Calibration - Page 75

Manufacturer: VERMONT GAGE Brand: Vermont Gage

NIST traceable. Material: 52100 tool steel Length: 2" Finish: 10µ" or better Within .0001" round. Marked with size & direction of tolerance on gages over .060".

Manufacturer: Fluke Calibration Brand: Fluke Model: 3102-2

FLUKE CALIBRATION 3102-2 INSERT, 3.2MM, 9102S HANDHELD DRY WELL CALIBRATOR

Manufacturer: Ohaus Brand: Ohaus Model: 80850268

The Ohaus metric, stainless steel electronic balance calibration weight meets American Society for Testing and Materials (ASTM) Class 1 specifications, and is designed for calibrating other weights, or electronic balances and scales. The weight has straight sides and a flat top that allows weights to be stacked. It is constructed of stainless steel for stability, resistance to corrosion, and low magnetic susceptibility. The weight meets ASTM E617, Class 1 specification for use as a reference standard for calibrating other weights and high-precision balances with readabilities as low as 0.1mg to 0.01mg. An optional National Voluntary Laboratory Accreditation Program (NVLAP) certificate ensures precision and traceability.The National Voluntary Laboratory Accreditation Program (NVLAP) accredits laboratories for compliance with ISO/IEC 17025 on the basis of their ability to meet the technical requirements set forth in NIST Handbook 150-2, and can provide accreditation to ANSI/NCSL Z540-1-1994. NVLAP calibrations and certifications meet all ISO, FDA, GMP, GLP, DOD, ANSI/NCSL Z540-1 and Nuclear requirements and are traceable to NIST. Procedures and processes used to generate this multi-page certificate, as well as its format and content, are prescribed by NVLAP. The document contains customer name & address, date of calibration, equipment and standards used in the calibration, accuracy class, true mass value (mass in a vacuum), “As Found” mass correction (for recalibration), “As Left” mass correction, uncertainty of measurement process (uncertainty to tolerance ratios are guaranteed), environmental conditions during test, construction and density of the weight, calibration procedure, and a statement of traceability to NIST. Mutual recognition arrangements include The International Laboratory Accreditation Cooperation (ILAC), The Asia Pacific Laboratory Accreditation Cooperation (APLAC) and The National Cooperation for Laboratory Accreditation (NACLA). Calibration weights are used to measure the ...

Manufacturer: SMD / D'amore Engineering Brand: MSD Ignition Model: CC-1

The purpose and benefit of the D'Amore Engineering / SMD Crossover Calibrator. Most modern car audio amplifiers have a built in crossover on the side. Usually, it will start at 30hz and have a huge gap, all the way up to (sometimes) 500hz. The purpose of this tool is to enable the installer to set the crossover frequency of an electronic crossover to the desired frequency, accurately and quickly. Enter "Competition Mode" and easily match gains on any 4-channel amplifier or even multiple bass amplifiers. This is VERY important when using subwoofers that share a common chamber, especially if you have 2 (or more) amplifiers on a dual voice coil driver.

Manufacturer: Fluke Corporation Brand: Fluke Model: GEOX PROBE CABLE

Geox connector cable for selective clamp.

Manufacturer: Hexagon Metrology Brand: Brown & Sharpe

44052 5.000 intrimik ring

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611573-516

All Mitutoyo gage blocks meet or exceed all known specifications. The flatness and parallelism surface finish necessary to achieve the required accuracies are the same as or better than government requirements. A certificate of inspection is furnished with all Mitutoyo gage blocks with a serial number on the case and an identification number on each block. The deviation of each block is registered. For this inspection, each gage block is measured relative to the upper level master using a gage block comparator. Grade K gage blocks are manufactured by absolute measurement using an interferometer. The gage block set and discrete gage block are supplied with a certificate of calibration. The certificate of calibration specifies the deviation from the nominal length. (Comparative measurement, however, is performed for all square gage blocks.). A certificate of accuracy, traceable to the NIST, is furnished with each Mitutoyo gage block set and individual block.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611611-516

All Mitutoyo gage blocks meet or exceed all known specifications. The flatness and parallelism surface finish necessary to achieve the required accuracies are the same as or better than government requirements. A certificate of inspection is furnished with all Mitutoyo gage blocks with a serial number on the case and an identification number on each block. The deviation of each block is registered. For this inspection, each gage block is measured relative to the upper level master using a gage block comparator. Grade K gage blocks are manufactured by absolute measurement using an interferometer. The gage block set and discrete gage block are supplied with a certificate of calibration. The certificate of calibration specifies the deviation from the nominal length. (Comparative measurement, however, is performed for all square gage blocks.). A certificate of accuracy, traceable to the NIST, is furnished with each Mitutoyo gage block set and individual block.

Manufacturer: Ohaus Brand: Ohaus

Weights from 5mg to 30kg are Stainless Steel. Weights from 1mg to 2mg are Aluminum. Weight Sets include a Polycarbonate Case. Individual Weights up to 500mg include a Polypropylene Case. Weights from 1g to 2kg include a Polycarbonate Case. Weights from 4kg to 30kg include a Polypropylene Case.

Manufacturer: Fluke Corporation Brand: Fluke Model: TLK282

Kit includes insulation piercing clip set, automotive back probe pins (five), SureGrip silicone test lead set, SureGrip test probe set. Also includes SureGrip alligator clip set, SureGrip large jaw alligator clip set, SureGrip hook clip set, Soft case. Use the back probe pins to slide into weather pack connectors on fuel injectors, TPS and MAP sensors. A hook probe with plunger actuation allows quick connection to pins or exposed conductors. Tested to 60V DC.