Capacitance & Resistance Meters - Page 43

Manufacturer: Megger Brand: Megger Model: 1007-331

The Megger DET24C digital clamp-on ground resistance meter measures ground resistance in multi-ground electrical installations and lightning protection systems without needing to disconnect the ground in electrical testing applications. It has a clamp with two jaws that can close around round cables and rods up to 1.45" (37 mm) in diameter and ground tapes and straps up to 1.96" (50 mm) wide to measure resistance without disconnecting the ground. The meter also provides true RMS (root mean square) measurements of current up to 35 amp to help ensure operator safety during operation. The meter has a user-selectable noise filter to allow measurements to be taken in areas with high amounts of electrical noise. The meter's internal data storage allows multiple results to be compared and tracked over time, and readings are date and time stamped. It comes with a software that provides a graphic user interface for working with the data on a computer. An alarm notifies user when user-selected minimum and maximum values for current and resistance are reached or exceeded. The hold function keeps a reading on the display, even after the meter is disconnected. In applications where the conductor is difficult to access, an auto-hold feature allows a reading to be captured without requiring the operator to press the button during measurement. The meter's liquid crystal display (LCD) is backlit to provide readability in low light. The clamp jaws have a smooth surface with no interlocking teeth to help prevent build-up of dirt and residue, which can interfere with measurements. The unit automatically turns off after five minutes of non-use to conserve battery life, and a low-battery indicator signals when the meter's batteries need to be replaced. This Megger earth test clamp-on ground resistance meter meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category IV installations up to 600V, which covers measurements at the source of the low-voltage supply, such as electricity meters an...

Manufacturer: AEMC Brand: AEMC Model: 3711

The AEMC 3711 portable clamp-on ground resistance tester measures electrical ground rod and grid resistance of installed multi-grounded systems around buildings, pads, cell towers, pools and spas, and most environments, with no leads, auxiliary rods, or spacing requirements. The meter measures down to 0.1Ω with resolution of 0.01Ω and a fast settling time of approximately one second. It provides high immunity to electrical noise around transmission towers and substations. The current measurement function provides a direct reading of leakage current flowing to ground or circulating in ground loops down to 1 milliAmp (mA) and neutral and phase currents to 30A RMS. The data hold function keeps the last reading on the display after disconnecting from the circuit under test, which allows user to record measurements in the field and analyze readings when convenient. For power management and extending battery life, the auto power-off feature shuts down the meter after a set period of time. Ground-resistance meters are used by electricians and contractors working in industrial, utility, and field servicing. The jaw design has a 1.25" opening that accommodates ground rods and larger ground conductor cables up to 1000kcmil. The ergonomic body design permits one-handed operation. The head and body of the instrument are constructed from polycarbonate material that is designed to withstand heavy outdoor usage. The tester comes with a calibration check loop and hard carrying case. Safety ratings include EN 61010 and CAT III. The double-insulated product is UL approved and CE marked. Specifications Ground resistance range Autoranging 0.01 to 1200Ω Current measurement range Autoranging 1mA to 30.00A RMS Resistance measuring frequency 2403Hz Current measuring frequency 47 to 800Hz Accuracy (% of reading) + or - 2% reading + or - 0.02Ω to 25% of reading for 600 to 1200Ω Operating temperature range -10 to 55 degrees C/14 to 131 degrees F Power source 9V battery (included) Weight 2.2lbs./...

Manufacturer: Megger Brand: Megger Model: 6410-593

The Megger DET2/2 digital ground resistance meter measures earth electrode resistance and soil resistivity to increase the safety and performance of electrical systems. The unit measures digitally and has manually-selected test current, test frequency, and filtering so that it can be used in noisy environments. The meter uses the four-terminal method to eliminate the circuit current resistance for more accurate measurements. The meter measures earth resistance from 0.01 ohms to 19.99 kilohms, with 1 microhm resolution. The alphanumeric LCD display is 35mm x 130mm and gives both test information and test results. The tester is safety rated to European Standards (IEC/EN) 61010-1. It is also Ingress Protection 54 (IP54)-rated for protection against dust and splashing water. The DET2/2 is commonly used by electricians and electrical contractors to help ensure the safety of electrical systems. Specifications Power supply Rechargeable 12V lead-acid internal battery (installed) Ground resistance range 0.01 ohms to 19.99 kilohms Ground resistance resolution 1 microhm Weight (including batteries) 5kg/11 lb. Safety standards met International Electrotechnical Commission (IEC)/European Standards (EN) 61010-1 Ingress protection (IP) standard met IP54, for protection against dust and splashing water Dimensions 245 x 344 x 158mm/9.6 x 13.5 x 6.25 inches (H x W x D)H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers, measure one property of a circuit, and multimeters measure multiple properties. Ele...

Manufacturer: Megger Brand: Megger Model: DLRO200-115

The Megger DLRO200 series digital microhmmeter measures resistance in switch and breaker contacts, bus-bar joints, and other high-current electrical systems. The meter is autoranging and digital for safety and ease of use. The internal memory stores up to 300 sets of results, which can be annotated with notes by the user. The results and notes can be downloaded to a PC or directly outputted to a printer via the RS232 port. The microhmmeter measures resistance from 0.1 microhms to 1 ohm, with test currents from 10 to 200A. The unit is safety rated to European Standard EN61010-1. The DLRO200 series is used by electricians and electrical contractors.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers, measure one property of a circuit, and multimeters measure multiple properties. Electrical test meters display information either in analog form using a needle that moves on a calibrated scale, or in digital form on an LED screen. Meters have electrical properties that are to be measured and the anticipated range of results, and should have a rating that is higher than the maximum value of the anticipated range. Meters measure electrical properties and are safety rated to measure a specific range of results. The range on the meter should be higher than the maximum anticipated value to be measured. An electrical test meter has multiple settings corresponding to potential ranges of values for the properties it can measure. A manual ranging meter requires the operator to flip through different settings until the correct range is reached. An autoranging meter cycles through range settings automatically until it reaches the correct range. Megger manufactures equipment for cable fault l...

Manufacturer: Instek Brand: GW Instek

The LCR-800 Series are high-end digital LCR meters for component/material measurements, applicable to various R&D activities and assembly lines. The large 240 x 128 dot matrix LCD display provides ample room for two measurement items and setup parameters, allowing you to grasp measurement results quickly. All test modes are able to measure supplementary factors, such as, R/Q, C/D, C/R, and L/Q. The LCR-821 also contains precise resistance measurements as a combination of absolute value and phase angle. 100 sets of measurement setup memory allow sharing a single unit among multiple testing conditions or sites. For a better viewing experience in a standard PC monitor, proprietary Windows based software is accessible via the RS-232C terminal. The handler interface is also a standard feature for LCR-826/827/829.

Manufacturer: ACCULEX Brand: Acculex

Acculex Dp-1354 Digital Panel Meter (R2-6)

Manufacturer: Hioki Brand: Hioki Model: 9216

The Hioki 9216 cable winder holds a measuring cable and is used in ground resistance testing. The winder is an accessory for the Hioki HiTester model 3151. Using a cable winder eliminates tangled cables for organized test equipment and extends equipment life. Hioki manufactures memory recorders, automatic test equipment, and electronic testing and measurement instruments. The company, founded in 1935, is headquartered in Japan and has a U.S. office in Cranbury, NJ.

Manufacturer: Drillpro Brand: DRILLPRO Model: DRILLPROTSZYmall1992

DIY Meter Tester Kit For Capacitance ESR Inductance Resistor NPN PNP Mosfet M328 Feature: Specification: Measurement Range: Resistor: 0.5¦¸ ~ 50M¦¸ Capacitor: 30pF ~ 100mF Inductance: 0.01MH ~ 10H Working voltage: can use 6FF22 9V Battery, or DC 5.5V ~ 12V via DC socket Controller: ATmega328 (has been programmed) Standby current: 0.02uA Operating current: 25mA Note: When measuring 1 uF non-polarity capacitance, attention to short-circuit capacitance between two feet and put off storage of electricity when measuring capacitance, otherwise may damage the instrument, if measuring instrument with electricity is easily to make display show CELL and can't use normally, we are not responsible for this kind of situation, what you can do is replacing the chip, it is important to note, please! Please download the install manual file from here or the topic, because it is easily damaged especially for the beginner. Package included: 1 Meter(without the battery), DIY Kits, not soldered, Atmega168 has been programmed.

Manufacturer: TOOGOO(R) Brand: TOOGOO(R)

Aluminum housing for heat dissipation, suitable for cooling plate installation, can be used in atrocious environment. Small size, high power load, standard and non-inductive winding types. High insulating capacity, good performance in vibration. Multiple connection modes, easy to install. Widely used in power supply, transducer, elevator, arena audio and high requirement equipment industry.

Manufacturer: GENERAL ELECTRIC Brand: GE

1 New General Electric 50-236412Abaa1 Time Meter (X8-11)