Pressure & Vacuum - Page 132

Manufacturer: Dwyer Instruments Brand: Dwyer Model: 4000-5KPA

The Dwyer Capsuhelic series 4000 differential pressure gauge with an aluminum case has a circular 4" (100 mm) dial, and four female 1/4" NPT rate connections, and measures pressure with single scale in inch water column (WC), mm WC, cm WC, psid, or kPa with a display accuracy of + or - 3 or 4%. The die-cast aluminum case with impregnated hard coating is for measuring air and compatible gases and oil-based liquids. The circular dial is 4" in diameter and measures pressure with a single scale in inch water column (WC), mm WC, cm WC, psid, or kPa. The pressure being measured is held within a capsule in the gauge, which permits the use of the gauge on system pressures of up to 500 psig, even with differentials less than 0.1 in WC. The gauge accuracy is + or - 3% of full scale at 70 degrees F (21.1 degrees C) with + or - 4% of full scale on some models. The pressure limits are -20" Hg. to 500 psig. The temperature limit is 20 to 200 degrees F (-6.67 to 93.3 degrees C). Four female connections with 1/4" NPT (National Pipe Thread) rate provide for vertical mounting of the gauge. The connections are paired with one high and low pressure pair of taps on top for air and gas and one high and low pressure pair on bottom for liquids. This gauge is suitable as a readout device when measuring flowing fluids, pressure drop across filters, liquid levels in storage tanks, and other applications involving pressure, vacuum, or differential pressure. The gauge comes with two 1/4" NPT plugs for duplicate pressure taps, four flush mounting adapters with screws, and four surface mounting screws.Pressure gauges are instruments used to measure the pressure of a gas or liquid inside a vessel and, often, to help ensure the optimal amount of pressure for a given application. Pressure gauges can range from everyday instruments, such as those used to measure the air pressure in a car or bicycle tire, to highly accurate gauges used in mechanical and industrial processing. Most often, pressure gauges measure pressure relative to another referenc...

Manufacturer: Dwyer Instruments Brand: Dwyer Model: IS626-16-GH-P1-E1-S1

The Dwyer Series IS626 Intrinsically Safe Pressure Transmitters convert pressure into a standard 4-20 mA output signal. The Series IS626 can be used to accurately measure compatible gases and liquids compatible with its 316/316L Stainless Steel wetted parts. Series IS626 full scale accuracy is 0.25%. Designed for industrial environments with a NEMA 4X (IP66) housing, this transmitter resists most effects of shock and vibration. Models are available with a 3' cable or M-12 4 pin connection. The IS626 is UL listed for use in Hazardous (Classified) Locations. The protection method is by Intrinsic Safety,"ia". It was investigated by UL under UL Standard 913 Sixth Edition and CSA Standard No. 157-92.

Manufacturer: Fluke Brand: Fluke Model: FLUKE-88-5/A KIT Color: Automotive Multimeter Combo Kit

The Fluke 88 V/A KIT Automotive Multimeter Combo Kit comes with the 88 Series V automotive multimeter, silicone test leads, alligator clips, test probes, inductive RPM pick-up probe, ToolPak magnetic meter hanging kit, temperature probe, two automotive backprobe pins, insulation piercing probe, and a durable carrying case. The digital multimeter (also known as a multitester) is designed for use in high energy environments such as those found on hybrid vehicles and measures AC/DC voltage up to 1,000V, AC/DC current to 10 amp (20 amp for a maximum of 30 seconds), frequency to 200 kilohertz, resistance to 50 megaohms, capacitance to 9,999 microfarads, temperature from -200 to +1090 degrees C (-328 to +1994 degrees F) and includes continuity and diode tests. The 6,000-count resolution, 3-3/4 digit digital display has a bright white backlight for readability in low-light conditions with a 4-1/2 digit mode for precise measurements and displays an analog bar graph which is useful for fast-changing or unstable signals. The meter performs millisecond pulse width measurements for fuel injectors and has Min./Max.-Average recording as well as a Min./Max. Alert to automatically capture variations. A duty cycle indicates the percentage of time a signal is above or below the trigger level during one cycle and a peak capture function detects intermittent problems and transients as low as 250 microseconds. The meter has both manual- and auto-ranging modes for user flexibility, and an auto-hold function to capture stable readings. The relative mode removes test lead resistance from low ohms measurements. This meter is safety rated for Category III up to 1000V and Category IV up to 600V and can withstand hazardous volt spikes in excess of 8,000V to reduce risks of spikes and surges caused by load switching and faults on industrial circuits. It uses a 9V battery (installed) that has a battery life of approximately 400 hours without backlight and has a selectable sleep mode to maximize battery life. The meter measures 20.1 x 9.8 x 5....

Manufacturer: CME Tools Brand: CME Tools

CX80 Precision Punch Former and Radius Dresser For precision grinding different shapes of punch and elctrodes of EDM in surface grinder and universal tool grinder. CENTER HEIGHT: 3-1/2", Max. wheel Dia. 8" MAX WHEEL DIA.: 8" Clamping Dia. in V-slot 1/8"-1-1/4" V-Block TRAVEL: 1" Transversal travel of slider +/-1/2" Indexing Div. 24 every 15 degree +/-10" Max. radius when dressind are Convex R-2", Concave R-4" Demensions: 14-1/2" x 4-1/2" x 6"

Manufacturer: AccuVac Technology Brand: AccuVac Technology Model: CF1325-450-250-ST

ACCUVAC TECHNOLOGY Zero Length Reducer.The manufacturer is ISO registered supplier. Vacuum Flanges are manufactured in California using DFARS SS304L ESR material. Flange seal performance specifications are: Leak Rating 10-13 Torr; Temperature Range 200 to 450 deg C. The seal mechanism knife-edge and bolting design are compatible with the industry application standards. We offer 14 day return policy if the product is returned, shipment paid, undamaged and unused.

Manufacturer: AccuVac Technology Brand: AccuVac Technology Model: CF1450-1200-N

Cf14.5 inch knife edge seal flange is similar to Conflat /Del-Seal flange. It is a bored flange with bolt through holes. Vacuum Flanges are manufactured in California using DFARS SS304L ESR material. Flange seal performance specifications are: Leak Rating 10-13 Torr; Temperature Range 200 to 450 deg C. The seal mechanism knife-edge and bolting design are compatible with the industry application standards. We offer 14 day return policy if the product is returned, shipment paid, undamaged and unused.

Manufacturer: AccuVac Technology Brand: AccuVac Technology Model: CF1200-000-R

Cf12 inch knife edge seal flange is similar to Conflat /Del-Seal flange. It is a blank flange with tapped holes. Vacuum Flanges are manufactured in California using DFARS SS304L ESR material. Flange seal performance specifications are: Leak Rating 10-13 Torr; Temperature Range 200 to 450 deg C. The seal mechanism knife-edge and bolting design are compatible with the industry application standards. We offer 14 day return policy if the product is returned, shipment paid, undamaged and unused.

Manufacturer: AccuVac Technology Brand: AccuVac Technology Model: CF1650-1400-RT

Cf16.5 inch knife edge seal flange is similar to Conflat /Del-Seal flange. It is a bored flange with tapped holes. Vacuum Flanges are manufactured in California using DFARS SS304L ESR material. Flange seal performance specifications are: Leak Rating 10-13 Torr; Temperature Range 200 to 450 deg C. The seal mechanism knife-edge and bolting design are compatible with the industry application standards. We offer 14 day return policy if the product is returned, shipment paid, undamaged and unused.

Manufacturer: Long Term Elec. Co.,Ltd. Brand: Zero Model: LPS0520

Automatic ResetOpen on pressure rise1/4" Female SAE mounting 24V,120V,240V,50-60Hz,6RLA,36LRA

Manufacturer: G.S ONLINE STORE Brand: G.S Dental

G.S STAR LIKE POSITIONING BRACKET GAUGE ORTHODONTIC INSTRUMENTS DENTAL LAB