.01 f.s. Full scale (f.s.) is the 3196 range value. Phase: +/-1 or less. Frequency characteristics 66 Hz to 5 kHz (+/-1 percent or less from accuracy). Maximum allowable input continuous 1000 A rms (45 to 66 Hz). Maximum circuit voltage 600 V AC rms (insulated wire). Core jaw diameter: 2-5/32", 3-9/64" by +/-25/32" busbar. Measures 3-29/32 width by 7-25/64" height by 1-41/64" depth. 9-53/64' Cord length.

Manufacturer: Fluke Corporation Brand: Fluke Model: I200 Color: Multicolored

Fluke Current clamps are the ideal tools to extend the current ranges of Multimeters. The i200 is a single range 200A ac current clamp with current output via safety shrouded banana plugs. The i200 is compatible with most Fluke multimeters or any other current measurement device that accepts shrouded banana plugs. Companion to a DMM to measure up to 200A AC. 1mA per Amp output guarantees easy reading on you meter. Take accurate current readings without breaking the circuit. Maximum conductor diameter 20mm. CAT III 600V safety rating. Nominal current range: 200 A. Continuous current range: 0.5 A - 200 A. Maximum non-destructive current: 240 A. Lowest measurable current: 0.5 A. Basic accuracy: 1 percent + 0.5 A, (48-65 Hz), (percent reading + floorspec). Useable frequency: 40 Hz - 10 kHz. Output levels: 1 mA/A. Maximum conductor diameter: 20mm. Maximum conductor size (busbar): 20 x 5mm. Output cable length: 1.5 m. With shrouded banana plugs.

Manufacturer: Fluke Brand: Fluke Model: i400 Color: Multicolored

Fluke Current clamps are the ideal tools to extend the current ranges of Multimeters. The clamp is a single range ac current clamp with current output via safety shrouded banana plugs. The clamp is compatible with most Fluke multimeters or any other current measurement device that accepts shrouded banana plugs. 1mA per Amp output guarantees easy reading on you meter. Take accurate current readings without breaking the circuit.

Manufacturer: Hioki Brand: Hioki Model: CT 6500

Clamp on sensor use with the Clamp Logger. Primary: AC 500 A; 40 Hz to 1 kHz. Secondary: AC 1mV/A. Maximum input current: AC 600 A. 46mm diameter.

Manufacturer: UEi Brand: UEi Test Instruments Model: DL379 Color: Black, Yellow

4000uF Capacitance, 2000 uA AC/DC, Non-Contact Voltage 24~600VAC, 750VAC/1000VDC, 400A AC, min/max, -22 to 752 degrees Fahrenheit, 40M Ohms resistance, frequency duty cycle, diode, data hold,

Manufacturer: Vetus Brand: ETCR

Technical Specification Function:Measurement of AC leakage current, AC current and on-line measurement Power: Zn-Mn dry battery,6F22,9V Size of clamp: Φ68mm Range: 0.00mA~1200A Resolution: 0.01mA Accuracy(23°C±3°C, below 70%RH): 0.00mA~59.9A: ±1.5%±5dgt; 60.0A~199A: ±2%±5dgt; 200A~599A: ±3%±5dgt; 600A~1200A: ±4%±5dgt Test Mode: Clip-on CT, integral mode Display Mode: Four digits LCD display Dimension: HxWxT:224mmX115mmX43mm LCD Dimension: 35mm×21.5mm;display domain:32mm×15mm Sampling Rate: about 2 times/s Range Shift: Automatically Voltage Range: AC600V USB Interface: Data stored in the memory of the meter via USB upload to PC, or on-line monitoring USB line:1.5m Storage: 99units,all used when display FULL Peak Hold: Push HOLD without release, the meter will show the peak value during the pushing period Reading Hold: mDH indicating the reading is hold Out of Range: OL indicating the current is out of range Auto Power-off: 5 Minutes after power on, it will power off automatically to lower the power consumption Battery Voltage: Indicating the battery voltage is lower than 7.2V.Then the battery have to be changed Consumption: About 15mW Temperature and Humidity: Working: -10℃～40℃,below 80%rh; Storage: -10℃～60℃,below 70%rh Insulating Strength: AC2kV/rms.(between the alloy of the clamp and the housing) Applicable Safety Rules: IEC1010-1,IEC1010-2-032,pollution, etc 2,CAT 3(600V) Accessories: Meter: 1pc;USB communication line:1 pc; disk: 1 pc; bag: 1pc

Manufacturer: Kyoritsu Brand: Kyoritsu Model: 8124

Kyoritsu 8124 load current clamp sensor. In order to monitor energy saving and to control the electric facilities, it is essential and imperative to control the leak and load currents from mains and branch power lines up to the equipment. Clamp sensor is easy to carry and simple to install. Load current detection type clamp sensors provide superior characteristic in phase for the use of power meter. Rated current 1000Amp AC. 68mm conductor size. Output voltage: AC 500mV/1000A (AC 0.5mV/A). Accuracy: +/- 0.5 percent rdg +/- 0.1mV (50/60Hz), +/- 1.0 percent rdg +/- 0.2mV (40Hz to 1kHz). Phase shift within +/- 1.0 degree. Output connector: Mini-DIN 6-pin. 0 to 50 degree c temperature range. Withstand voltage: 5350V AC for 5 seconds. Approximate 3m cable length. Approximate 1 ohm output impedance. Accessories includes: portable case, instruction manual, cable marker. Measures 186 mm length by 129 mm width by 53mm depth.

Manufacturer: Fluke Corporation Brand: Fluke Model: 4637337

Fluke 12 inch iFlex flexible current probes measure to 1500A AC while providing the ultimate measurement flexibility. The iFlex probes connect directly to the energy logger, displaying current measurements without error prone scaling factors. The 1.8 m (6 ft.) cord allows separation between the measurement location and the energy logger making it easier to view the display.