Dimensional Measurement - Page 1198

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 530-122

The Mitutoyo 530 series vernier caliper has two sets of jaws for measurement in metric units of outside dimension (OD), inside dimension (ID), step, and depth (when depth bar is included), for applications where the highest accuracy is required, especially in scientific research and in industries where parts must fit exactly. The caliper has a dual vernier scale, with both the upper and lower scales measuring in metric units. A 14-degree vernier face angle improves visibility and helps prevent parallax error in measurement reading. The caliper’s two sets of jaws provide the capability to make OD and ID measurements, as well as step measurements, where the butt end of the fixed jaw measures one end of a work piece before its upper/lower or inner/outer steps are measured. When included, a depth measuring blade with rounded edges provides the ability to make depth measurements. The scales are raised to slide easily and protect the graduation markings. A thumbwheel permits fast and easy measuring. A clamping screw on the upper scale rotates to control scale movement and locks to hold the sliding jaw’s position. The caliper is made of hardened, corrosion-resistant stainless steel with a satin chrome finish that helps reduce glare. The caliper meets Federal Accuracy Specifications GGG-C-111B. Calipers measure the distance between two opposing sides of an object. They make inside, outside, depth, or step measurements, according to their type. Calipers are commonly used in architecture, metalworking, mechanical engineering, and machining. The simplest calipers have two legs to mark the two points and require a ruler to take the measurement. More complex calipers use two sets of jaws instead of legs and have up to two graduated scales. Vernier, dial, and digital calipers give direct and accurate readings and are functionally identical, having a calibrated scale with a fixed jaw, and another jaw with a movable pointer that slides along the scale. The vernier caliper has a scale sliding parallel to the main ...

Manufacturer: Fowler Brand: Fowler Model: X-Proof

X-Proof 22 Dial Depth Gage, IP45 Fowler's 0-22 Dial Depth Gages comes with six interchangeable rods with a 0-22 capacity, carbide contact point and 2 extra points for small applications. Provides rapid measurement of hole depths. Includes: shop hardened case Rod extensions of 1 , 2 , 3 , 4 , 5 and 6 2 extra points X-Proof Special Features: Coolant, fluid and dust resistant to IP54 Specifications. Sealed bezel, top cap and dial with bellows on stem Sealed back plate Other Features: Measurements automatically registered directly on dial face in .001 graduations. The dial indicator can be easily adjusted for zero setting. Graduation: .001 0-1 travel indicator Accuracy of the dial indicator meets Federal specifications Rods can be connected together for a full 0 22 capacity. 2 extra points for small hole applications; one 0.078 dia. x 1 long and one needle point x 1 long. Base is hardened steel, ground and microlapped for accuracy Standard 4-48 thread removable carbide ball contact point Rack spindle and pinions are hardened stainless steel to ensure long wear and continuing accuracy.

Manufacturer: Merlintools Brand: Merlintools

metric M42 x 4.5mm set thread ring gage.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 2507S Color: White

The Mitutoyo dial indicator has a black or white face, a choice of flat or lug, a 0.375" stem diameter, and inch measurements. The indicator has a 0.375" diameter stem, a #4-48 UNF contact point thread mount, and is used to measure surface variations in fractional inches. The choice of black or white dial and a contrasting hand help make measurements easy to read. The dial indicator comes with a choice of flat or lug back for a variety of mounting options. Flat back dial indicators are either clamp-mounted on the stem or plate-mounted on the rear of the indicator. Lug back dial indicators have a protrusion with a hole to mount the indicator using a lug or nut and bolt. Lug back dial test indicators usually come with the lug installed horizontally. The back on most indicators can be rotated to the vertical position. It has a stem design that provides a long clamping range, no through screw-holes on the frame for dust- and water resistance, and an involute curved lifting lever that provides smooth movement of spindle and dovetail joint for a tool-less connection. This dial indicator meets ANSI standards, Japanese Industrial Standard (JIS) B7503-1997, and American Gage Design (AGD) standards for face and thread size, and bezel and stem diameter. Dial readings with three digits, such as 0-10-0, signify that the indicator has a balanced dial. Dial readings with two digits, such as 0-100, indicate that the dial has a continuous dial. Balanced dials are used to read the difference from a specific surface reference point. Continuous dials are used for direct readings and usually have a larger measurement range than balanced dials. Optional features include jeweled bearings for high sensitivity and accuracy, a revolution counter to measure overall change, waterproof, dustproof, shockproof, a white or black face, and reverse reading for depth or bore gage measurement.Dial indicators are also called dial gauges, dial calipers, and probe indicators. These precision measuring tools are used to accurately measure small linear ...

Manufacturer: INSIZE Brand: INSIZE Model: 6313-7H32

Setting ring, 7/32 dia.

Manufacturer: INSIZE Brand: INSIZE Model: 6313-5H16

Setting ring, 5/16 inch dia.

Manufacturer: INSIZE Brand: INSIZE Model: 6313-3H16

Setting ring, 3/16 inch dia.

Manufacturer: Fred V. Fowler Company, Inc. Brand: Fowler Model: 52-130-008-0

The Fowler 52-130-008 Stainless Steel Inch/Metric Dial Depth Gauge has a measurement range of 0 to 8" (0 to 200mm), and a resolution (or smallest graduation interval) of 0.001" (0.02mm), with + or – 0.001" of accuracy. The dial provides precise and easily readable measurements with inch graduations in black and metric graduations in red. The unit has a thumb roll and a positive locking screw for quick and accurate measurements. It is made of hardened steel for accurate measurements and has a raised sliding surface for the dial to prevent wear of the gauge and graduation marks. The unit has a base 4" long. The gauge conforms to Federal Accuracy specifications. The shipping weight of this gauge is 1.05 lb. and it comes with a fitted case. Depth gauges are typically used in manufacturing, machining, and mechanical engineering. Depth gauges are precision measuring instruments used to determine the depth of any shape that has a step, groove, or slot. These gauges often take the form of sliders that travel on a measuring beam or rods, are moved to position by hand, and then adjusted with a calibrated screw. The base of the gauge rests at the top of the shape whose recession is to be measured, while the beam or rods extend to the bottom of the recession to determine the measurement. Gauge position is read from a graduated scale, dial, counters, or an electronic display.The Fred V. Fowler Company manufactures inspection and measurement instruments such as electronic indicators, calipers, bore gages, and digital scales. The company, founded in 1946, is headquartered in Newton, MA.What's in the Box?Fowler 52-130-008 depth gaugeCase

Manufacturer: iGaging Brand: iGaging

iGaging ABSOLUTE Technology IndicatorThe iGaging digital electronic indicator with ABSOLUTE encoder always remembers and traces absolute origin zero or preset data. It provides unlimited measuring speed without losing its origin. This indicator will indicate absolute position when turned on. Features:SPC/USB Data PortABSOLUTE encoder technology - Unlimited measuring speed.IP54 ProtectionRead and convert Inch/mm displayOrigin setPreset valueShank diameter: 3/8"Carbide tip4-48 threaded tipFloating lug back2 Years warrantySpecifications:Range: 1"/50mmResolution: 0.00005"/0.001mmAccuracy: 0.00016"

Manufacturer: Chervon North America, Inc. Brand: Hammerhead Model: HLCL360

The HAMMERHEAD Self-Leveling 360-degree Cross Line Laser projects bright, 360-degree horizontal, vertical or cross lines onto surfaces with accuracy of ±1/8 inch at 30 feet. The continuous 360-degree horizontal laser line provides all-around leveling for a full 60 ft. diameter. The unit will self-level when positioned within 4 degrees of level; an LED indicator turns red when the unit is positioned outside of the self-leveling range. In the lock (manual) mode, the cross line laser can be positioned to project lines that are not level or plumb for projects that require them. The cross line laser may be mounted on any 5/8" threaded tripod screw. Kit includes (1) Self-Leveling 360-degree Cross Line Laser, (4) AA Batteries and (1) Soft Bag