Electrical Testing - Page 450

Manufacturer: POMONA Brand: Pomona Model: 5309A-POMONA

POMONA 5309A TEST LEAD SET

Manufacturer: Nu-Calgon Brand: Nu Calgon Color: Multicolored

Humiditreat Scale Reducing Inline Filter for Whole House Humidifiers.  Description:Humidi-Treat is designed for humidifiers using up to 25 gallons per day, and will inhibit scale for one season. Install Humidi-Treat on the water line that supplies water directly to the humidifier.Application:Clean pad or install new pad before installing Humidi-Treat.For best results humidifier should have a daily dump of water from the sump to diminish • scale forming minerals.Install a new Humidi-Treat before each heating season.Humidi-Treat works best when installed on a cold water line.Humidi-Treat has internal 1/4" push-on fittings Installation Steps:* Shut off water.* Disconnect existing filter or cut water line where filter is to be installed*  "Quick Connect" fittings * Insure proper direction of water flow and connect inlet and outlet.* Carefully turn on the water and check for leaks* Check the filter after approximately 8 hours for slight leaks not visible during initial installationFilter Length - 5-1/4"

Manufacturer: APR Supply Co. Brand: Nu Calgon Model: 4168-08 Color: Multicolored

Directions of Use: 1. Turn off equipment and access evaporator coil. 2. If the coil is heavily soiled with lint, dirt, etc., use a brush to remove as much as possible prior to cleaning. 3. When using Evap Pow'r-C, prepare a cleaning solution in one of the quality Nu-Calgon sprayers, mixing one part of Evap Pow'r-C with three parts of water. 4. Be sure nearby registers are closed. Although the blower was turned off, natural air currents could pick up and entrain droplets of cleaning solution and this should be controlled. 5. Spray cleaning solution onto coils, being sure to lightly coat all surfaces. 6. Rinsing is not required, particularly where there is sufficient humidity being condensed from the ambient air to provide a flushing or rinsing action. Return system to service. 7. If rinsing is done, take the opportunity to treat coil with Cal-Shield, a Teflon surface protectant (4148-08).

Manufacturer: DROK Brand: DROK

Technical parameters: Input pulse signal: open NPN / PNP collector contact switches, non-contact switch, limit switch, level pulse and so on. Input signal voltage: High level H = 4 ~ 30V, low level L = 0 ~ 0.6V, falling edge trigger Measuring range: 0 to 9999 cumulative count Count input frequency: less than 2000Hz Display: 0.56"high brightness LED Power supply: DC 5V ± 10%; ＜ 80mA Working temperature: -10 ~ 60 °c (relative humidity of 80% or less) Dimensions: 79 x 43 x 25mm Mounting Hole Size: 75 x 39.5mm Using: The magnet close to the magnetic proximity switch about 0.5-1 cm, then the magnet away from the magnetic proximity switch for a certain distance (typically 3-5 cm or more). Then start counting. Note: 1, the count signal and reset signal input switching should closer to the counter terminal. 2, to avoid unnecessary interference, if necessary, please use shielded cable, shield connected to the count terminal "+". 3, recommended to use magnetic switch Package includes: 1x Digital counter 1x MagSwitch 1x Magnet

Manufacturer: OneTrip Parts® Brand: OneTrip Parts® Color: Multicolored

This limit control is the direct replacement for many Rheem, Ruud, and Weatherking furnace models. These switches are located above burners and shut the furnace down in the event of flame rollout. This part is covered by the exclusive OneTrip Parts® two year limited replacement policy. If this part fails within two years from date of purchase, return the defective part and a copy of the original invoice to the place of purchase for replacement. Contact the authorized OneTrip Parts® dealer that you purchased the part from for details. Original equipment manufacturer's brand name(s) and part numbers are used for identification purposes only. This item is supplied by OneTrip Parts® and meets or exceeds original equipment specifications.

Manufacturer: Reed Brand: REED Instruments Model: TL-88-A15

Safety test leads with alligator clips. Slide-on style for test probes. Jaws open to 8mm.

Manufacturer: Greenlee Brand: Greenlee Model: GT-16 Color: Greens

The Greenlee GT-16 Non-Contact Voltage Detector is adjustable to safely detect power and low voltage. Safely detects AC voltage without touching the bare conductor. Adjustable for use on power wiring plus lighting, thermostats and other low voltage circuits. Use to detect voltage in outlets, lighting fixtures, wires and cables. Finds breaks in wires. Identifies hot and neutral conductors. Low battery indication. Includes: (1) 1.5-Volt AAA battery. Lifetime Limited Warranty.Dimensions: 8.7″ x 12.75″ x 9.5″.

Manufacturer: Southwire Brand: Southwire Model: 58290840

Southwire 10030S manual ranging digital multimeter cat III 300V UL 7 functions with 20 ranges. Backlit digital display. Special ranges for testing aaa, aa, c, D and 9V batteries

Manufacturer: RioRand Brand: RioRand Model: RRAPLFMA

Features: Cutting size:37.5 x 21mm Dimensions: 40.5 x 24 x 17.5mm Range: DC 0-300A Power Supply: DC 6-24V Display: Four 0.36 " LED digital tube Display Color: Green Refresh rate: about 300mS / times Input impedance: about 100Kohm Accuracy: 0.5%(+/- 5 digit), when measure 0-10A, accuracy of about 0.1 Operating temperature: -40°c ~ 85°c When measure 105.65A, LED display 105.6 When measure 10.51A, LED display 10.51 Wiring: POWER: Power supply DC 6-24V, Red: battry Power+, Black: battry Power - INPUT: Measure Current DC 0 ~ 300A, Green: Shunt+ , Black: Shunt- Package Included: 1x 300A Digital Ammeter 1x 300A/75mV Shunt

Manufacturer: Bcn Auto part&accessories Brand: Bcn

Description: Volt:12V 100% Brand New Body color: Black Dial color: Silver Numbers color: Blue Pointer color: Red Lights color: Turquoise Tacho reads from 0 - 8,000 RPM. Works on 4,6,and 8 cylinder engines. Volt,Oil Temperature,Oil Pressure & Boost gauges also available in range. Package Includes: 1 X Tacho Gauge 1 X Hose 2 X Screws 1 X English Instructions