Flowmeters - Page 3

Manufacturer: The Harris Products Group Brand: Harris Model: 3100200

The Model 355-2 incorporates a regulator and flowmeter into one compact unit. The flow tube and float are easily changed for different gases. As supplied, the flow tube has dual calibration. It includes a sensitive needle valve for finger tip control.

Manufacturer: Blue-White Brand: Blue-White Model: F30200P

Blue-White F30200P Acrylic Meter Body Flowmeter for 2" PVC Pipe 40-150 GPM

Manufacturer: DIGITEN Brand: DIGITEN

Features: Easy to install,size is small. Can connect to flow sensor,temperature sensor,solenoid valve.monitor gases,liquid flow.quantitative flow control,total flow alarm. Monitor real-time flow rate. Display temperature of the liquid.need to extra add temp sensor. Control quantitative flow.when flow reach to the presetting flow,system will output signal to solenoid valve(ON/OFF). Monitor total flow,total flow alarm. Password can protect setting value. When flowmeter is working,faucet dynamic display. You can set K constant for various of flowmeters. Specification: Power adapter: input AC100-240V; Output: DC24V Working volt: DC24V±8V/1A Flow range:10-200L/min LCD size:3 inch,built-in backlight. Viewing Angle:0-120 degree. Solenoid valves working voltage:DC12V/0.3-0.5A(NC) Controller case size:103x77x35mm,Controller cutout size:98x73mm. Package Includes: 1 x LCD flow display controller 1 x G2" flow sensor 1 x AC100-240V power adapter 1 x Temperature sensor 1 x Instruction

Manufacturer: Elster AMCO Brand: Scancounter

Wired Remote Reader. The ScanCounter T210 electronic outreader is designed specifically for accurate counting of meter pulse outputs. It incorporates an easy to read display. Inexpensive and reliable, the ScanCounter T210 is a cost effective solution to meter reading access problems. The ScanCounter T210 is installed in a location easily accessed by the meter reader. Connected to the meter pulse output by wire, the T210 accumulates pulses from the meter and stores the reading.

Manufacturer: Racine Federated Brand: Hedland Model: H621-004-R

EZ-View flow meters for water. EZ to install, in any position. Radel R for more aggressive media. No special piping or flow straighteners needed. No electrical connections. Direct reading indication. Accuracy within 5 percent full scale. Relatively insensitive to shock and vibration. Materials: Radel R plastic body and cone, polysulfone piston. Common parts are T300-series stainless spring, Buna N indicator ring, Buna N pressure seals, plastic polysulfone fittings, Polypropylene limit indicators, PH15 - 7MO stainless retaining ring. Optional are Teflon coated spring and retaining ring. NPT ANSI/ASME B1.20.1, BSPT ISOR7 fittings/ threads.

Manufacturer: Norgas Brand: Norgas

200 CFH Norgas NG4 Gas Meter with 1 CF pulse output. 3/4 NPT Top Connections are built into the meter. The NG4 diaphragm gas meter is made to measure accurately submetering applications of gas appliances. The aluminum construction along with the sealed register allows it to be installed in many applications. The pulse output allows for integration of remote counters and transmitters.

Manufacturer: Dwyer Instruments, Inc. Brand: Dwyer

Dwyer® Series WMT2 Multi-Jet Water Meter is ideal for commercial and industrial applications. The multi-jet design allows simplicity and accuracy with wide flow ranges even in low flow applications. The meter is designed for long service life and relatively maintenance-free operation, even under adverse conditions. The magnetically driven, hermetically sealed register will not leak or fog and is completely separated from the water. The reed switch is activated by a magnet on the dial, which is directly proportional to the flow rate. The output is perfect for remote monitoring of flow rate or flow totalization, and can interface with PLC's, counters, data loggers, and SCADA systems. Note: NOT FOR POTABLE WATER USE, BRASS CONTAINS LEAD IN EXCESS OF LOW LEAD LIMITS. (Standard range shown in picture).

Manufacturer: Dwyer Instruments, Inc. Brand: Dwyer

Dwyer® Series WMT2 Multi-Jet Water Meter is ideal for commercial and industrial applications. The multi-jet design allows simplicity and accuracy with wide flow ranges even in low flow applications. The meter is designed for long service life and relatively maintenance-free operation, even under adverse conditions. The magnetically driven, hermetically sealed register will not leak or fog and is completely separated from the water. The reed switch is activated by a magnet on the dial, which is directly proportional to the flow rate. The output is perfect for remote monitoring of flow rate or flow totalization, and can interface with PLC's, counters, data loggers, and SCADA systems. Note: NOT FOR POTABLE WATER USE, BRASS CONTAINS LEAD IN EXCESS OF LOW LEAD LIMITS. (Standard range shown in picture).

Manufacturer: Dwyer Instruments, Inc. Brand: Dwyer

Dwyer® Series WMT2 Multi-Jet Water Meter is ideal for commercial and industrial applications. The multi-jet design allows simplicity and accuracy with wide flow ranges even in low flow applications. The meter is designed for long service life and relatively maintenance-free operation, even under adverse conditions. The magnetically driven, hermetically sealed register will not leak or fog and is completely separated from the water. The reed switch is activated by a magnet on the dial, which is directly proportional to the flow rate. The output is perfect for remote monitoring of flow rate or flow totalization, and can interface with PLC's, counters, data loggers, and SCADA systems. Note: NOT FOR POTABLE WATER USE, BRASS CONTAINS LEAD IN EXCESS OF LOW LEAD LIMITS. (Standard range shown in picture).

Manufacturer: Blue-White Brand: Blue-White Model: F30400P

F-300 series flow meters utilize a pitot tube pick up and a hard edged float design to provide a convenient and economic means of measuring water flow in a closed pipe system. The F-300 impact tube flow meter features a tough, one-piece machined acrylic meter body, corrosion resistant internal parts, and permanent screen-printed scale. You get all the strength and long service life required in most commercial and industrial applications. Flowmeters are installed after the filtration system in Commercial Pool applications. This enables the service persons, or Health Inspector to tell at a glance if the recirculating pump is pushing an adequate amount of water to ensure optimum water turnover (filtration).