Insulation Resistance Meters - Page 3

Manufacturer: Amprobe Brand: Amprobe Model: AMB-50

The Amprobe AMB-50 industrial high-voltage insulation resistance tester is a digital meter that measures insulation resistance and voltage to help reduce shock hazards and downtime on electrical systems that include wires, cables, transformers, surge arresters, generators, and electrical motors. The tester has automatic range selection for increased safety. The unit measures 0 to 600V alternating current (AC) or direct current (DC) and insulation resistance from 0 to 1 teraohms using 500, 1,000, 2,500, or 5,000V DC test voltage. A low-resistance range (0 to 4,000 ohms) is used to measure resistance in motor windings. The internal memory holds up to 18 test results for later download to a PC using the included USB cord. The tester is safety rated to European Standard (EN) 61010-1, Category III, 600V. The unit has a programmable timer to perform Dielectric Absorption Ratio Tests, Polarization Index (PI) tests, and comparison tests. The tester is powered by eight C batteries (included). The AMB-50 is designed for use by electricians and electrical contractors. Specifications Power supply (8) C batteries (included) Insulation resistance range 0 to 1 teraohm Test voltages 500, 1,000, 2,500, or 5,000V DC AC and DC voltage range 30 to 600V Weight (including batteries) 4.4 lbs./2kg Dimensions 202 x 155 x 94mm (H x W x D)H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers, measure one property of a circuit, and multimeters measure multiple properties. Electrical test meters display information e...

Manufacturer: Megger Brand: Megger Model: 6220-787

The Megger 6220 series four-piece duplex test lead set includes two current leads with spring clamps and two potential leads with crocodile clips are for use with the Megger DLRO200 digital microhmmeter. These current and potential test leads are for taking four-wire resistance measurements, which are more accurate than two-wire resistance measurements and allow low resistance values to be detected. The spring clamps have a 2.4" (60 mm) jaw opening, and the crocodile clips (also known as alligator clips) have a 0.9" (22 mm) jaw opening. Both the spring clamps and crocodile clips provide hands-free connection to a conductor. The leads have a maximum current input of 200 amp.A test probe, test lead, test prod, or scope probe transmits an electrical signal to a testing device for display and analysis. Designs range from simple test leads with probe-style or clamp-on tips to more complex oscilloscope probes and current detectors. Some test probes, such as basic test leads, have wires with tips for connecting to test equipment. Other test probes, such as voltage detectors, are built into the meter. Depending on what is to be tested, the probe might either be passive or have active parts that require external power to operate. Some probes require contact for testing, while some are capable of taking measurements from a distance. Some also have finger barriers, insulation, or other features to help protect the operator's hand from electrical shock and burns. Test probes are rated according to the amount of voltage, current, temperature, or other input they can measure. When choosing a test probe, the maximum amount of input that the probe can measure should match or exceed both the maximum amount that can be tested by the test equipment, as well as that of the property expected to be present in the application.Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integrity, and power quality testing under multiple brand names, among them Megger, Biddle, States, and...

Manufacturer: Megger Brand: Megger Model: 6111-024

The Megger 6111 series duplex test lead with helical spring-point duplex hand spikes is for use with Megger DLRO10HD, DLRO10, DLRO10X, and BT51 digital microhmmeters. This duplex test lead measures both current and resistance when taking four-wire resistance measurements, which are more accurate than two-wire resistance measurements and allow low resistance values to be detected. The helical spring-point hand spikes compress and rotate to make contact with a conductor. There is 0.4" (10 mm) between the current and potential probe tips on the duplex hand spikes.A test probe, test lead, test prod, or scope probe transmits an electrical signal to a testing device for display and analysis. Designs range from simple test leads with probe-style or clamp-on tips to more complex oscilloscope probes and current detectors. Some test probes, such as basic test leads, have wires with tips for connecting to test equipment. Other test probes, such as voltage detectors, are built into the meter. Depending on what is to be tested, the probe might either be passive or have active parts that require external power to operate. Some probes require contact for testing, while some are capable of taking measurements from a distance. Some also have finger barriers, insulation, or other features to help protect the operator's hand from electrical shock and burns. Test probes are rated according to the amount of voltage, current, temperature, or other input they can measure. When choosing a test probe, the maximum amount of input that the probe can measure should match or exceed both the maximum amount that can be tested by the test equipment, as well as that of the property expected to be present in the application.Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integrity, and power quality testing under multiple brand names, among them Megger, Biddle, States, and AVO. The company, founded in 1889, is headquartered in Dover, England, and meets International Organization for St...

Manufacturer: Amprobe Brand: Amprobe Model: AMB-50-AMZN

The amprobe amb-50 industrial high-voltage insulation resistance tester is a Digital meter that measures insulation resistance and Voltage to help reduce shock hazards and downtime on electrical systems that include wires, cables, transformers, surge arresters, Generators, and electrical motors. The tester has automatic range selection for increased Safety. The unit measures 0 to 600V alternating current (AC) or direct current (DC) and insulation resistance from 0 to 1 teraohms using 500, 1,000, 2,500, or 5,000V DC Test Voltage. A low-resistance range (0 to 4,000 OHMS) is used to measure resistance in motor windings. The internal Memory holds up to 18 Test results for later download to a PC using the included USB cord. The tester is Safety rated to European standard (EN) 61010-1, category III, 600V. The unit has a programmable Timer to perform dielectric absorption ratio tests, polarization Index (pi) tests, and Comparison tests. The tester is powered by eight C batteries (included). the amb-50 is designed for use by electricians and electrical contractors.

Manufacturer: Megger Brand: Megger Model: MIT40X-EN

The Megger MIT40X series insulation tester is an insulation resistance meter with built-in voltmeter for measuring insulation resistance, voltage, and continuity in commercial avionics, military communications, component, and other special-use systems. The autoranging digital meter includes true root mean square (TRMS) and direct current (DC) voltage measurement. The unit has variable test voltages from 10 to 100V in 1V steps. The tester measures insulation resistance from 2 to 20 gigaohms, continuity from 0.01 to 100 ohms, and voltage from 0 to 600V. The dual LCD screen indicates test results either digitally or with an analog arc function to replicate the response of analog meters. The unit has a voltage detection test inhibit feature prevents testing when a circuit has a voltage of greater than 50V. The tester is safety rated to European Standard EN61010-1, Category IV, 600V and is also Ingress Protection 54 (IP54)-rated for protection against dust and splashing water. The Megger MIT40X is used by electricians and electrical contractors.Specifications Test voltages 10 to 100V in 1V steps Automatic continuity testing range 0.01 to 100 Ohms (0-50 Ohms on analog range) Voltage testing range 0 to 600V DC or TRMS Voltage test inhibit level 50V Power supply 5 AA alkaline or rechargeable batteries Weight 590g / 20.73oz. Safety standard met International Electrotechnical Commission (IEC)/European Standards (EN) 61010-1 Cat IV 600V Mechanical standard met IP54, for protection from dust and splashing water Dimensions 220 x 92 x 50mm / 8.66 x 3.63 x 1.97 inchesH is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and lead...

Manufacturer: Extech Instruments Brand: Extech Model: MG500

Digital High Voltage Insulation Tester The MG500 is a CAT III-300V insulation tester capable of performing voltage tests up to 10 kilovolts (500 volts to 10 adjustable in 500 volts steps), with insulation resistance from 800 k to 500 GΩ (autoranging) plus, polarization index (PI) measurement and dielectric absorption ratio (DAR) measurement. The MG500’s EnerSave function limits test duration to 10 seconds to conserve battery power. What's in the Box Comes complete with built-in heavy duty carrying case, test leads, alligator clips, eight C-size batteries, and user manual. Specifications Insulation Resistance = 1M, 2M, 10M, 20M, 100M, 200M, 2G, 20G, 100G, 500GΩTest Voltages = 500V, 1000V, 2500V, 5000V, 10000VPolarization Index = YesDielectric Absorption Ratio = YesVoltage Output Warning = YesAutomatic Discharge = YesDimensions = 13 x 10.2 x 6.3 inches (330x260x160 mm)Weight = 7.9 pounds (3.6 kg)

Manufacturer: Megger Brand: Megger Model: 1001-289

The Megger BM5200 tester is a battery powered instrument with digital and analogue arc display, designed for high voltage insulation resistance testing in the maintenance and servicing of cables, rotating plant machinery, transformers, switchgear and industrial installations.

Manufacturer: Megger Brand: Megger Model: 6410-920

The Megger MJ15 5kv insulation resistance tester measures insulation resistance and voltage in electrical installations, building maintenance, and telecom systems. This analog meter has manual test voltage selection for flexibility of use. The unit is powered by a hand-cranked generator or 8 AA batteries so that it always has a power source. The unit has four test voltage options at 500, 1,000, 2,500, and 5,000V. The unit measures insulation resistance from 100 kilohms to 20 gigaohms and voltage from 0 to 600V alternating current (AC). The tester is safety rated to European Standard EN61010-1, Category III, 300V and Category I, 600V. The Megger MJ15 is commonly used by electricians, electrical contractors, and telecommunications workers.Specifications Power supply 8 AA batteries or hand-cranked generator Voltage testing range 0 to 600V AC Test voltages 500, 1,000, 2,500, and 5,000V Insulation resistance range 100 kilohms to 20 gigaohms Weight 1.2kg / 2.6 lb. Safety standard met International Electrotechnical Commission (IEC)/European Standards (EN) 61010-1 Cat III 300V, Cat I 600V Dimensions 220 x 160 x 115mm / 8.9 x 6.3 x 4.5 inchesH is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers, measure one property of a circuit, and multimeters measure multiple properties. Electrical test meters display information either in analog form using a needle that moves on a calibrated scale, or in digital form using digits or a graphic representation on an LED screen. Meters have electrical properties...

Manufacturer: ACE Brand: ACE

Clip Insulation Test.

Manufacturer: ZhuHai JiDa HuaPu Instrument Co.,Ltd Brand: HoldPeak

This digital insulation tester is an ideal instrument that can be used in testing insulation of electric machines, cables, electronic equipment, electric facilities, etc. Its main features include: easy to operate, wide test range, highly stable performance, backlit LCD display and data hold. Using a shoulder strap, it can be used by both hands. Insulation resistance text range: 1~200MΩ (Basic accuracy: ±(3.0%+5)) 200MΩ~10GΩ (Basic accuracy: ±(5.0%+5)) 10GΩ~200GΩ (Basic accuracy: ±(10.0%+5)) ACV text range: 0~750V (Basic accuracy: ±(2.0%+5), Resolution: 1V) Special function: Continuity alarm: Less than 50Ω±10Ω Data hold: Yes LCD backlight: Approx 10Sec. Function protection: Yes Low Battery Indication: Yes Input impedance: 10MΩ Sampling rate: 3 times/Sec. AC frequency response: 40-400Hz Operation mode: Auto range Max display: 1999 Power source: 6 x 1.5V AA battery(Included) Package Content: 1 x Digital Insulation Tester 2 x Test lead 1 x Shoulder strap 6 x 1.5V batteries (Note: Sometimes we put the batteries in the battery compartment directly, please reposition the batteries correctly before you use.) 1 x User Manual