Indicators - Page 122

Manufacturer: HHIP Brand: HHIP Model: 4401-0538

220 Lbs Pull Heavy-Duty Universal Magnetic Base 220 Lbs Pull Heavy-Duty Universal Magnetic Base 3-D rigid aluminum arm movement. Unique central locking mechanism. On/Off switch. Accepts all AGD dial indicators and test indicators. Fine adjustment. Base is 74 X 50 X 55mm. Maximum reach is 16.0".

Manufacturer: Q-Mark Manufacturing Inc Brand: Q-Mark

Extra long M5 stylus, 1.5 mm silicon nitride ball, carbide stem, 11.0 mm diameter by 50.0 mm long stainless steel base. Overall stylus length is 60.0 mm. Stylus weight is 11.21 grams.

Manufacturer: Q-Mark Manufacturing Inc Brand: Q-Mark

M5 stylus, 0.5 mm ruby ball, tapered carbide stem, 11.0 mm diameter x 10.0 long stainless steel base. Minor stem diameter is 0.3 mm, major stem diameter is 1.0 mm. Overall stylus length is 25.0 mm. Stylus weight is 5.72 grams.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 1410SB-10 Color: White

The Mitutoyo dial indicator has a black or white face, a choice of flat or lug, a 0.375" stem diameter, and inch measurements. The indicator has a 0.375" diameter stem, a #4-48 UNF contact point thread mount, and is used to measure surface variations in fractional inches. The choice of black or white dial and a contrasting hand help make measurements easy to read. The dial indicator comes with a choice of flat or lug back for a variety of mounting options. Flat back dial indicators are either clamp-mounted on the stem or plate-mounted on the rear of the indicator. Lug back dial indicators have a protrusion with a hole to mount the indicator using a lug or nut and bolt. Lug back dial test indicators usually come with the lug installed horizontally. The back on most indicators can be rotated to the vertical position. It has a stem design that provides a long clamping range, no through screw-holes on the frame for dust- and water resistance, and an involute curved lifting lever that provides smooth movement of spindle and dovetail joint for a tool-less connection. This dial indicator meets ANSI standards, Japanese Industrial Standard (JIS) B7503-1997, and American Gage Design (AGD) standards for face and thread size, and bezel and stem diameter. Dial readings with three digits, such as 0-10-0, signify that the indicator has a balanced dial. Dial readings with two digits, such as 0-100, indicate that the dial has a continuous dial. Balanced dials are used to read the difference from a specific surface reference point. Continuous dials are used for direct readings and usually have a larger measurement range than balanced dials. Optional features include jeweled bearings for high sensitivity and accuracy, a revolution counter to measure overall change, waterproof, dustproof, shockproof, a white or black face, and reverse reading for depth or bore gage measurement.Dial indicators are also called dial gauges, dial calipers, and probe indicators. These precision measuring tools are used to accurately measure small linear ...

Manufacturer: PHASE II Brand: PHASE II

These testers are crafted and engineered to perform at the highest level of accuracy. An ergonomic and attractive design combined with lightweight assists in taking precise hardness measurements. Accurate and repetitive deviation = 20~90 HSA; HSA

Manufacturer: Flexbar Brand: Flexbar

Centering Microscope. Adapts to any Machine spindle With maximum accessibility to the operator. 45X Magnification for optical Position accuracy of .0001". Single dash Line Reticle for easy observation of the work Reference line. Unique compensation of spindle runout by adjustment Screw. Straight shank 1/2" Diameter, eyepiece Angle 60°. Field of view .100" Diameter, focal length 5/8". Optional Edge Block to locate the Edge of any work piece to the spindle axis, and V-Block Gage for Precision Centering of a V-Block to the spindle for cross axis boring. Model No. 17273, Edge Block for Centering Microscope (Model No. 17272).

Manufacturer: HHIP Brand: HHIP

3.75 X 2.75 X 5 Magnetic V-Block with Switch ~ Precision ground and finished working surfaces. ~ On/off switch. ~ Two-centered 90° vees. ~ 275 lbs. of power pull. ~ Ideal for scribing, grinding, measuring and machining round or irregular shaped items.

Manufacturer: Johnson Level & Tool Brand: Johnson Level & Tool Model: 1455-0100

Johnson level 1455-0100 Digital Indicators, The operator can toggle between inch and millimeter at any position,Unit has a 360 degree rotating bezel, The digital indicator can measure in relative and absolute measurements, This unit also has an upper limit and lower limit preset, You can toggle between minimum, maximum and total indicator readings, Unit can also operate in plus or minus travel direction, There is an output jack that allows data transmission, and data output can be used by a variety of peripherals for analysis, data collection and hard copy documentation-data output is RS232.

Manufacturer: Hexagon Metrology Brand: Brown & Sharpe Color: White

The Brown & Sharpe TESA Tesatast series dial test indicator has a white face, a 0.0787" stem diameter, and inch measurements. The indicator can make either horizontal or vertical measurements, and the choice of white or yellow dial help make measurements easy to read. The yellow face with contrasting black hand complies with ANSI standards for metric dial faces. The carbide, ball-contact tip reaches into the workpiece for accurate measurements of turned, milled, and ground parts, and for tool setting gauges, fixtures, and inspections. The continuous clockwise pointer rotation helps prevent plus or minus confusion and displays reading in fractional inches. The ball-bearing lever system swivels through to 180 degrees. The dial face mounted at the top of the indicator parallel to the axis, and three universal dovetail mounts can be used for mounting from the top, front, or back. Dovetail mounts provide a rigid setup. This indicator has a Monoblock body design with pinions mounted in jeweled bearings in an isolated assembly separate from the outer body, for high accuracy. It is anti-magnetic for safety when used around magnetic workpieces and debris, and has full-metal construction for durability and corrosion resistance. This dial test indicator meets Deutsches Institut fur Normung (DIN) 2270, and Norme Francaise (French Institute for Standardization) NF E 11-053 standards, and includes an identification number and a declaration of conformity. The set includes a dial test indicator, a 0.080" (2mm) ball-end carbide contact point, a 0.310"(8mm) extension with dovetail, a point key, a Certificate of Accuracy and Traceability, and a storage box. Dial readings with three digits, such as 0-10-0, signify that the indicator has a balanced dial. Dial readings with two digits, such as 0-100, indicate that the dial has a continuous dial. Balanced dials are used to read the difference from a specific surface reference point. Continuous dials are used for direct readings and usually have a larger measurement range than balanced ...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 2904SB Color: White

The Mitutoyo dial indicator has a black or white face, a choice of flat or lug, a 0.375" stem diameter, and inch measurements. The indicator has a 0.375" diameter stem, a #4-48 UNF contact point thread mount, and is used to measure surface variations in fractional inches. The choice of black or white dial and a contrasting hand help make measurements easy to read. The dial indicator comes with a choice of flat or lug back for a variety of mounting options. Flat back dial indicators are either clamp-mounted on the stem or plate-mounted on the rear of the indicator. Lug back dial indicators have a protrusion with a hole to mount the indicator using a lug or nut and bolt. Lug back dial test indicators usually come with the lug installed horizontally. The back on most indicators can be rotated to the vertical position. It has a stem design that provides a long clamping range, no through screw-holes on the frame for dust- and water resistance, and an involute curved lifting lever that provides smooth movement of spindle and dovetail joint for a tool-less connection. This dial indicator meets ANSI standards, Japanese Industrial Standard (JIS) B7503-1997, and American Gage Design (AGD) standards for face and thread size, and bezel and stem diameter. Dial readings with three digits, such as 0-10-0, signify that the indicator has a balanced dial. Dial readings with two digits, such as 0-100, indicate that the dial has a continuous dial. Balanced dials are used to read the difference from a specific surface reference point. Continuous dials are used for direct readings and usually have a larger measurement range than balanced dials. Optional features include jeweled bearings for high sensitivity and accuracy, a revolution counter to measure overall change, waterproof, dustproof, shockproof, a white or black face, and reverse reading for depth or bore gage measurement.Dial indicators are also called dial gauges, dial calipers, and probe indicators. These precision measuring tools are used to accurately measure small linear ...