|
|
-
3.8 of 5.0 with 25 Reviews
SALE PRICE: $137.97 1% OFF
Manufacturer: HHIP
Brand: HHIP
Model: 4400-1406
Manufacturer: HHIP
Brand: HHIP
Model: 4400-1406
1.4 - 6" Dial Bore Gage ~ .0005" Graduation ~ 6" probe depth. ~ 17 anvils included. ~ for close tolerance measurements of holes, taper and roundness. ~ Gages are supplied with an AGD Group II dial indicator. ~ Easy setting with micrometers or ring gages. ~ Self centering. ~ Fitted case with anvils index.
-
3.8 of 5.0 with 14 Reviews
SALE PRICE: $144.00 1% OFF
Manufacturer: Starrett
Brand: Starrett
Model: 82A6
Manufacturer: Starrett
Brand: Starrett
Model: 82A6
All probes are furnished with an actuating rod.
-
3.8 of 5.0 with 19 Reviews
SALE PRICE: $155.00 1% OFF
Manufacturer: Flexbar
Brand: Flexbar
Manufacturer: Flexbar
Brand: Flexbar
|
Flexbar Sensing-Saf-Start. The inexpensive Solution to OSHA. Anti-automatic Restart Protection Without the High Cost of Magnetic Motor Starters This is a mandatory OSHA safety requirement. With the Sensing-Saf-Start correctly installed on existing equipment, it will Provide Protection against unexpected start-up, motion, and motor burn-out in the following manner: Voltage drop or power interruption Protection. in the event equipment, while being operated (switch in the "On" Position), should stop due to loss or drop of Electrical power due to Power Failure from any cause, the Sensing-Saf-Start will automatically Disconnect and shut off power to the equipment, so that upon restoration of power, the equipment will Not start up even though the power switch to the equipment is in the "On" Position. in order to restore power to the equipment, the equipment switch must be turned "off" first, and then the ReSet button on the Sensing-Saf-Start depressed. in the event the equipment is inadvertantly unplugged and then Plugged Back into the power source while the equipment switch is in the "On" Position, the equipment will Not restart until the Reset button on the Sensing-Saf-Start is depressed. The Sensing-Saf-Start is intended for installation on equipment which operates on 120-volts or 240-volts A.C. and which is connected to the source of Electric power by means of a 3-Wire Flexible power Cord. The following Standards apply to Machines Driven by 120 volt and 240 volt motors: OSHA (US Occupational Safety and Health Administration 29 DFR #1910.213 (b) (3)*) NFPA (Electrical Standard for industrial Machinery, 1997 Edition, Section 8, Protection) Model No. 17024., 20" Cord on equipment switch End. 8' Cord on power End (No Plug). You must instAll matching Plugs. Rated 200 to 240-volt A.C., 15-amp (Single phase) 2 H.P. maximum, 50/60 cycle.
-
3.8 of 5.0 with 40 Reviews
SALE PRICE: $156.00
Manufacturer: Accusize Co. Ltd.
Brand: Accusize Industrial Tools
Model: 3011-5051
Manufacturer: Accusize Co. Ltd.
Brand: Accusize Industrial Tools
Model: 3011-5051
-
3.8 of 5.0 with 28 Reviews
SALE PRICE: $159.00 1% OFF
Manufacturer: Flexbar
Brand: Flexbar
Manufacturer: Flexbar
Brand: Flexbar
|
Flexbar Sensing-Saf-Start. The inexpensive Solution to OSHA. Anti-automatic Restart Protection Without the High Cost of Magnetic Motor Starters This is a mandatory OSHA safety requirement. With the Sensing-Saf-Start corRectly instAlled on existing equipment, it will Provide Protection against unexpected start-up, motion, and motor burn-out in the following manner: Voltage drop or power interruption Protection. in the event equipment, while being operated (switch in the "On" Position), should stop due to loss or drop of Electrical power due to Power Failure from any cause, the Sensing-Saf-Start will automatically Disconnect and shut off power to the equipment, so that upon restoration of power, the equipment will not start up even though the power switch to the equipment is in the "On" Position. in order to restore power to the equipment, the equipment switch must be turned "off" first, and then the ReSet button on the Sensing-Saf-Start depressed. in the event the equipment is inadvertantly unplugged and then Plugged Back into the power source while the equipment switch is in the "On" Position, the equipment will Not restart until the Reset button on the Sensing-Saf-Start is depressed. The Sensing-Saf-Start is intended for installation on equipment which operates on 120-volts or 240-volts A.C. and which is connected to the source of Electric power by means of a 3-Wire Flexible power Cord. The following Standards apply to Machines Driven by 120 volt and 240 volt motors: OSHA (US Occupational Safety and Health Administration 29 DFR #1910.213 (b) (3)*) NFPA (Electrical Standard for industrial Machinery, 1997 Edition, Section 8, Protection) Model No. 17025., Short Extension Cord Style. 14" Cord on male Plug End, 12" Cord on female receptacle End. Rated 120 volts, A.C., 15-amp, 3/4 HP motor maximum, 50/60 cycle.
-
3.8 of 5.0 with 49 Reviews
SALE PRICE: $160.99 1% OFF
Manufacturer: Freud Tools
Brand: Freud Tools
Manufacturer: Freud Tools
Brand: Freud Tools
Create a uniform chamfer on the edge of any work piece to add character, while retaining crisp geometric linesChamfer Size easily adjusts by changing the height of the bit.Cut all composition materials, plywoods, hardwoods, and softwoodUse on hand-held and table mounted portable routers2 Flute design for efficient cutting and dust removalCutter Diameter: 2-1/2 inch Carbide Height: 1 inch Overall Length: 2-7/8 inch Angle: 45?Bearing Diameter: 1/2 inch Shank Diameter: 1/2 inch.
-
3.8 of 5.0 with 39 Reviews
SALE PRICE: $170.37 1% OFF
Manufacturer: ABS Import Tools, Inc.
Brand: HHIP
Model: 4040-0017
Manufacturer: ABS Import Tools, Inc.
Brand: HHIP
Model: 4040-0017
HHIP 0001 inch graduation dial bore set features for closer tolerance measurements of holes, taper and roundness. Self centering. Gages are supplied with AGD Group II dial indicator. Easy setting with micrometers or ring gages. Fitted case with anvils Index.
-
3.8 of 5.0 with 3 Reviews
SALE PRICE: $183.66 1% OFF
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 139-002
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 139-002
|
The Mitutoyo 139 series tubular vernier inside micrometer includes a set of extension pipes with anvils for a diversified range of measurement measuring inside dimensions (ID) of cylinders, rings, and parallel surfaces. It has a vernier scale in inch units for taking precise ID measurements to 0.001â€, and a satin chrome rust- and glare-resistant finish. The micrometer head has a travel of 1†per revolution that helps provide quick positioning. The hollow, tubular extension pipes help provide light weight with rigidity. A locking clamp helps hold measurements in place. The micrometer and accessories come with a fitted case for storage.Micrometers are precision measuring instruments that use a calibrated screw to measure small distances. These measurements are translated into large rotations of the screw that are then able to be read from a scale or a dial. Micrometers are typically used in manufacturing, machining, and mechanical engineering. There are three types of micrometer: outside, inside, and depth. Outside micrometers may also be called micrometer calipers, and are used to measure the length, width, or outside diameter of an object. Inside micrometers are typically used to measure interior diameter, as in a hole. Depth micrometers measure the height, or depth, of any shape that has a step, groove, or slot.Mitutoyo manufactures precision measuring tools, metrology equipment, and systems. The company was founded in Tokyo in 1934 and formed Mitutoyo America Corporation in 1963, which is headquartered in Aurora, IL.
-
3.8 of 5.0 with 40 Reviews
SALE PRICE: $216.77 11% OFF
Manufacturer: Starrett
Brand: Starrett
Model: 3089Z-131-715J
Manufacturer: Starrett
Brand: Starrett
Model: 3089Z-131-715J
The Starrett 3089 Series Dial Bore Gage offers precision, a full compliment of features and excellent value.
-
3.8 of 5.0 with 16 Reviews
SALE PRICE: $234.89
Manufacturer: ASIMETO
Brand: ASIMETO
Model: 483-21-1
Manufacturer: ASIMETO
Brand: ASIMETO
Model: 483-21-1
Dial Bore Gages, Dial Bore Gage Sets, ASIMETO
|
|