Electrical Testing - Page 639

Manufacturer: Keysight Technologies Brand: KEYSIGHT TECHNOLOGIES Model: DSOXLAN

LAN/VGA module gives you network connectivity and complete LXI compliant support as well as the ability to connect to an external monitor. Operate your scope remotely from your PC using the web browser interface with the virtual front panel interface that looks and acts as the real front panel on the scope with the same associated keys and knobs. Oscilloscope are required.

Manufacturer: Mueller Electric Brand: Mueller Electric

Test Leads Black Insul Alligato

Manufacturer: RioRand Brand: RioRand Model: RR-02-LZ-DO

- Model: RR2102CEL - 7.0" LCD display - Bandwidth: 100MHz - Rise Time:

Manufacturer: Mueller Electric Brand: Mueller Electric

Test Clips GRN INSUL FOR 11C&A

Manufacturer: AFL/Noyes Brand: AFL/Noyes Model: CSM1-4

CSM1 Palm-sized Optical Power Meter The palm-sized CSM1 optical power meter accurately measures optical power in Premises Telco or Broadband fiber optic networks. Weighing only 0.4 lb this power meter is ideal for field use. The CSM1 stores optical references for each calibrated wavelength and features multiple test Tone detection for fiber identification. A large LCD display with backlight shows measured power [dBm or W] or insertion loss [dB] calibrated wavelengths [nm] tone frequency [Hz] and indicates a low battery condition. The CSM1 optical input port accepts a variety of NOYES thread-on style adapter caps (ordered separately) to meet a wide range of testing requirements. One adapter cap 2.5 mm Universal is included. Powered by two AA alkaline batteries the CSM1 offers a five-minute auto-off feature and over 300 hours of operation with backlight off. The CSM1 is fully N.I.S.T. traceable.  Noyes CSM 1 Power Meters PDF [658 KB]

Manufacturer: Compliance West Brand: Compliance West

HTT-1R MedmA, Function Checker, Ground (Pass 0.1 Fail 0.025 ohm) Leakage (Pass 848k Fail 424kohm) Arcover 750V ± 400V. The HTT-1R was designed to provide a fast, safe and reliable way to verify proper operation of Dielectric Withstand (hipot) and Ground Bond Testers between calibration cycles, using actual component values which mimic the product being tested. It provides a stringent periodic check of your production line hipot and ground bond testers as required by TUV and others. The HTT-1R functions like our successful HTT-1 tester, but goes a step further by providing component values as the test loads, instead of opens and shorts provided by the HTT-1. By choosing one of our standard configurations conforming to your testing parameters (or custom parameters based on your requirements), the hipot and ground bond tester in use are checked by realistic component values which mimic the characteristics of your production items. The HTT-1R verifies the result of the three failure modes encountered in production hipot and ground circuit testing (open ground, high leakage current, and dielectric breakdown) separately or in any combination to verify proper test equipment operation. A passing test can also be simulated. The HTT-1R is designed to test up to 30A ground bond testers using these values to simulate actual operation. Connections to the Ground Bond Tester will add approximately 0.03Ω to these values.

Manufacturer: Pico

The PicoScope 2405A is a 25MHz 4-channel oscilloscope that also features built-in spectrum analysis, function/arbitrary waveform generation and serial bus analysis. Sampling at a maximum of 500MSa/s, the 2405A has a buffer memory of 48ksamples and a 1MHz AWG signal generator. 15 automatic measurements are available in scope mode and another 11 in spectrum mode. Serial decoding (normally an extra cost on benchtop scopes) is included free for SPI, I2C, FlexRay, CANbus, LINbus, ARINC, and others. The PicoScope 2405A delivers great value for money, with excellent waveform visualization and measurement, as well as fast waveform update rates, giving the performance needed for advanced analysis of waveforms, including serial decoding and frequency plots.

Manufacturer: Pico

The PicoScope 2405A is a 25MHz 4-channel oscilloscope that also features built-in spectrum analysis, function/arbitrary waveform generation and serial bus analysis. Sampling at a maximum of 500MSa/s, the 2405A has a buffer memory of 48ksamples and a 1MHz AWG signal generator. 15 automatic measurements are available in scope mode and another 11 in spectrum mode. Serial decoding (normally an extra cost on benchtop scopes) is included free for SPI, I2C, FlexRay, CANbus, LINbus, ARINC, and others. The PicoScope 2405A delivers great value for money, with excellent waveform visualization and measurement, as well as fast waveform update rates, giving the performance needed for advanced analysis of waveforms, including serial decoding and frequency plots.

Manufacturer: YOKOGAWA Brand: Yokogawa

YOKOGAWA 103-111-FAFA CURRENT METER

Manufacturer: Pico Brand: Pico

Pico 2205 MSO KIT PicoScope with Analog and Digital Probes Full-Featured oscilloscope The picoScope 2205 mSo from pico technology is a 2+16 channel, 8-bit resolution oscilloscope. this means that along with 2 analog channels, the picoScope 2205 mSo also has 16 digital inputs, so you can view your digital and analog signals simultaneously. The picoScope 2205 mSo is a full-featured oscilloscope. A function generator and arbitrary waveform generator are built in and include a sweep function. it also offers mask limit testing, math and reference channels, advanced digital triggering, serial decoding, automatic measurements and color persistence display. Triggering The picoScope 2205 mSo offers a comprehensive set of advanced digital triggers including: pulse width, windowed and dropout triggers to help you capture the data you need. Digital triggering reduces timing errors and allows our oscilloscopes to trigger on the smallest signals, even at the full bandwidth. trigger levels and hysteresis can be set with high resolution. Digital triggering reduces rearm delay and, combined with the segmented memory, allows the triggering and capture of events that happen in rapid sequence. the mask limit testing function can then scan through these waveforms to highlight failed waveforms for viewing in the waveform buffer. The 16 digital inputs can be displayed individually or in arbitrary groups labelled with binary, decimal or hexadecimal values. A separate logic threshold from -5 V to +5 V can be defined for each 8-bit input port. the digital trigger can be activated by any bit pattern combined with an optional transition on any single input. Advanced logic triggers can be set on either the analog or digital input channels, or both. Selecting digital channels, or groups Selecting the digital channels in the software couldn't be easier. Just open the user interface, and then drag and drop to add the channels you want to see