Capacitance & Resistance Meters - Page 63

Manufacturer: Fluke Corporation Brand: Fluke Model: 65157MM-AMZN

The Fluke 1587 mdt advanced insulation and motor drive troubleshooting Kit is designed for troubleshooting and preventive maintenance applications including three-phase motors, cables, switch gear, and in applications where testing is required without the need to break the circuit. The Kit includes the Fluke 1587 Digital insulation Multimeter, Fluke I400 current clamp, and Fluke 9040 phase rotation indicator.

Manufacturer: AEMC Brand: AEMC

The Ground Resistance Tester Model 6417 measures ground rod and grid resistance and impedance without the use of auxiliary rods. Clamp-on ground resistance testers can be used in multi-grounded systems without disconnecting or de-energizing the ground system under test it. The Model 6417 simply clamps around the grounding electrode or conductor and measures the resistance to ground. By performing measurements on intact ground systems, the user also verifies the quality of the grounding connections and bonds. Resistance and continuity of grounding loops around pads and buildings may also be measured. Three new features unique to AEMC® are: Test frequency selection provides more accurate results in inductive environments Touch voltage indication  indicates the voltage on the display along with a warning buzzer when the voltage derived from current and resistance measurements detect a potentially dangerous touch condition Loop resistance indication alerts the user to the fact that the measurement may not be ground resistance The Ground Resistance Tester Models 6416 and 6417, measure ground rod and grid resistance without the use of auxiliary rods. Clamp-on ground resistance testers can be used in multi-grounded systems without disconnecting the ground system under test or de-energizing them. The Models 6416 and 6417 simply clamp around the ground conductor or rod and measure the resistance to ground. By performing measurements on intact ground systems, the user also verifies the quality of the grounding connections and bonds. Resistance and continuity of grounding loops around pads and buildings may also be measured. Two new features unique to AEMC ® are test frequency selection and touch voltage indication. The ability to select the test frequency provides more accurate results in inductive environments

Manufacturer: Hioki Brand: Hioki

Hioki 3511-50 LCR Hi-Tester (120Hz and 1kHz)   LCR Hi-Tester × Compact, lightweight single-function model High-speed measurement Comparator function LED display Two interfaces The Hioki 3511-50 LCR HiTESTER features both high performance and high speed measurements with a low price. The minimum measurement time of 5 ms and a basic accuracy of ±0.08% makes the instrument suitable for use on production lines and laboratories. The built-in high speed comparator significantly reduces production line tact time and allows the construction of automatic production lines. The compact body features a clearly visible LED display that facilitates easy operation and allows settings to be confirmed at a glance The PW3360 Clamp on Power Logger is a clamp-type power meter capable of mea- suring lines with from single-phase to three-phase four-wire. The instrument can perform basic measurements including voltage, current, power, power factor, and energy. Hioki LCR Meters and Impedance Analyzers range from 1mHz to 1.3GHz devices to suit a wide range of applications in the testing of electronic components. The 3511-50 is a compact, general purpose LCR meter for on-board testing of capacitors and coils used in electrical equipment and devices such as automotive-related components.   Front View Front View × Measurement display Displays a testing parameter and corresponding measurement. Status display Displays current test conditions, presettings, and other information. Comparator judgment display Displays judgment in comparator mode

Manufacturer: Fluke Corporation Brand: Fluke Model: EI-162BN

The Fluke EI-162BN split core clamp-on transformer allows the Fluke 1623 or Fluke 1625 earth ground tester to take ground loop resistance measurements around transmission line pylons. The split core transformer makes it possible to measure individual resistances for each tower leg without disconnecting ground leads, overhead static wires, or ground wires. The transformer has 1,000 windings, with connections at winding ratios of 1,000, 500, 300, 200, and 0 available to set before use with meter for minimum measuring and maximum parasitic currents expected to flow through the transmission line pylon. The inside diameter of the clamp is 320mm/12.6 inches. The split core transformer includes two fasteners for holding the transformer halves together, a cable bobbin with two 12m/40ft. test leads for connecting the transformer to the tester’s jack, contact clamp, user manual, and a carrying case. If the user owns the non-kit version of the Fluke 1623 or 1625 ground resistance meter, the split core transformer also requires use of a Fluke 2539195 probe cable (sold separately). The Fluke E1-162BN is manufactured in compliance with DIN ISO 9001 quality assurance system. Specifications Transformation ratios 1:1000, 1:800, 1:500, 1:300, and 1:200 Temperature range -10 degrees to 50 degrees C/14 degrees to 122 degrees F Weight 4.9kg/11lb. Dimensions 377mm/15 inches outside diameter, 310mm/12 inches inside diameter, 30mm/1.25 inches depthGround-resistance meters test the condition of a grounding system, and provide resistivity measurements in ohms. The meters are available in digital, analog, and clamp models. Grounding systems protect people and equipment, and provide a safe path for the dissipation of fault currents, lightning strikes, static discharges, EMI and RFI signals, and interference. Regular testing of a grounding system is important for safety and protection of equipment. For example, corrosive soil with high moisture content can degrade ground rods and connections in existing systems and increas...

Manufacturer: Megger Brand: Megger Model: 6410-919

The Megger BM15 5kv insulation resistance tester measures insulation resistance and voltage in electrical installations, building maintenance, and telecom systems. This analog meter has manual test voltage selection for flexibility of use. The unit has four test voltage options at 500, 1,000, 2,500, and 5,000V. The unit measures insulation resistance from 100 kilohms to 20 gigaohms and voltage from 0 to 600V alternating current (AC). The tester is safety rated to European Standard EN61010-1, Category III, 300V and Category I, 600V. The Megger BM15 is commonly used by electricians, electrical contractors, and telecommunications workers.Specifications Power supply 8 AA batteries Voltage testing range 0 to 600V AC Test voltages 500, 1,000, 2,500, and 5,000V Insulation resistance range 100 kilohms to 20 gigaohms Weight 1.2kg / 2.6 lb. Safety standard met International Electrotechnical Commission (IEC)/European Standards (EN) 61010-1 Cat III 300V, Cat I 600V Dimensions 220 x 160 x 115mm / 8.9 x 6.3 x 4.5 inchesH is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers, measure one property of a circuit, and multimeters measure multiple properties. Electrical test meters display information either in analog form using a needle that moves on a calibrated scale, or in digital form using digits or a graphic representation on an LED screen. Meters have electrical properties that are to be measured and the anticipated range of results, and should have a rating that is higher than the maximum value of t...

Manufacturer: Megger Brand: Megger Model: 1001-940

The Megger MIT525-US insulation resistance tester measures insulation resistance, voltage, current, and capacitance in high-voltage electrical systems. This multiranging digital meter performs timed insulation resistance (IR), polarization index (PI), dielectric absorption ratio (DAR), dielectric discharge test (DD), step-voltage (SV), and ramp tests. The unit measures insulation resistance from 10 kilohms to 10 teraohms, voltage from 30 to 660V alternating current (AC) or direct current (DC), current from 0.01nA to 6mA, and capacitance from 10 nanofarads to 25 microfarads. The unit has test voltages in 10V steps from 50V to 1,000V and in 25V steps from 1,000 to 5,000V. It also has 250, 500, 1,000, 2,500, and 5,000V set test voltages. The tester is safety rated to European Standard EN61010-1, Category IV, 600V. It is Ingress Protection 65 (IP65)-rated to be dust-tight and protected against water sprayed from 6.3mm jets. The MIT525-US is commonly used by electricians, electrical contractors, and telecommunications workers.Specifications Insulation resistance range 10 kilohms to 10 teraohms Voltage range 30 to 660V AC/DC Current range 0.01nA to 6mA Capacitance range (above 500V) 10 nanofarads to 25 microfarads Power supply Rechargeable 11.1V Lithium-ion battery Weight 5.4kg / 10 lb. Safety standard met International Electrotechnical Commission (IEC)/European Standards (EN) 61010-1 Cat IV 600V Mechanical standard met IP65, for complete protection from dust and water sprayed rom 6.3mm jets Dimensions 315 x 285 x 181mm / 12 x 11 x 7 inchesH is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to co...

Manufacturer: MCP Brand: Mcp Model: BR2832 Color: Red

The MCP BR2832 is a micro-processor controlled handheld LCR meter with high accuracy, resolution & low power consumption. It can measure 4 primary parameters including inductance, capacitance, resistance, impedance and 4 secondary parameters such as dissipation factor, quality factor, phase angle and ESR (Equivalent Series Resistance), both primary and secondary parameters are simultaneously shown on the back-lit LCD display. The BR2832 has wide measuring ranges, 0.1uH to 1,000 H for inductance, 0.1pF to 20mF for capacitance, 0.1mohm to 10 Mohm for resistance and impedance. And it provides a maximum reading of 40,000 for the primary parameter and a reading resolution of 0.0001 for the secondary parameter, the maximum measuring frequency of up to 100 KHz and constant internal resistance of 100 ohms and testing level of 0.6 Vrms. The auto range can instantly display the measuring results and automatically choose the desirable testing parameters based on components properties. Its measuring accuracy is up to 0.2%. Front panel push buttons maximize the convenience of function and feature selection such as frequency, rate and L/C/R/Z selection. Tolerance mode can sort components, record mode aids to capture readings, convenient open/short clear function improves the measuring accuracy, and utility menu helps you easily take the selections of the key tone, auto power-off and storage. The BR2832 is also equipped with a mini USB date port to be connected to a Windows PC for instant data transfer , ideal for applications that require remote control and data acquisition. What's in the box: MCP BR2832 LCR meter 4-Terminal Kelvin Test Clip leads Short-circuit plate 7.2V rechargeable battery (installed) AC/DC adapter User manual

Manufacturer: V&A Brand: V&A Model: VA503 Color: Black and Red

Surface mount devices are usually tiny and without wire leads, making it much more difficult to test and identify SMD than conventional components. The V&A VA503 gives users an easy way to sort and evaluate loose components and to perform on-board measurements and debugging. Precise tips made of non-magnetic steel are able to pick and reliably contact even smallest SMD components, or take measurements from the devices already mounted on a board. The probe can also be used to test conventional components with wire leads too short to insert into the test terminals. The VA503 has 6 resistance measurement ranges from 0 to 400 ohms, up to 4M ohms, for capacitance measurement, there are also 6 ranges from 0 to 4nF up to 200 uF, you can also use it to do diode test.

Manufacturer: RioRand Brand: RioRand Model: RR-HU-LM-IC

Features: 100% brand new and high quality Power: 9V battery(6F22) (not included) or USB power LCD size: 40 X 63mm Color: Red + Grey Weigh: 374g Size: 96 X 193 X 47mm Special Function: Max. Display: 19999 D/Q Max. Display: 1999 D/Q Resolution: 0.001 Automatic Range Real time display for measuring frequency Measurement Models: series and parallel Power off automatically Low voltage display: ≤6.8V Data hold Relative measurement USB Data transmission USB Port /PC Data recording: 60000 Analog bar: 26pcs LCD backlight LCR Auto identification measurement Voltage Basic Function Range Accuracy L (H) 20uH/200uH/20mH/200mH/ 2000mH/20H/200H2000H/20KH ±(0.5%+5) C (F) 200pF/2nF/20nF/200nF/ 2000nF/20uF/200uF/2000uF/20mF ±(0.5%+5) R (Ω) 20Ω/200Ω/2KΩ/20KΩ/200KΩ/ 2MΩ/20MΩ/200MΩ ±(0.3%+5) Frequency 100Hz/120Hz/1KHz/10KHz/100KHz Voltage 0.6Vrms Parameters L/C/R/DCR/Q/D/θ/ESR Package includes: 1x LCR Meter 1x SMD Test Clip 1x USB Cable 1x CD Software 1x Socket Adapter 1x Short-circuit Plate 1x Carrying Case

Manufacturer: FLIR Systems Brand: Extech Model: MG300

View larger CAT IV Insulation Tester/MultiMeterwith Wireless PC Interface The MG300 is a True RMS multimeter with built-in insulation resistance tester with the added safety of wireless data streaming for remote monitoring and datalogging. By adding insulation testing capabilities to the ubiquitous digital multimeter, electricians are always equipped for insulation testing, helping to make it a more routine part of predictive maintenance with faster troubleshooting and repairs without additional tools. Features Overview The rugged and waterproof (IP67-rated) combination meter includes a digital insulation resistance tester (or megohmmeter) with 4 different test voltages for measuring resistance up to 4 GΩ with 0.001MΩ resolution. The full-function, true RMS digital multimeter includes useful extras like duty cycle measurements and milliamp readings for analog 4-20mA current loops in industrial analog process controls. The CAT IV-rated meter’s wireless data streaming enables safer troubleshooting and maintenance on dangerous moving equipment and one-person operation of remote safety switches. Technicians can focus on finding problems by monitoring real-time readings on a laptop or computer screen from safe distances – up to 30 feet away. Includes The MG300 comes with remote USB receiver, Windows compatible software, test leads with alligator clips, Type K bead wire temperature probe with adapter, carrying case, 6 AA batteries, and user manual. The MG300 is available with NIST-traceable certification (model MG300-NIST). For users outside North America, the MG302 which transmits data at 433MHz instead of 915MHz is also available. View larger Key Features AC/DC Voltage AC/DC Current Resistance Capacitance Frequency(electrical & electronic) Duty Cycle Diode Test Insulation Resistance Continuity Thermocouple Temperature