Capacitance & Resistance Meters - Page 39

Manufacturer: waikei Brand: waikei

Specifications If there is something wrong with LED light group, you can change it or replace the bad LED beads. Model No: SID-GJ2C Input Voltage: 85-265V International General Output Voltage: 0-300V High Brightness No Disassemble More Accurate. Double Isolated Safe Protection. Voltage and Current Intelligent Adjustment. Voltage Range: 0-300V (slow boost safety design of soft start) Testing Skills Plug in power, it can be used after 3to 5 seconds. The soft start mode make the backlight getting brighter slowly. No burn out, If you can't make sure the "+"and "-", Don't connect the probes to the LED which be tested for a long time. Open Ciruit Protection : Don't touch the output terminal of probes for a long time .It's safe for touch the probes in short time periods. Double Isolate Design makes our tester safety with high strength and flame retardancy materials. Single LED light bar backlight testing Make sure the anode and the acthode. Connect the probes on the anode and the cathode. Light up the Single LED light Bar Backlight. Light up the Double LED Light Bar Backlight. Packing Includes 1 x TD 0-300V Output Voltage All Size LED LCD TV Backlight Tester 2 x Table pen

Manufacturer: Newport Brand: Newport

Newport Digital Panel Volt Meter 2584 Bl (5415)

Manufacturer: Signstek Brand: Signstek

Using 100kHz to remove the impedance 1/(2*pi*F*C), the impedance will become small, and then we can measure the true series resistor value. A bad E-capacitor have larger ESR and create large ripple rather than filtering noise. Normally, a big capacitor is larger than 3 ohm. Therefore, we can measure the capacitor is bad, damaged or in good condition by using this theory. Because our ESR meter only applies less than 15mV DC or peak to peak on a good capacitor, as a result we can use it as in circuit test. Because this low testing voltage, it cannot turn on the semiconductor inside a circuit under testing. During repairing TV, LCD, Audio board, etc. we can in circuit testing the capacitor is good or not. Advantage of V2: 1) Change square wave to sine wave 100 KHz, reduce square wave's high frequency component, and affect the reading passing the test leads and capacitor. 2)Higher Resolution up to 0.001 ohm. 3)128X64 dot matrix LCD, with larger value display and information 4)Embedded 25V capacitor table at LCD, auto display the capacitor is good or bad reference to common 25V electrolytic capacitor. 5)New plastic case, curve design for hand carrying. New stand for 60 degree stand on desk. 6)Use 2X AA battery, more convenience and longer battery life than 9V battery. 7)Support external USB power, using standard micro-USB port. Specification: 1)Accuracy: Up to 1% (detail on above table) 2) High Resolution: 4 digit, or 0.001Ohm @ 1 Ohm range 3)Measuring voltage: 80 Hours Package 1x MESR-100 V2 2 x test clips

Manufacturer: RioRand Brand: RioRand Model: RRQSSSSSSSSSSS

Performance indicators: Measurement accuracy: 1% Capacitance Measuring Range: 0.01pF-10uF Minimum resolution: 0.01pF Inductance Range: 0.001uH-100mH Minimum resolution: 0.001uH Large inductance measurement range: 0.001mH-100H Minimum resolution: 0.001mH Large capacitance measurement range: 1uF-100mF Minimum resolution: 0.01uF Test Frequency: capacitors, inductors gear is about 500kHz, large inductance is about 500Hz, it can display current test frequency value Display : 4 Digits 1602 LCD Power supply: 4 pcs 5 # battery, miniUSB interface or 5V power supply Features: Handheld portable, low-power Accuracy, high resolution, capable of measuring inductance of less than 1pF and capacitor of less than 1uH Powered ways: Mini USB, DC 5V power adapter, 4 5 # battery. Using mini USB connection or DV 5V supply more energy efficient. 5 minutes intelligent auto power-off function Tips: If the inductive resistance over 100 ohms or more, then there will be some test error for the instrument Package included: 1x LC200A handheld inductance capacitance meter 1x Mini USB cable 1x Power supply 1x SMD Test Clips

Manufacturer: Signstek Brand: Signstek

Feature: Handheld LCD display capacitance meter Measure range from 0.1 pF to 20000 u F Measuring range:20mF/2000μF/200μF/20μF/2μF/200nF/20nF/2000pF/200pF Compact structure Easy operation Convenient to carry It is the perfect electrical measuring tool Sample rate:2 ~ 3 times per second Zero adjustment:hand movement Suitable for digital analysis ,Choose capacitance,measure the unknown capacitance , Matching capacitance, Measurement cable and capacitance, etc. Specifications: 1. Range: Best Accuracy 2. Capacitance: 200pf/2000pf/20nF/200nF/2μF/20μF/20 0μF ±(0.5%+20), 2000μF ±(2%+10), 20mf ±(4%+20) 3. Power: 9V Battery 4. Product Color: Random Delivery 5. The max Display: 1999 6. Work Environment: 0℃-40℃ 7. Storage Environment: -10℃-50℃ 8. Product Dimensions: (5.63 x 2.95 x 1.26)"/ (14.3 x 7.5 x 3.2)cm (L x W x H) 9. Product Net Weight: 8.36oz / 237g Package: 1 x Tester 1 x Probe 1 x Manual

Manufacturer: Signstek Brand: Signstek

Description of Signstek M4070: Signstek M4070 LCR meter is auto-ranging component tester, which can drive up to 500 KHz. Suitable for small value capacitor and inductor measurement, provides very stable and high resolution measurement up to 5 digits. Meter can measure 0.00pF to 100.00mF capacitance, 0.000uH to 100.00H and 0.00Ω to 10.000MΩ. M This meter is using two technique measurement, LC oscillation and RC oscillation. LC is much suitable for small value measurement and RC for high value capacitance. Feature: Fully auto-ranging designed High resolution, up to 5 digit display, most finest resolution: 0.01pF, 0.001uH, 0.01R High stability and measurement range for L/ C/ R USB charging with rechargeable battery inside Large LCD display with backlight USB PC program, can take record and pass and fail component sorting function. Specification: Warranty: 6 months warranty. 30 days free return and money back guarantee. 24 customer service response. LCR Testing Parameter: Main Parameter: L / C / R Testing frequency: C: 10 to 500Khz & L: 10 to 360Khz Testing Method: Auto select LC and RC Oscillation Calibration: Power on auto calibrate with internal reference capacitor Testing voltage:~1.5Vrms Best Tolerance: L: 1% +1 Digit C: 1% +1 Digit R: 0.5% +1 Digit LCD update or Testing time (* vary on component value):(e.g. 100mF Capacitor

Manufacturer: FLIR Systems Brand: Extech Model: LCR203

electronic-components

Manufacturer: Fluke Corporation Brand: Fluke Model: GEO CABLE-REEL 25M

The Fluke GEO reel with 25m/82ft. of red wire cable is used to connect Fluke 1621, 1623, and 1625 testers to stakes for measuring earth ground resistance. The cable ends terminate with a banana plug and a connector to attach the earth ground tester to the Fluke earth stakes. The red cable reel has a hand crank on top of the reel for winding the cable back on the spool after use. The plug and the connector ends of the cable can be inserted into special slots on the reel to avoid unspooling of the wire. Fluke Corporation manufactures electrical testing tools and software for industrial and commercial applications. The company, founded in 1948, is headquartered in Everett, WA.

Manufacturer: VICTOR Brand: Victor Model: VC60B+

Introduction:The whole instrument is stylish and superior grade in appearance and highly stable in performance. It can be operated by both hands through using a shoulder strap. It is most suitable for the needs of insulation resistance check, such as electric, cable, electrical and mechanical equipment, telecommunication equipment and electrical facilities.Specification:Model: VC60B?Measuring Voltage: 50V±10% 500V±10% 1000V±10%Insulation Range: 0.1M?~20 M? 0.1M?~50 M? 0.1M?~100 M? 20M?~500 M? 50M?~1000 M? 100M?~2000 M?Accuracy: ±(4%+2)Current of Short Circuit: 1.8mA 1.8mA 1.6mAMedian Resistance: 2M? 2M? 5M?Terminal Position: L & EVoltage Test(AC750V) Accuracy: ±(1.0% of reading + 6 digits)Input Impendance: 1M?Frequency Response: (50~200) HzTerminal Position: ACV & GAlarm Function Red indicator light is illuminatedLow Battery Indication: YesOver Load Indication: YesUnit Symbol Display: YesAuto Power Off: YesMax. Display: 1999Over Range Display: "1"Operating Temperature: 0?~40?Relative Humidity: 30%RH~85%RHDimension: 105×164×70mmWeight: 900gPower: 9V,6 x AA/1.5V battery (Not Included)Package Include:1 x Digital Insulation Tester1 x 10A Test Leads2 x Alligator Clip1 x Shoulder Strap1 x User Manual (only electronic version available, which can be obtained from the above link)Note?The batteries are not included in the package due to Aviation Security Check. You need to perchase suitable batteries locally. Sorry for any inconvenience caused.

Manufacturer: Megger Brand: Megger Model: 6280-375

The Megger 6280-375 12V auxiliary socket charger is an AC/DC adapter that charges batteries and powers a Megger DET4TR2 or DET4TCR2 ground resistance tester (sold separately). The 12V adapter powers the ground resistance tester's internal battery charge to help ensure it has sufficient power to operate properly. The 6280-375 is an accessory for use with Megger DET4TR2 and DET4TCR2 ground resistance testers.Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integrity, and power quality testing under multiple brand names, among them Megger, Biddle, States, and AVO. The company, founded in 1889, is headquartered in Dover, England, and meets International Organization for Standardization (ISO) 9001:2008 standards.