Insulation Resistance Meters - Page 17

Manufacturer: CEM Brand: CEM

1mA test current for MegOhm range at rated voltage 200mA short current for continuity range

Manufacturer: Megger Brand: Megger Model: 6111-503

The Megger 6111 series two-piece duplex test lead set with spring-loaded duplex hand spikes is for use with Megger DLRO10HD, DLRO10, DLRO10X, and BT51 digital microhmmeters. These duplex test leads measure both current and resistance when taking four-wire resistance measurements, which are more accurate than two-wire resistance measurements and allow low resistance values to be detected. The spring-loaded hand spikes compress to make contact with a conductor. Light-emitting diodes (LEDs) on one probe confirm connection and the presence of live current when used with the Megger DLRO10 microhmmeter, and can indicate test pass/fail when used with the Megger DLRO10X microhmmeter. There is 0.23" (6 mm) between the current and potential probe tips on the duplex hand spikes.A test probe, test lead, test prod, or scope probe transmits an electrical signal to a testing device for display and analysis. Designs range from simple test leads with probe-style or clamp-on tips to more complex oscilloscope probes and current detectors. Some test probes, such as basic test leads, have wires with tips for connecting to test equipment. Other test probes, such as voltage detectors, are built into the meter. Depending on what is to be tested, the probe might either be passive or have active parts that require external power to operate. Some probes require contact for testing, while some are capable of taking measurements from a distance. Some also have finger barriers, insulation, or other features to help protect the operator's hand from electrical shock and burns. Test probes are rated according to the amount of voltage, current, temperature, or other input they can measure. When choosing a test probe, the maximum amount of input that the probe can measure should match or exceed both the maximum amount that can be tested by the test equipment, as well as that of the property expected to be present in the application.Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integri...

Manufacturer: Amprobe Brand: Amprobe Model: AMC-3

The Amprobe AMC-3 hand cranked insulation tester is an analog meter to measure insulation resistance on wires, cables, transformers, and electrical motors. The unit measures insulation resistance from 0 to 1,000 Megaohms using a 1,000V direct current (DC) test voltage. It also has a low-resistance range that measures from 0 to 200 ohms with a 300mV DC test voltage. The test voltage is produced by a hand-cranked constant voltage generator, so the unit never needs batteries. A guard terminal prevents surface leakage from affecting the instrument's readings. The AMC-3 is designed for use by electricians and electrical contractors. Specifications Power supply Hand-cranked constant voltage generator Insulation resistance range 0 to 100 Megaohms, 0 to 200 ohms DC test voltage 300mV or 1,000V Weight (including batteries) 2.5 lb./1.13kg Dimensions 7 x 4 x 3.6 inches/177.8 x 101.6 x 92.1mm (H x W x D)H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers, measure one property of a circuit, and multimeters measure multiple properties. Electrical test meters display information either in analog form using a needle that moves on a calibrated scale, or in digital form using digits or a graphic representation on an LED screen. Meters have electrical properties that are to be measured and the anticipated range of results, and should have a rating that is higher than the maximum value of the anticipated range. An electrical test meter has multiple settings corresponding to potential ranges of values for t...

Manufacturer: Megger Brand: Megger Model: MIT320-EN

The Megger MIT300 series insulation resistance tester measures insulation resistance, voltage, and continuity in electrical installations, building maintenance, and electrical testing. The average-sensing meter provides accurate readings when measuring linear loads, where the current or voltage has a sinusoidal waveform. The dual LCD screen indicates test results either digitally or with an analog arc function to replicate the response of analog meters. The tester measures insulation resistance from 0 to 1,000 megohms, voltage from 0 to 600V, and continuity from 0.01 to 100 ohms. The unit has a test inhibit function that prevents testing on circuits carrying over 50V. The tester is safety rated to European Standard EN61010-1, Category III, 600V. The unit is also Ingress Protection 54 (IP54)-rated for protection against dust and splashing water. The unit has a rubberized outer case for protection against bumps and short drops. The Megger MIT300 series is commonly used by electricians and electrical contractors.Specifications Continuity testing range 0.01 to 100 Ohms Insulation resistance range 0 to 1,000 megohms Voltage testing range 0 to 600V AC/DC Voltage test inhibit level 50V Power supply 8 AA alkaline or rechargeable batteries Weight 980g Safety standard met International Electrotechnical Commission (IEC)/European Standards (EN) 61010-1 Cat III 600V Mechanical standard met IP54, for protection from dust and splashing water Dimensions 203 x 148 x 78mm / 8 x 5.7 x 3.2 inchesH is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function me...

Manufacturer: Megger Brand: Megger Model: 242002-7

The Megger 242002 series duplex test lead with fixed-point duplex hand spikes is for use with Megger DLRO10HD, DLRO10, DLRO10X, 247000, 247001, 247002, 247100, 247101, and BT51 digital low-resistance ohmmeters. This duplex test lead measures both current and resistance when taking four-wire resistance measurements, which are more accurate than two-wire resistance measurements and allow low resistance values to be detected. The lead has a maximum test current input of 10 amp. There is 0.35" (9 mm) between the current and potential probe tips on the duplex hand spikes.A test probe, test lead, test prod, or scope probe transmits an electrical signal to a testing device for display and analysis. Designs range from simple test leads with probe-style or clamp-on tips to more complex oscilloscope probes and current detectors. Some test probes, such as basic test leads, have wires with tips for connecting to test equipment. Other test probes, such as voltage detectors, are built into the meter. Depending on what is to be tested, the probe might either be passive or have active parts that require external power to operate. Some probes require contact for testing, while some are capable of taking measurements from a distance. Some also have finger barriers, insulation, or other features to help protect the operator's hand from electrical shock and burns. Test probes are rated according to the amount of voltage, current, temperature, or other input they can measure. When choosing a test probe, the maximum amount of input that the probe can measure should match or exceed both the maximum amount that can be tested by the test equipment, as well as that of the property expected to be present in the application.Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integrity, and power quality testing under multiple brand names, among them Megger, Biddle, States, and AVO. The company, founded in 1889, is headquartered in Dover, England, and meets International Organization ...

Manufacturer: Megger Brand: Megger Model: 210415

The Megger 210400 series megohmmeter is an analog meter that measures insulation resistance to help reduce shock hazards and downtime on electrical systems that include wires, cables, transformers, and electrical motors. A manual range-selection knob allows the operator to choose the measuring range and the continuously variable test voltage provides highly sensitive insulation resistance readings. The unit tests insulation resistance with low- or high-voltage test voltages. The shielded high-voltage output cable is permanently attached to the unit to avoid damage to the unit. The unit includes circuit breaker protection and redundant grounding connections for increased safety. The 210400 series is commonly used by electricians and electrical contractors. Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers, measure one property of a circuit, and multimeters measure multiple properties. Electrical test meters display information either in analog form using a needle that moves on a calibrated scale, or in digital form on an LED screen. Meters have electrical properties that are to be measured and the anticipated range of results, and should have a rating that is higher than the maximum value of the anticipated range. Meters measure electrical properties and are safety rated to measure a specific range of results. The range on the meter should be higher than the maximum anticipated value to be measured. An electrical test meter has multiple settings corresponding to potential ranges of values for the properties it can measure. A manual ranging meter requires the operator to flip through different settings until the correct range is reached. An autoranging meter cycles through ...

Manufacturer: Ideal Industries, Inc Brand: Ideal Model: TL-797RP

The Ideal TL-797RP is a remote probe designed for use with the Ideal 61-797 digital insulation meter

Manufacturer: UNI-T Brand: UNI-T

This UNI-T UT501 insulation tester measures resistance, insulation resistance and AC/DC voltage. UNI-T UT501 Insulation Tester Features •Functions: ◦insulation resistance ◦resistance ◦DC voltage ◦AC voltage •Auto ranging •Alarm light display and buzzer •Low battery indication UNI-T UT501 Insulation Tester Package •Megaohmmeter UNI-T UT501 (1 pc.) •Test lead (1 pc.) •Test probe (1 pc.) •Alligator clip (1 pc.) •Carry bag (1 pc.) •Strap (1 pc.) •1.5 V battery (LR14) (6 pcs.) •User manual (1 pc.)

Manufacturer: Duoyi Brand: Yi Duo Model: X1IN10090

Features: Six test voltages cover 100V, 250V, 500V, 1000V, 2500V, 5000V for flexible application Measure insulation resistance to 200G¦¸ with 0.01m¦¸ resolution Data hold, auto range, auto power off, LCD background light Complete with test leads, heavy duty carry case Package includes: 1 * DY5106A Insulation Resistance Tester 1 * Accessory Kit (Insulation test leads) 1 * Carry case

Manufacturer: FLUKE CORP. Brand: FLUKE CORP.

Analog Megohmmeter, Insulation Tester 1000 Meg