Flowmeters - Page 66

Manufacturer: COLE-PARMER Brand: Cole-Parmer

These easy-view correlated flowmeters feature a wide viewing angle. The wide viewing angle lets you view flow tube and float from either front or side! Use rotating shield to magnify tube for precise readings. Ideal for measuring and regulating flow rates for analytical instruments or industrial chemical processes. Common applications include blending, mixing, and gas purging. Flowmeters are available with single- or dual-floats and include a valve to control flow. Choose new dual-float models for higher flow rates than the single-float models. Meters are available with aluminum or 316 stainless steel (SS) frames, valves, and fittings and all models feature a borosilicate glass tube and Buna-N O-rings (Stainless steel flowmeters have Viton O-rings). All meters include correlation charts for water and air. Correlation charts for oxygen, nitrogen, hydrogen, carbon dioxide, and helium are available from our Application Specialists upon request. Inlet and outlet ports are located on the back of the flowmeter to keep tubing out of the way (tubing is sold separately). Mount flowmeters vertically on a control panel or bench with tripod base (order separately). Easy to install and easy to read with 180° viewing New models with dual-floats allow a higher turndown ratio-better than 20:1

Manufacturer: Flomec Flow Meters Brand: Flomec Flow Meters

Flomec 01N series 3 - 30 gpm turbine def flow meter made from nylon rated to 150 psig pressure with 1" (F)NPT connection. Brand Name|Flomec#MFR Part Number|113255-24#UPC|031401001235#UNSPSC|41112501#Item|DEF Flow Meter#Connection Size|1 Inch#Flow Rate|3 - 30 gpm#Pressure Rating|150 psig#Connection Type|(F)NPT#Display Type|4-Digit LCD#Maximum Viscosity|5 cP#Sensor Type|Magnetic#Strainer Type|55 mesh#Power Source|(2) AAA Battery#Temperature Rating|14 - 131 deg F#Material|Nylon#Standard/Approvals|CE Certified

Manufacturer: Racine Federated Brand: Hedland Model: H671A-050

Flow Meter For Air and Other Compressed Gases. Direct reading. Install in any position. 360 degrees rotatable guard/scale. Easier-to-read linear scale. No flow straighteners or special piping required. Relatively insensitive to shock and vibration. Good viscosity stability. Temperature up to 240 degrees F. Accuracy +/-2 percent full scale. Repeatability +/-1 percent. Special scales available. Calibrated for 1.0 S.G. Materials: 2024 - T351 Anodized aluminum body, piston and cone. Common parts are Spider Plate: T316 SS, Spring: T302 SS, Fasteners: T303 SS, Pressure Seals: Viton, Guard: Polycarbonate, Retaining Ring: T316 SS, Retaining Spring: T316 SS, Indicator and Internal Magnet: PPS / Ceramic, Guard Seal / Bumper: Buna N, Scale Support: 6063 - T6 Aluminum and End Caps: Nylon ST.

Manufacturer: Great Plains Industries Brand: GPI® The Proven Choice® Model: 01N31LM

The GPI 01N31LM digital turbine water flowmeter is made from durable nylon and features an LCD display that is accurate to +/-5 percent of reading. This economical turbine meter is designed for flow rates from 10 to 100 LPM (3 to 30 GPM) and is factory calibrated in gallons for use with water. The lightweight 01N31LM mounts easily to the end of a hose and is ideal for use with free flow gravity systems or combined with an electric transfer pump as part of an irrigation or water management system. The GPI 01N31LM digital flow meter has 1-inch FNPT inlet/outlet and comes with two standard AAA batteries.

Manufacturer: Flomec Flow Meters Brand: Flomec Flow Meters

Flomec MR 5-30 series 5 - 30 gpm nutating disc mechanical fuel meter made from aluminum rated to 50 psi pressure with 1" BSPP connection. Brand Name|Flomec#MFR Part Number|126300-43#UPC|031401001068#UNSPSC|41112501#Item|Mechanical Fuel Meter#Connection Size|1 Inch#Flow Rate|5 - 30 gpm#Pressure Rating|50 psi#Master Totalizer|999999.9 gal#Connection Type|BSPP#Display Type|4-Digit Batch, 8-Digit Total#Temperature Rating|-20 to 125 deg F#Dimensions|7 Inch Length x 6-1/4 Inch Width x 5-7/8 Inch Height#Material|Aluminum#Includes|90 deg Fitting Adapter#Standard/Approvals|UL Listed

Manufacturer: Blue-White Brand: Blue-White

F-300 series flow meters utilize a pitot tube pick up and a hard edged float design to provide a convenient and economic means of measuring water flow in a closed pipe system. The F-300 impact tube flow meter features a tough, one-piece machined acrylic meter body, corrosion resistant internal parts, and permanent screen-printed scale. You get all the strength and long service life required in most commercial and industrial applications. Flowmeters are installed after the filtration system in Commercial Pool applications. This enables the service persons, or Health Inspector to tell at a glance if the recirculating pump is pushing an adequate amount of water to ensure optimum water turnover (filtration).

Manufacturer: GPI Brand: GPI® The Proven Choice®

Technical Specification Item Flowmeter Type Mechanical GPM Max. 20 Max. Pressure (PSI) 50 Connection Size (In.) 3/4 MNPT Max. Temp. (F) 125 Length (In.) 5-13/16 Width (In.) 5-1/4 Height (In.) 4-1/2 Housing Material Aluminum Fitting Aluminum Chamber Material PBT Polyestester Seal Material Nitrile Shaft Material Stainless Steel Flow Range @ GPM of Water 4 to 20 Flow Range 4 to 20 gpm Accuracy (%) +/- 2 Display Mechancial Register Resetable Cumulative Totalizer 9, 999 Liters in 1/10 Liter increments Master Totalizer 999, 999L Flow Material Gasoline (Alcohol Blends up to E15), Diesel Fuel (Biodiesel Blends B20) and Kerosene Flow Range (GPM) 4 to 20 Flow Range (LPM) 15 to 76 Max. Viscosity Diesel Fuel Pressure Drop - 100% Flow (PSI) 10 Pressure Drop - 50% Flow (PSI) 5 Temp. 125 Thread NPT Application Mechancial Nutating Disc Flow Meter for Gasoline (Alcohol Blends E15), Diesel Fuel (Biodiesel Blends B20) and Kerosene Agency Compliance UL Listed Manufacturers Warranty Length 2 Years For Pipe Size 3/4 Compliance & Restrictions Compliance and Restrictions This product is not intended for potable water applications (human consumption - drinking and cooking) and has not been designed to be compliant with the "Safe Drinking Water Act" requirements for low lead in potable water applications. This item is for use only in non-potable (non-human consumption) water applications. This item is restricted for conveying or dispensing water for potable use (human consumption). This listing is for each. _DELETE_

Manufacturer: Great Plains Industries Brand: GPI® The Proven Choice® Model: FM300H/R

This 1 in. chemical meter has NPT fittings, a nutating disc with electronic display, and measures in gallons.

Manufacturer: DIGITEN Brand: DIGITEN Model: BuildingMaterials

Waterproof,Heat resistance,pressure resistance,cold resistance. Easy to install Frequency: F=23 * Q (L / Min) error: 2% Flow range:0.3-10L/min Suitable for 1/4" tube Maximum Consumption current:1.5 mA(DC 5V) Working voltage range:DC3.5-12V Operating Temp:0-80C,Operating humidity:35%-90%RH Pressure range: 0-0.8MPa Storage Temperature:-25-80C Storage humidity:25%-95%RH Output Waveform:Square Wave,output pulse singal. ROHS Compliant. Cable length:15cm. Application:water heater thermostat, water purifier, boiler, water dispensers, coffee machines, smart card equipment, the boiler and so on.

Manufacturer: Dwyer Instruments, Inc. Brand: Dwyer

Offering advanced features at low cost, the Dwyer® Series MM flowmeters are ideal for a wide range of OEM and user application in medical equipment, air samplers, gas analyzers, pollution monitors, chemical injectors, cabinet purging, etc. The standard Model MMA flowmeter is suitable for both gas and liquid applications. It can be configured by the user with the parts provided to have non-removable top or bottom from mounted metering valves or no valve at all. The transparent nylon material provides high chemical resistance, low moisture absorption and is transparent to facilitate routine inspection. Using the assembly key provided, the flowmeter can be disassembled anytime for cleaning or reconfiguration. In OEM quantities, ultrasonically welded caps or interchangeable mole cores enable production of the MMA flowmeter with a low profile or flat front surface where no valve is required. The MMA is practically unbreakable, mounts easily, and is easy to read. Two 5/16" OD mounting-connection tubes permit quick push-on connection of rubber or plastic tubing. A bottom clip for "stand up" mounting is also provided. Despite its compactness, the MMA flowmeter features a 2" scales which combined with precision molding, enables highly repeatable readings to be made to within ±4% accuracy.