|
|
-
4.0 of 5.0 with 26 Reviews
SALE PRICE: $155.00 1% OFF
Manufacturer: Flexbar
Brand: Flexbar
Manufacturer: Flexbar
Brand: Flexbar
|
Flexbar Sensing-Saf-Start. The inexpensive Solution to OSHA. Anti-automatic Restart Protection Without the High Cost of Magnetic Motor Starters This is a mandatory OSHA safety requirement. With the Sensing-Saf-Start correctly installed on existing equipment, it will Provide Protection against unexpected start-up, motion, and motor burn-out in the following manner: Voltage drop or power interruption Protection. in the event equipment, while being operated (switch in the "On" Position), should stop due to loss or drop of Electrical power due to Power Failure from any cause, the Sensing-Saf-Start will automatically Disconnect and shut off power to the equipment, so that upon restoration of power, the equipment will not start up even though the power switch to the equipment is in the "On" Position. in order to restore power to the equipment, the equipment switch must be turned "off" first, and then the Reset button on the Sensing-Saf-Start depressed. in the event the equipment is inadvertantly unplugged and then Plugged Back into the power source while the equipment switch is in the "On" Position, the equipment will not restart until the Reset button on the Sensing-Saf-Start is depressed. The Sensing-Saf-Start is intended for installation on equipment which operates on 120-volts or 240-volts A.C. and which is connected to the source of Electric power by means of a 3-Wire Flexible power Cord. The following Standards apply to Machines Driven by 120 volt and 240 volt motors: OSHA (US Occupational Safety and Health Administration 29 DFR #1910.213 (b) (3)*) NFPA (Electrical Standard for industrial Machinery, 1997 Edition, Section 8, Protection) Model No. 17023., 20" Cord on equipment switch End. 8' Cord on power End (No Plug). Wire directly into Disconnect box or instAll TwistLock Plug. Rated 120-volt, A.C., 18-amp 1 H.P. motor maximum, 50/60 cycle.
-
4.0 of 5.0 with 50 Reviews
SALE PRICE: $157.80 1% OFF
Manufacturer: Fowler
Brand: Fowler
Manufacturer: Fowler
Brand: Fowler
Includes 6" Dial Caliper 52-008-007 - .001" graduations Micrometer 52-229-201 - .0001" graduations, Range: 0-1" 6" Flexible rule with 32nds, 64ths, 10ths & 100ths graduations All contained in a fitted, shop-hardened case
-
4.0 of 5.0 with 39 Reviews
SALE PRICE: $157.80 5% OFF
Manufacturer: Fowler
Brand: Fowler
Manufacturer: Fowler
Brand: Fowler
Features 30 pointed anvil and spindle for measuring small grooves, keyways, small flutes and hard to reach dimensions Protected to IP54 specifications Large LCD Display, 8.5mm Automatic switch off Carbide measuring faces Absolute /25mm include standard
-
4.0 of 5.0 with 43 Reviews
SALE PRICE: $157.95 16% OFF
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 103-181
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 103-181
|
The Mitutoyo 103 series outside micrometer has a vernier scale in inch units for taking precise outside diameter (OD) measurements, and a ratchet-stop mechanism for uniform pressure during adjustment. The micrometer’s frame has a baked enamel finish for protection and durability. The vernier scale on the thimble and sleeve is graduated to 0.001â€, with a satin chrome rust- and glare-resistant finish. The spindle and anvil have flat measuring faces and are carbide-tipped for wear resistance. A spindle lock helps provide secure locking of the measurement position.Micrometers are precision measuring instruments that use a calibrated screw to measure small distances. These measurements are translated into large rotations of the screw that are then able to be read from a scale or a dial. Micrometers are typically used in manufacturing, machining, and mechanical engineering. There are three types of micrometer: outside, inside, and depth. Outside micrometers may also be called micrometer calipers, and are used to measure the length, width, or outside diameter of an object. Inside micrometers are typically used to measure interior diameter, as in a hole. Depth micrometers measure the height, or depth, of any shape that has a step, groove, or slot.Mitutoyo manufactures precision measuring tools, metrology equipment, and systems. The company was founded in Tokyo in 1934 and formed Mitutoyo America Corporation in 1963, which is headquartered in Aurora, IL.
-
4.0 of 5.0 with 1 Reviews
SALE PRICE: $158.04
Manufacturer: Fred V. Fowler Company, Inc.
Brand: Fowler
Model: 54-004-330-0
Manufacturer: Fred V. Fowler Company, Inc.
Brand: Fowler
Model: 54-004-330-0
|
The Fowler 54-004-330 Xtra-Value Depth Gauge and Euro-Cal IV Measuring Set includes two depth gauges: the Euro-Cal IV Electronic Caliper (54-100-330-1) and the Xtra-Value Depth Gauge (54-225-555). The Euro-Cal IV Electronic Caliper has a measurement range of 0 to 6" (0 to 150mm), and a resolution (or smallest graduation interval) of 0.0005" (0.01mm), with + or – 0.001" (or .02mm) of accuracy, and the Xtra-Value Depth Gauge has a measurement range of 0 to 6" (0 to 150mm), and a resolution of 0.0005" (0.01mm), with + or - 0.001" (0.025mm) of accuracy. The LCD screen for both gauges display in U.S./metric, and fractions (in 1/64" increments). The Euro-Cal IV Electronic Caliper is made of stainless steel and is water resistant to Ingress Protection 54 (IP54) standards. The Xtra-Value gauge includes six measuring rods and has a spring-loaded measurement button with a hold function for ease of use and accurate measurements. The gauges conform to Federal Accuracy specifications. The shipping weight of the set is 1.4 lb. and it comes with a hardened case. Depth gauges are typically used in manufacturing, machining, and mechanical engineering. Depth gauges are precision measuring instruments used to determine the depth of any shape that has a step, groove, or slot. These gauges often take the form of sliders that travel on a measuring beam or rods, are moved to position by hand, and then adjusted with a calibrated screw. The base of the gauge rests at the top of the shape whose recession is to be measured, while the beam or rods extend to the bottom of the recession to determine the measurement. Gauge position is read from a graduated scale, dial, counters, or an electronic display.The Fred V. Fowler Company manufactures inspection and measurement instruments such as electronic indicators, calipers, bore gages, and digital scales. The company, founded in 1946, is headquartered in Newton, MA.What's in the Box?Fowler 54-100-330-1 depth gaugeFowler 54-225-555 depth gauge(6) Measuring rods for 54-225-555Hardened...
-
4.0 of 5.0 with 12 Reviews
SALE PRICE: $158.69 1% OFF
Manufacturer: Starrett
Brand: Starrett
Model: 711FSBZ
Color: White
Manufacturer: Starrett
Brand: Starrett
Model: 711FSBZ
Color: White
|
The Starrett Series 711 Last Word dial test indicator has a balanced dial, a swiveling body, and inch measurements. The horizontal-face dial test indicator has a hard, chrome-plated, steel ratchet contact point for taking precise measurements in machining, layout, and inspection work. The carbide, ball-contact tip reaches into the workpiece for accurate measurements of turned, milled, and ground parts, and for tool setting gauges, fixtures, and inspections. It has a balanced dial and a white face with half-yellow shading for accurate reading when used with a mirror or in a bore jig application. The positive reversing switch changes the reading direction. The indicator has a swiveling tubular body that can be mounted from the top or the body of the indicator using a body clamp, friction holder, or shank. The indicator has a jeweled lever action for smooth operation, and a replaceable contact point. This dial test indicator meets or exceeds accuracy and performance requirements of national and international standards, and is traceable to the United States National Institutes of Standards and Technology (NIST). The indicators includes a gooseneck shank and storage box.Dial readings with three digits, such as 0-10-0, signify that the indicator has a balanced dial. Dial readings with two digits, such as 0-100, indicate that the dial has a continuous dial. Balanced dials are used to read the difference from a specific surface reference point. Continuous dials are used for direct readings and usually have a larger measurement range than balanced dials.Dial indicators are also called dial gauges, dial calipers, and probe indicators. These precision measuring tools are used to accurately measure small linear distances and object sizes. The dial magnifies the measurement so that it can more easily be read by the human eye. Frequently used in manufacturing, laboratories, and other industrial or mechanical fields, dial indicators are used anywhere a small measurement must be found and recorded or transferred, such as checkin...
-
4.0 of 5.0 with 25 Reviews
SALE PRICE: $158.69 1% OFF
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 111-115
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 111-115
|
The Mitutoyo 111 series spline micrometer has a small-diameter anvil and spindle for measuring splined shafts, slots, and keyways, and a vernier scale in metric units for taking precise outside diameter (OD) measurements. It also has a ratchet-stop mechanism for uniform pressure during adjustment. The micrometer’s frame has a baked enamel finish for protection and durability. The vernier scale on the thimble and sleeve is graduated to 0.01mm with a satin chrome rust- and glare-resistant finish. The spindle and anvil are carbide-tipped for wear resistance. A spindle lock helps provide secure locking of the measurement position. The micrometer comes with a plastic case for storage.Micrometers are precision measuring instruments that use a calibrated screw to measure small distances. These measurements are translated into large rotations of the screw that are then able to be read from a scale or a dial. Micrometers are typically used in manufacturing, machining, and mechanical engineering. There are three types of micrometer: outside, inside, and depth. Outside micrometers may also be called micrometer calipers, and are used to measure the length, width, or outside diameter of an object. Inside micrometers are typically used to measure interior diameter, as in a hole. Depth micrometers measure the height, or depth, of any shape that has a step, groove, or slot.Mitutoyo manufactures precision measuring tools, metrology equipment, and systems. The company was founded in Tokyo in 1934 and formed Mitutoyo America Corporation in 1963, which is headquartered in Aurora, IL.
-
4.0 of 5.0 with 47 Reviews
SALE PRICE: $159.00 2% OFF
Manufacturer: Fowler
Brand: Fowler
Manufacturer: Fowler
Brand: Fowler
Includes wrench and case Series No. 52-248 offers Fowler standards of fine quality and accuracy. A variety of sizes covers a range of measuring applications. Features Hammertone blue baked enamel finish Microfine graduations on satin chrome finish and carbide tipped measuring faces Ratchet stop thimble for exact and repetitive readings Spindle thread is hardened, ground and lapped Anvil & spindle hardened and precision ground with microlap finish on tips All micrometers meet or exceed U.S. Federal specifications for accuracy Includes standard
-
4.0 of 5.0 with 12 Reviews
SALE PRICE: $159.60 9% OFF
Manufacturer: Starrett
Brand: Starrett
Model: 711FSZ
Color: White
Manufacturer: Starrett
Brand: Starrett
Model: 711FSZ
Color: White
|
The Starrett Series 711 Last Word dial test indicator has a balanced dial, a swiveling body, and inch measurements. The horizontal-face dial test indicator has a hard, chrome-plated, steel ratchet contact point for taking precise measurements in machining, layout, and inspection work. The carbide, ball-contact tip reaches into the workpiece for accurate measurements of turned, milled, and ground parts, and for tool setting gauges, fixtures, and inspections. It has a balanced dial and a white face with half-yellow shading for accurate reading when used with a mirror or in a bore jig application. The positive reversing switch changes the reading direction. The indicator has a swiveling tubular body that can be mounted from the top or the body of the indicator using a body clamp, friction holder, or shank. The indicator has a jeweled lever action for smooth operation, and a replaceable contact point. This dial test indicator meets or exceeds accuracy and performance requirements of national and international standards, and is traceable to the United States National Institutes of Standards and Technology (NIST). This indicator includes a body clamp and a storage box.Dial readings with three digits, such as 0-10-0, signify that the indicator has a balanced dial. Dial readings with two digits, such as 0-100, indicate that the dial has a continuous dial. Balanced dials are used to read the difference from a specific surface reference point. Continuous dials are used for direct readings and usually have a larger measurement range than balanced dials.Dial indicators are also called dial gauges, dial calipers, and probe indicators. These precision measuring tools are used to accurately measure small linear distances and object sizes. The dial magnifies the measurement so that it can more easily be read by the human eye. Frequently used in manufacturing, laboratories, and other industrial or mechanical fields, dial indicators are used anywhere a small measurement must be found and recorded or transferred, such as checking t...
-
4.0 of 5.0 with 35 Reviews
SALE PRICE: $159.99
Manufacturer: TTC
Brand: TC1
Manufacturer: TTC
Brand: TC1
Features Accuracy: ±.0001" Flatness: ±.00003" Parallelism: ±.00005" Friction thimble for exact readings. Anvil and spindle hardened and ground. Carbide faces. Quick and easy zero adjustment. Positive locking clamp. Complete with standards. Supplied in fitted case with key.
Viewing Page 1044 of 1520
|
|