Insulation Resistance Meters - Page 5

Manufacturer: Megger Brand: Megger Model: 6410-866

The Megger 212000 series insulation resistance tester measures insulation resistance and voltage in electrical installations, building maintenance, and electrical testing. The average-sensing meter help provide accurate readings when measuring linear loads, where the current or voltage has a sinusoidal waveform. This analog meter has manual range selection for flexibility of use and a guard terminal to eliminate surface current leakage. Selectable test currents allow use in a variety of applications. The tester is safety rated to European Standard EN61010-1, Category II, 300V and Category I, 600V. The Megger 212000 series is commonly used by electricians and electrical contractors.Specifications Voltage testing range 0 to 600V DC or TRMS Voltage test inhibit level 75V Weight 1kg / 2.3 lb. Safety standard met International Electrotechnical Commission (IEC)/European Standards (EN) 61010-1 Cat II 300V, Cat I 600V Dimensions 130 x 125 x 180mm / 5.1 x 4.9 x 7 inchesH is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers, measure one property of a circuit, and multimeters measure multiple properties. Electrical test meters display information either in analog form using a needle that moves on a calibrated scale, or in digital form using digits or a graphic representation on an LED screen. Meters have electrical properties that are to be measured and the anticipated range of results, and should have a rating that is higher than the maximum value of the anticipated range. An electrical test meter has...

Manufacturer: wonderfullife.diy Brand: wonderfullife.diy

FEATURES: SMART AS907A digital pressure megger, insulation resistance tester, digital megger .500V / 1000V / 2500V is often called megger or high impedance meter; for measuring generators, motors, power transformers, distribution lines, appliances and other electrical devices (such as control, signaling, communications and power cable) insulation resistance. ACV test frequency: 50 / 60Hz Working temperature and humidity: 0 ~ 40C,

Manufacturer: Extech Brand: Extech Model: MG310

The MG310 is a Compact Insulation Resistance Tester which allows quick and easy testing/troubleshooting of motors, transducers and other industrial appliances. Wide range measurement up to 1000V with Insulation Resistance to 5.5GΩ. Includes an easy snap on protective hard cover and soft pouch to conveniently transport your meter and accessories to the next job site or to safely store away. Featuring Low Resistance measurement with Zero function, Continuity beeper, Large 2000 count dual display with backlight, High voltage and overload indication, Auto-discharge and voltage output warning functions as well as Low battery indication. Complete with test leads, alligator clips, 6 x AA batteries, hard cover and soft carrying case.

Manufacturer: Yokogawa Electric Corporation Brand: Yokogawa Model: MY10-01

The Yokogawa analog megohmmeter is an insulation tester with a single test voltage for measuring insulation resistance to indicate the condition of windings or cables in motors, switchgears, electrical installations, and other insulated equipment, and it also measures AC voltage and lights an LED to indicate that a circuit is live. When measurement is complete and the test button is released, residual voltage is automatically discharged from the circuit under test. The meter has a battery voltage check that indicates the condition of the batteries. It is rated for category (CAT) III installations, which covers equipment in fixed installations, such as switches in the fixed installation and some industrial equipment that is permanently connected to the fixed installation. It comes with a line probe, an earth probe, a display cover, a shoulder strap, four AA batteries, and instructions. Megohmmeters are commonly used for electrical maintenance and testing in industries such as HVAC, transportation, manufacturing, mining, and utilities, among others.SpecificationsAvailable test voltage/insulation resistance ranges125V/20MΩ; 250V/50MΩ; 500V/100MΩ; 500V/1,000MΩ; 1,000V/2,000MΩMaximum AC voltage measured250V for 125V/20MΩ model; 300V for 250V/50MΩ model; 500V for other modelsInstallation categoryCAT IIIStandards metEN safety standards 61010-1:1993 and 61010-2-031:1995; CE markingPower(4) AA batteriesWeight500gDimensions (H x W x D)*103 x 125 x 53mm*H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Megohmmeters, also called insulation testers, are electrical test meters that measure resistance to the flow of current in an electrical component or circuit and check the continuity of an electrical circuit to detect electrical problems such as degraded insulation and improper circuit connections in equipment, wiring, and power supplies. Resistance is an indicator of the overa...

Manufacturer: S Brand: CAMPELIFY

Manufacturer: Kyoritsu Brand: Kyoritsu Model: 3021

The Kyoritsu digital megohmmeter is an auto-ranging insulation tester with four test voltages for measuring insulation resistance to 2,000MΩ to indicate the condition of windings or cables in motors, switchgears, electrical installations, and other insulated equipment, and it also measures low-resistance to 400Ω and AC and DC voltage to 600V, lighting a warning indicator and sounding a buzzer when a live circuit is detected. The comparator function allows a reference resistance value to be set, lights a "pass" or "fail" indicator for subsequent readings, and triggers a buzzer when a reading exceeds the reference value. Up to 99 insulation resistance readings can be stored in the unit's internal memory. When measurement is complete and the range selector is switched off, residual voltage is automatically discharged from the circuit under test. The test button can be locked for extended measurement sessions. The meter has an LCD with a backlight for visibility in low light that automatically turns off after 60 seconds. The display shows readings numerically and in a bar graph. Megohmmeters are commonly used for electrical maintenance and testing in industries such as HVAC, transportation, manufacturing, mining, and utilities, among others.This auto-ranging meter automatically selects the appropriate operating range for measurements. It is rated for category (CAT) III installations to 600V, which covers equipment in fixed installations, such as switches in the fixed installation and some industrial equipment that is permanently connected to the fixed installation. It automatically turns off after 15 minutes of non-use to conserve battery life and has a low-battery indicator that signals when the batteries need to be replaced. It comes with a set of test leads with a remote control switch for initiating a test, a test bar, a safety alligator clip, an extension prod, a test lead storage pouch, six AA batteries, and instructions. SpecificationsMaximum insulation resistance measured2,000MΩTest voltagesB009TAL7K...

Manufacturer: HIOKI Brand: Hioki

HIOKI HIOKI IR4056-20 INSULATION TESTER, 50/125/250/500/1000V

Manufacturer: Megger Brand: Megger Model: 242104-2-26

The Megger 242104-2 series duplex test lead with C-clamp is for use with Megger 247100, 247101, DLRO200, and DLRO600 digital low-resistance ohmmeters. This duplex test lead measures both current and resistance when taking four-wire resistance measurements. The lead has a maximum test current input of 100 amp. The C-clamp provides a hands-free connection to a conductor and can accommodate conductors up to 4" (10 cm). The C-clamp directs the current through the clamp and screw and the potential through a four-point anvil that is insulated from the clamp.A test probe, test lead, test prod, or scope probe transmits an electrical signal to a testing device for display and analysis. Designs range from simple test leads with probe-style or clamp-on tips to more complex oscilloscope probes and current detectors. Some test probes, such as basic test leads, have wires with tips for connecting to test equipment. Other test probes, such as voltage detectors, are built into the meter. Depending on what is to be tested, the probe might either be passive or have active parts that require external power to operate. Some probes require contact for testing, while some are capable of taking measurements from a distance. Some also have finger barriers, insulation, or other features to help protect the operator's hand from electrical shock and burns. Test probes are rated according to the amount of voltage, current, temperature, or other input they can measure. When choosing a test probe, the maximum amount of input that the probe can measure should match or exceed both the maximum amount that can be tested by the test equipment, as well as that of the property expected to be present in the application.Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integrity, and power quality testing under multiple brand names, among them Megger, Biddle, States, and AVO. The company, founded in 1889, is headquartered in Dover, England, and meets International Organization for Standardiza...

Manufacturer: Megger Brand: Megger Model: 6410-957

The Megger 212000 series insulation resistance tester measures insulation resistance and voltage in electrical installations, building maintenance, and electrical testing. The average-sensing meter help provide accurate readings when measuring linear loads, where the current or voltage has a sinusoidal waveform. This analog meter has manual range selection for flexibility of use and a guard terminal to eliminate surface current leakage. Selectable test currents allow use in a variety of applications. The tester is safety rated to European Standard EN61010-1, Category II, 300V and Category I, 600V. The Megger 212000 series is commonly used by electricians and electrical contractors.Specifications Voltage testing range 0 to 600V DC or TRMS Voltage test inhibit level 75V Weight 1kg / 2.3 lb. Safety standard met International Electrotechnical Commission (IEC)/European Standards (EN) 61010-1 Cat II 300V, Cat I 600V Dimensions 130 x 125 x 180mm / 5.1 x 4.9 x 7 inchesH is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers, measure one property of a circuit, and multimeters measure multiple properties. Electrical test meters display information either in analog form using a needle that moves on a calibrated scale, or in digital form using digits or a graphic representation on an LED screen. Meters have electrical properties that are to be measured and the anticipated range of results, and should have a rating that is higher than the maximum value of the anticipated range. An electrical test meter has...

Manufacturer: Amprobe Brand: Amprobe Model: AMB-55

The Amprobe AMB-55 industrial high-voltage insulation resistance tester is a digital meter that measures insulation resistance, current, capacitance, and voltage to help reduce shock hazards and downtime on electrical systems that include wires, cables, transformers, surge arresters, generators, and electrical motors. The tester has automatic range selection for increased safety. The unit measures 0 to 600V alternating current (AC) or direct current (DC), current from 0 to 5.5mA, capacitance from 0 to 50 microfarads, and insulation resistance from 0 to 10 teraohms using DC test voltages from 250 to 5,000V in 25V increments. The internal memory holds up to 1,000 test results for later download to a PC using USB or RS232 data interfaces. The tester is safety rated to European Standard (EN) 61010-1, Category IV, 600V. The unit has a programmable timer to perform Dielectric Absorption Ratio (DAR), Polarization Index (PI), dielectric discharge (DD), and step voltage tests. The tester is powered by six C batteries (included). The AMB-55 is designed for use by electricians and electrical contractors. Specifications Power supply (6) C batteries (included) Insulation resistance range 0 to 10 teraohms Test voltages 250 to 5,000V DC in 25V increments AC and DC voltage range 0 to 600V Current range 0 to 5.5mA Capacitance range 0 to 50 microfarads Weight (including batteries) 6.6 lbs./3kg Dimensions 12 x 5 x 10 inches/31 x 13 x 25cm (H x W x D)H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers,...