Capacitance & Resistance Meters - Page 4

Manufacturer: AEMC Brand: AEMC

The Ground Resistance Tester Model 6417 measures ground rod and grid resistance and impedance without the use of auxiliary rods and can be used in multi-grounded systems. Bluetooth connectivity through AEMC's PC based DataView® software enables users to configure and retrieve data as well as generate reports. An AndroidTM based app is also available, allowing for configuring, downloading, printing and emailing test results from a tablet or smartphone.

Manufacturer: Megger Brand: Megger Model: 1000-761

The Megger DET14C digital clamp-on ground resistance meter measures ground resistance and current in multi-ground electrical installations and lightning protection systems without needing to disconnect the ground. It has a clamp with two jaws that can close around round cables and rods up to 1.45" (37 mm) in diameter and ground tapes and straps up to 1.96" (50 mm) wide to measure resistance without disconnecting the ground. The meter also provides true RMS (root mean square) measurements of current up to 35 amp to help ensure operator safety during operation. The meter has a user-selectable noise filter to allow measurements to be taken in areas with high amounts of electrical noise. The meter's internal data storage allows multiple results to be compared and tracked over time, and readings are date and time stamped for future reference. An alarm notifies user when user-selected minimum and maximum values for current and resistance are reached or exceeded. The hold function keeps a reading on the display, even after the meter is disconnected. In applications where the conductor is difficult to access, an auto-hold feature allows a reading to be captured without requiring the operator to press the button during measurement. The meter's liquid crystal display (LCD) is backlit to provide readability in low light. The clamp jaws have a smooth surface with no interlocking teeth to help prevent build-up of dirt and residue, which can interfere with measurements. The unit automatically turns off after five minutes of non-use to conserve battery life, and a low-battery indicator signals when the meter's batteries need to be replaced. The Megger DET14C meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category IV installations up to 600V, which covers measurements at the source of the low-voltage supply, such as electricity meters and overcurrent protection devices. The meter has a wrist strap and comes with a hard plastic carrying case to protect the meter from damage during...

Manufacturer: Megger Brand: Megger Model: 1000-324

The Megger DET4TR2 four-terminal ground resistance tester measures earth ground resistance, soil resistivity, and ground voltage to evaluate the safety and integrity of electrical systems. The tester offers a choice of 2-, 3-, or 4- pole ground resistance testing, and it has a maximum resistance input of 20,000 ohms for testing the resistivity of a range of soil types. The tester's voltmeter displays the ground voltage during use, which helps increase operator safety. The operator can choose between 25V or 50V test voltage output, allowing the tester to be used in agricultural applications. For accurate readings in noisy environments, the tester can filter out ground voltage noise up to 40 volts (V) peak-to-peak. The DET4TR2 comes with one 49' (15 m), two 33' (10 m), and one 10' (3 m) test leads, four ground stakes, and four right-angle terminal adaptors. The tester's liquid crystal display (LCD) provides confirmation of the connection and functionality of the potential and current spikes and indicates the level of ground noise that is present.The DET4TR2 meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category IV installations up to 100V, which covers measurements at the source of the low-voltage supply, such as electricity meters and overcurrent protection devices. The tester comes in a hard polypropylene case for transport and storage. The case has an ingress protection rating of IP54, meaning it protects against the ingress of dust and splashing water, making it suitable for outdoor use. The DET4TR2 operates on eight rechargeable 1.5V nickel-metal-hydride (NiMH) AA batteries (included). It has a built-in battery charger and comes with an AC/DC adapter for charging. A low-battery indicator signals when the batteries need to be charged.SpecificationsMaximum ground resistance input20,000 ohmsMaximum ground voltage input100 volts (V)Standards metInternational Electrotechnical Commission (IEC)/European Standards (EN) 61010-1, EN61557, Keuring Electrotechnisch Materi...

Manufacturer: Megger Brand: Megger Model: 1001-936

The Megger MIT515-US insulation resistance tester measures insulation resistance, voltage, current, and capacitance in high-voltage electrical systems. This multiranging digital meter performs timed insulation resistance (IR), polarization index (PI), and dielectric absorption ratio (DAR) tests. The unit measures insulation resistance from 10 kilohms to 10 teraohms, voltage from 30 to 660V alternating current (AC) or direct current (DC), current from 0.01nA to 6mA, and capacitance from 10 nanofarads to 25 microfarads. The unit has test voltages in 10V steps from 50V to 1,000V and in 25V steps from 1,000 to 5,000V. It also has 250, 500, 1,000, 2,500, and 5,000V set test voltages. The tester is safety rated to European Standard EN61010-1, Category IV, 600V. It is Ingress Protection 65 (IP65)-rated to be dust tight and protection against water sprayed from 6.3mm jets. The MIT515-US is used by electricians, electrical contractors, and telecommunications workers.Specifications Insulation resistance range 10 kilohms to 10 teraohms Voltage range 30 to 660V AC/DC Current range 0.01nA to 6mA Capacitance range (above 500V) 10 nanofarads to 25 microfarads Power supply Rechargeable 11.1V Lithium-ion battery Weight 5.4kg / 10 lb. Safety standard met International Electrotechnical Commission (IEC)/European Standards (EN) 61010-1 Cat IV 600V Mechanical standard met IP65, for complete protection from dust and water sprayed rom 6.3mm jets Dimensions 315 x 285 x 181mm / 12 x 11 x 7 inches (H x W x D)H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-functi...

Manufacturer: Megger Brand: Megger Model: 1001-944

The Megger MIT1025-US insulation resistance tester measures insulation resistance, voltage, current, and capacitance in high-voltage electrical systems. This multiranging digital meter performs timed insulation resistance (IR), polarization index (PI), dielectric absorption ratio (DAR), dielectric discharge test (DD), step-voltage (SV), and ramp tests. The unit measures insulation resistance from 10 kilohms to 20 teraohms, voltage from 30 to 660V alternating current (AC) or direct current (DC), current from 0.01nA to 6mA, and capacitance from 10 nanofarads to 25 microfarads. The unit has test voltages in 10V steps from 100V to 2,500V and in 25V steps from 2,500 to 10,000V. It also has 250, 500, 1,000, 2,500, 5,000, and 10,000V set test voltages. The tester is safety rated to European Standard EN61010-1, Category IV, 600V. It is Ingress Protection 65 (IP65)-rated to be dust tight and protection against water sprayed from 6.3mm jets. The MIT1025-US is commonly used by electricians, electrical contractors, and telecommunications workers.Specifications Insulation resistance range 10 kilohms to 20 teraohms Voltage range 30 to 660V AC/DC Current range 0.01nA to 6mA Capacitance range (above 500V) 10 nanofarads to 25 microfarads Power supply Rechargeable 11.1V Lithium-ion battery Weight 5.4kg / 10 lb. Safety standard met International Electrotechnical Commission (IEC)/European Standards (EN) 61010-1 Cat IV 600V Mechanical standard met IP65, for complete protection from dust and water sprayed rom 6.3mm jets Dimensions 315 x 285 x 181mm / 12 x 11 x 7 inchesH is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can ...

Manufacturer: Megger Brand: Megger Model: DLRO200-EN

The Megger DLRO200 series digital microhmmeter measures resistance in switch and breaker contacts, bus-bar joints, and other high-current electrical systems. The meter is autoranging and digital for safety and ease of use. The internal memory stores up to 300 sets of results, which can be annotated with notes by the user. The results and notes can be downloaded to a PC or directly outputted to a printer via the RS232 port. The microhmmeter measures resistance from 0.1 microhms to 1 ohm, with test currents from 10 to 200A. The unit is safety rated to European Standard EN61010-1. The DLRO200 series is used by electricians and electrical contractors.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers, measure one property of a circuit, and multimeters measure multiple properties. Electrical test meters display information either in analog form using a needle that moves on a calibrated scale, or in digital form on an LED screen. Meters have electrical properties that are to be measured and the anticipated range of results, and should have a rating that is higher than the maximum value of the anticipated range. Meters measure electrical properties and are safety rated to measure a specific range of results. The range on the meter should be higher than the maximum anticipated value to be measured. An electrical test meter has multiple settings corresponding to potential ranges of values for the properties it can measure. A manual ranging meter requires the operator to flip through different settings until the correct range is reached. An autoranging meter cycles through range settings automatically until it reaches the correct range. Megger manufactures equipment for cable fault l...

Manufacturer: Echo Brand: ECHO Model: 16201001360

Lead Ground

Manufacturer: Silvercell Brand: Silvercell Color: Green

Waterproof 0.28" DC 3.5-30V Mini Digital LED Voltmeter Volt Meter F 12V Car Moto Features: 1, the voltmeter with full enclosure, potting fully waterproof design, a long soak in the water can still work without damage, more moisture, oil, dust, vibration 2, the voltmeter display uses LED digital tube 0.28 inches 3, the voltage meter wiring simple, just take two lines in the table have reverse protection, reverse does not burn Specification: Dimensions: As shown in the pictures Type: 3 digits 0.28" Led color: blue/red/green/yellow Range: dc 3.50-30.0V Supply voltage: DC3.50-30.0V Cable length: 85mm Fixed hole diameter: 3mm(approx.) Reading per second: 2 The power consumption: Static about 15 mA Accuracy: 1% (¡À1 digit) Operating Temperature: -10¡æ~65¡æ Potting material Epoxy-resin Glue Wiring: Red: Power Supply +, Measure + Black: Power Supply -, Measure ¨C Reverse polarity protection: Yes Application: used for battery voltage measuring on electric vehicles, electric cars, electric motor cars, and so on Package Included: 1x DC Voltmeter(color as you choice)

Manufacturer: DER EE ELECTRICAL INSTRUMENT Brand: DER EE ELECTRICAL INSTRUMENT

Service parts For DE-5000

Manufacturer: MODUTEC Brand: MODUTEC

Modutec Kn3S-Dma-029-U Panel Meter 800V Peak To Gnd (Z 4-10 L29)