Inside Measurement - Page 38

Manufacturer: BRENCOR Brand: BRENCOR

With foam fitted case.

Manufacturer: Starrett Brand: Starrett Model: 688M-4Z

Starrett Countersink Gauges are offered in three different angles so that the gauge sets on the angular side of the countersink, as opposed to a chamfer gauge which sets on the top edge of the chamfer. This gauge directly reads the large diameter of the countersink in 0.002" or 0.05 mm increments. A set master ring is furnished with each gauge for calibration and setting. Press the button on top of the indicator to firmly depress the gauge head into the countersink. When the gauge is removed, the indicator reading is held in place until the reset button is activated.

Manufacturer: INSIZE Brand: INSIZE Model: 3227-E3

Three points internal micrometer, 2.5-3", graduation 0002".

Manufacturer: Starrett Brand: Starrett Model: 78XTZ-1

The Starrett 78XT Series Internal Micrometer features extended travel, reducing the need to exchange anvils. The ground contact points seat the internal micrometer faster and more accurately than the spherical contacts found in other gages. The rugged and accurate internal micrometer is available individually or in economical sets from .040-12-Inch (1-300mm).

Manufacturer: Brown & Sharpe Brand: Brown & Sharpe

Manufacturer: Hexagon Metrology Brand: Brown & Sharpe Model: 06130125

The Brown & Sharpe TESA IMICRO Capa LCD inside micrometer has three-point contacts for self-centering measurement of the inside dimension (ID) of bores, and a digital single-value LCD readout that displays in inch and metric units with resolution to 0.00005” (0.001mm). An electrostatic capacitance linear encoder helps ensure repeatable, precise measurement, and Statistical Process Control (SPC) data output to transmit results to a computer or external device through an interface cable (sold separately).The micrometer’s electronic microprocessor can hold measurements at any position, convert to absolute value, set a temporary zero position, and return to a true zero reading. An automatic off function helps preserve battery life when the unit is not in use. The electronics housing has an Ingress Protection 54 (IP54) rating, which means that components are resistant to debris and to splashing water from any direction up to a volume of 10 liters per minute. The measuring faces are made of hardened steel and may be uncoated, TiN-coated, or tungsten carbide-tipped for wear resistance, depending on the model. The micrometer includes, and is powered by, a single CR2032 lithium cell battery, and comes with a plastic case for storage.Micrometers are precision measuring instruments that use a calibrated screw to measure small distances. These measurements are translated into large rotations of the screw that are then able to be read from a scale or a dial. Micrometers are typically used in manufacturing, machining, and mechanical engineering. There are three types of micrometer: outside, inside, and depth. Outside micrometers may also be called micrometer calipers, and are used to measure the length, width, or outside diameter of an object. Inside micrometers are typically used to measure interior diameter, as in a hole. Depth micrometers measure the height, or depth, of any shape that has a step, groove, or slot.Brown & Sharpe manufactures precision measuring equipment and metrology hand tools. The company, fo...

Manufacturer: Starrett Brand: Starrett Model: 124MDZ

These are the most popular inside micrometers because of their lightness, ease of use, and range. They are very useful for measuring inside diameters of cylinders and rings, measuring parallel surfaces, etc. The desired range is obtained by assembling rods and spacing collars to the micrometer head. Measuring rods are provided with a shoulder that is set accurately in the micrometer head and locked in position. When assembling rods to the A and B heads, the reading line on the micrometer head should be lined up with the marking on each rod (except for the 50-75mm rods). Rod diameters are approximately 6mm (124MA) and approximately 8.5mm (124MC). Each rod has individual length adjustment for the anvil by means of special wrenches furnished. Movement of screw: 13 and 25mm (2 Heads), number of measuring rods: 10, number of spacing collars: One 12mm, One 25mm, Two 50mm.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 339-101

The Mitutoyo 339 series Digimatic tubular LCD inside micrometer includes a set of hollow, tubular extension pipes to help provide light weight with rigidity and balance shoulderswhen measuring inside dimensions of cylinders, rings, and parallel surfaces. It has a single-value LCD readout that displays in metric units with resolution to 0.001mm, and Statistical Process Control (SPC) data output to transmit results to a computer or external device. The output jack transmits SPC results to a computer through an interface cable (sold separately).The micrometer’s electronic microprocessor can hold measurements at any position, convert to absolute value, set a temporary zero position, and return to a true zero reading. The electronics housing has an Ingress Protection 65 (IP65) rating, which means that components are resistant to penetration by dust and debris, and resistant to penetration by liquids and coolant up to the force of a low-pressure (to 30 kilonewtons/meter-squared) water jet. The measuring faces are carbide-tipped for wear resistance. The micrometer includes, and is powered by, a single SR44 silver oxide battery, and comes with a wooden case for storage.Micrometers are precision measuring instruments that use a calibrated screw to measure small distances. These measurements are translated into large rotations of the screw that are then able to be read from a scale or a dial. Micrometers are typically used in manufacturing, machining, and mechanical engineering. There are three types of micrometer: outside, inside, and depth. Outside micrometers may also be called micrometer calipers, and are used to measure the length, width, or outside diameter of an object. Inside micrometers are typically used to measure interior diameter, as in a hole. Depth micrometers measure the height, or depth, of any shape that has a step, groove, or slot.Mitutoyo manufactures precision measuring tools, metrology equipment, and systems. The company was founded in Tokyo in 1934 and formed Mitutoyo America Corporation in 1...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 339-101

The Mitutoyo 339 series Digimatic tubular LCD inside micrometer includes a set of hollow, tubular extension pipes to help provide light weight with rigidity and balance shoulderswhen measuring inside dimensions of cylinders, rings, and parallel surfaces. It has a single-value LCD readout that displays in metric units with resolution to 0.001mm, and Statistical Process Control (SPC) data output to transmit results to a computer or external device. The output jack transmits SPC results to a computer through an interface cable (sold separately).The micrometer’s electronic microprocessor can hold measurements at any position, convert to absolute value, set a temporary zero position, and return to a true zero reading. The electronics housing has an Ingress Protection 65 (IP65) rating, which means that components are resistant to penetration by dust and debris, and resistant to penetration by liquids and coolant up to the force of a low-pressure (to 30 kilonewtons/meter-squared) water jet. The measuring faces are carbide-tipped for wear resistance. The micrometer includes, and is powered by, a single SR44 silver oxide battery, and comes with a wooden case for storage.Micrometers are precision measuring instruments that use a calibrated screw to measure small distances. These measurements are translated into large rotations of the screw that are then able to be read from a scale or a dial. Micrometers are typically used in manufacturing, machining, and mechanical engineering. There are three types of micrometer: outside, inside, and depth. Outside micrometers may also be called micrometer calipers, and are used to measure the length, width, or outside diameter of an object. Inside micrometers are typically used to measure interior diameter, as in a hole. Depth micrometers measure the height, or depth, of any shape that has a step, groove, or slot.Mitutoyo manufactures precision measuring tools, metrology equipment, and systems. The company was founded in Tokyo in 1934 and formed Mitutoyo America Corporation in 1...

Manufacturer: Brown & Sharpe Brand: Brown & Sharpe