Calibration - Page 119

Manufacturer: Fluke Corporation Brand: Fluke Model: 419D Color: Multicolored

The Fluke 419D professional-grade laser distance meter extends your reach to 80 meters (260 feet) with even greater accuracy. It saves you time and reduces errors with enhanced features like storage for 20 complete displays and a tripod mode for stable, long-distance measurements. Measure up to 80 m (260 ft). Higher accuracy: +/-1 mm (0.04 in). View more data with backlit, three-line display. Full Pythagoras function for height measurements. Storage of 20 complete displays for quick recall. Audible keypad feedback. Minimum/Maximum function. Tripod mode for mounting meter on a tripod when measuring long distances. Stake Out feature helps you mark out defined lengths such as when constructing wooden frames. Automated End-piece Correction for measuring from an edge or corner --a built-in sensor detects the position of this bracket and automatically changes the reference point. Enhanced environmental protection:IP54-rated as dust and water spray resistant. Improved battery life of 5000 measurements with auto laser off and auto power off features. Typical measuring tolerance[1]- +/- 1.0 mm[3]. Maximum measuring tolerance[2]- +/- 2.0mm[3]. Range at Leica target plate GZM26- 80m/260'. Typical range[1]- 80m/260'. Range at unfavorable condition[4]- 60m/195'. Smallest unit displayed- 1mm/1/32". Laser class II. Laser type - 635 nm,

Manufacturer: Scientific Industries Brand: Torbal Model: TC-105 Color: grey

50g to 10mg Stainless Steel set furnished in hinged, cover box with stainless steel forceps. This weight set is adjusted to N.B.S. Class € Tolerances.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 619012

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 613520-516

All Mitutoyo gage blocks meet or exceed all known specifications. The flatness and parallelism surface finish necessary to achieve the required accuracies are the same as or better than government requirements. A certificate of inspection is furnished with all Mitutoyo gage blocks with a serial number on the case and an identification number on each block. The deviation of each block is registered. For this inspection, each gage block is measured relative to the upper level master using a gage block comparator. Grade K gage blocks are manufactured by absolute measurement using an interferometer. The gage block set and discrete gage block are supplied with a certificate of calibration. The certificate of calibration specifies the deviation from the nominal length. (Comparative measurement, however, is performed for all square gage blocks.). A certificate of accuracy, traceable to the NIST, is furnished with each Mitutoyo gage block set and individual block.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611853-516

All Mitutoyo gage blocks meet or exceed all known specifications. The flatness and parallelism surface finish necessary to achieve the required accuracies are the same as or better than government requirements. A certificate of inspection is furnished with all Mitutoyo gage blocks with a serial number on the case and an identification number on each block. The deviation of each block is registered. For this inspection, each gage block is measured relative to the upper level master using a gage block comparator. Grade K gage blocks are manufactured by absolute measurement using an interferometer. The gage block set and discrete gage block are supplied with a certificate of calibration. The certificate of calibration specifies the deviation from the nominal length. (Comparative measurement, however, is performed for all square gage blocks.). A certificate of accuracy, traceable to the NIST, is furnished with each Mitutoyo gage block set and individual block.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611629-516

All Mitutoyo gage blocks meet or exceed all known specifications. The flatness and parallelism surface finish necessary to achieve the required accuracies are the same as or better than government requirements. A certificate of inspection is furnished with all Mitutoyo gage blocks with a serial number on the case and an identification number on each block. The deviation of each block is registered. For this inspection, each gage block is measured relative to the upper level master using a gage block comparator. Grade K gage blocks are manufactured by absolute measurement using an interferometer. The gage block set and discrete gage block are supplied with a certificate of calibration. The certificate of calibration specifies the deviation from the nominal length. (Comparative measurement, however, is performed for all square gage blocks.). A certificate of accuracy, traceable to the NIST, is furnished with each Mitutoyo gage block set and individual block.

Manufacturer: Mitutoyo Brand: Mitutoyo

18" BLADE C-TYPE GRADUATIONS

Manufacturer: TTC Brand: TTC

Manufacturer: Hexagon Metrology Brand: Standard Gage

Manufacturer: Fluke Calibration Brand: Fluke Model: 2085

Fluke Calibration Micro-Baths have both. We invented the Micro-Bath. And, while many have tried to duplicate it, none of them use proprietary Fluke Calibration controllers, so none of them deliver performance like a Fluke Calibration bath. Micro-Baths can be used anywhere for any type of sensor. The 6102 weighs less than 4.5 kg (10 lb.), with the fluid. It’s lighter and smaller than most dry-wells, has a spill-proof lid, and is easier to carry than your lunch. You can take it where you need to go without carts or excessive effort. Micro-Baths can even be transported with the fluid in them.